Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM

DTC    B2325    LIN Communication Bus Malfunction

for Preparation Click here


DESCRIPTION

The main body ECU (multiplex network body ECU) monitors communication between all the ECUs connected to the door bus lines. When the main body ECU (multiplex network body ECU) detects errors in communication with all the ECUs connected to the door bus lines at 2.6-second intervals and 3 times in a row, DTC B2325 will be stored.

DTC No.
DTC Detection Condition
Trouble Area
B2325
Main body ECU (multiplex network body ECU) detects errors in communication with the ECUs connected to the door bus lines 3 times in a row.
  1. Power window regulator motor assembly (for driver side)
  2. Power window regulator motor assembly (for front passenger side)
  3. Power window regulator motor assembly (for rear RH side)
  4. Power window regulator motor assembly (for rear LH side)
  5. Multiplex network master switch assembly
  6. Sliding roof ECU (sliding roof drive gear sub-assembly)*1
  7. Double lock door control relay assembly*2
  8. Main body ECU (multiplex network body ECU)
  9. Instrument panel junction block assembly
  10. Wire harness or connector
  1. *1: w/ Moonroof with Solar Panel
  2. *2: w/ Double Locking System

WIRING DIAGRAM


B228557E03


INSPECTION PROCEDURE

NOTICE:
  1. When the sliding roof ECU (sliding roof drive gear assembly) is replaced or removed and reinstalled, it requires initialization (Click here).
  2. When a power window regulator motor assembly is replaced or removed and reinstalled, it requires initialization (Click here).
  3. When using the intelligent tester to troubleshoot with the power switch off:
    Connect the intelligent tester to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.

1.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR (DRIVER SIDE) - MASTER SWITCH)


    B201892E20
  1. Disconnect the O6*1 or N6*2 multiplex network master switch connector.

  1. Disconnect the O2*1 or N2*2 power window regulator motor (for driver side) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O6-16 (LIN2) - O2-9 (LIN)*1
    N6-16 (LIN2) - N2-9 (LIN)*2
    Always
    Below 1 Ω
    O6-16 (LIN2) - Body ground*1
    N6-16 (LIN2) - Body ground*2
    Always
    10 kΩ or higher

    1. *1: for LHD
    2. *2: for RHD
    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Multiplex Network Master Switch Assembly)
    *2
    Front view of wire harness connector
    (to Power Window Regulator Motor Assembly (for Driver Side))
    *3
    for LHD
    *4
    for RHD



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY


    B203350E04
  1. Remove the multiplex network master switch assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    16 (LIN2) - 17 (LIN1)
    Always
    Below 1 Ω
    16 (LIN2) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Component without harness connected
    (Multiplex Network Master Switch Assembly)



NG
REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (Click here)
OK


3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


  1. Remove the instrument panel junction block assembly (Click here).


    B228559E02

  1. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    This inspection is to check the LIN line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    2D-26 (LIN2) - MB-16 (LIN2)
    Always
    Below 1 Ω
    2A-27 (LIN2) - MB-16 (LIN2)
    Always
    Below 1 Ω
    2A-27 (LIN2) - Body ground
    Always
    10 kΩ or higher


    Text in Illustration 
    *1
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    *2
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    *3
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    -
    -



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (INSTRUMENT JUNCTION BLOCK - EACH ECU)

B228560E04

  1. Disconnect the N2*1, O2*2, L105*3, R23*4, P4 and Q4 connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    2D-26 (LIN2) - Q4-9 (LIN)
    Always
    Below 1 Ω
    2A-27 (LIN2) - P4-9 (LIN)
    Always
    Below 1 Ω
    2A-27 (LIN2) - O6-17 (LIN1)*1
    2A-27 (LIN2) - N6-17 (LIN1)*2
    Always
    Below 1 Ω
    2A-27 (LIN2) - N2-9 (LIN)*1
    2A-27 (LIN2) - O2-9 (LIN)*2
    Always
    Below 1 Ω
    2A-27 (LIN2) - L105-9 (MPX1)*3
    Always
    Below 1 Ω
    2A-27 (LIN2) - R23-4 (MPX1)*4
    Always
    Below 1 Ω
    2D-26 (LIN2) - Body ground
    Always
    10 kΩ or higher
    2A-27 (LIN2) - Body ground
    Always
    10 kΩ or higher

    1. *1: for LHD
    2. *2: for RHD
    3. *3: w/ Double Locking System
    4. *4: w/ Moonroof with Solar Panel

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Instrument Panel Junction Block Assembly)
    *2
    Front view of wire harness connector
    (to Instrument Panel Junction Block Assembly)
    *3
    Front view of wire harness connector
    (to Multiplex Network Master Switch Assembly)
    *4
    Front view of wire harness connector
    (to Double Lock Door Control Relay Assembly)
    *5
    Front view of wire harness connector
    (to Sliding Roof ECU (Sliding Roof Driver Gear Sub-assembly))
    *6
    Front view of wire harness connector
    (to Power Window Regulator Motor Assembly (for Front Passenger Side))
    *7
    Front view of wire harness connector
    (to Power Window Regulator Motor Assembly (for Rear RH Side))
    *8
    Front view of wire harness connector
    (to Power Window Regulator Motor Assembly (for Rear LH Side))
    *9
    for LHD
    *10
    for RHD
    *11
    w/ Double Locking System
    *12
    w/ Moonroof with Solar Panel



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK DTC OUTPUT (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for REAR LH SIDE))
  1. Reconnect the O6*1, N6*2, L105*3, 2A, 2D, R23*4, P4, O2 and N2 connectors.

    1. *1: for LHD
    2. *2: for RHD
    3. *3: w/ Double Locking System
    4. *4: w/ Moonroof with Solar Panel

  1. Clear the DTC (Click here).

  1. After 10 seconds have elapsed, check if the trouble occurs again.

  1. Check for DTCs again.

    Result:
    Result
    Proceed to
    DTC B2325 is output
    A
    DTC B2325 is not output
    B



B
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for REAR LH SIDE) (Click here)
A


6.CHECK DTC OUTPUT (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)
  1. Reconnect the Q4 connector.

  1. Disconnect the O6*1 or N6*2 connector.

    1. *1: for LHD
    2. *2: for RHD

  1. Clear the DTC (Click here).

  1. After 10 seconds have elapsed, check if the trouble occurs again.

  1. Check for DTCs again.

    Result:
    Result
    Proceed to
    DTC B2325 is output
    A
    DTC B2325 is not output
    B



B
REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (Click here)
A


7.CHECK DTC OUTPUT (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for REAR RH SIDE))
  1. Reconnect the O6*1 or N6*2 connector.

    1. *1: for LHD
    2. *2: for RHD

  1. Disconnect the P4 connector.

  1. Clear the DTC (Click here).

  1. After 10 seconds have elapsed, check if the trouble occurs again.

  1. Check for DTCs again.

    Result:
    Result
    Proceed to
    DTC B2325 is output
    A
    DTC B2325 is not output
    B



B
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for REAR RH SIDE) (Click here)
A


8.CHECK DTC OUTPUT (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for DRIVER SIDE))
  1. Reconnect the P4 connector.

  1. Disconnect the O2*1 or N2*2 connector.

    1. *1: for LHD
    2. *2: for RHD

  1. Clear the DTC (Click here).

  1. After 10 seconds have elapsed, check if the trouble occurs again.

  1. Check for DTCs again.

    Result:
    Result
    Proceed to
    DTC B2325 is output
    A
    DTC B2325 is not output
    B



B
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for DRIVER SIDE) (Click here)
A


9.CHECK DTC OUTPUT (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for FRONT PASSENGER SIDE))
  1. Reconnect the O2*1 or N2*2 connector.

  1. Disconnect the N2*1 or O2*2 connector.

    1. *1: for LHD
    2. *2: for RHD

  1. Clear the DTC (Click here).

  1. After 10 seconds have elapsed, check if the trouble occurs again.

  1. Check for DTCs again.

    Result:
    Result
    Proceed to
    DTC B2325 is output (w/ Moonroof with Solar Panel)
    A
    DTC B2325 is output (w/ Double Locking System and w/o Moonroof with Solar Panel)
    B
    DTC B2325 is output (w/o Double Locking System and w/o Moonroof with Solar Panel)
    C
    DTC B2325 is not output
    D



B
Go to step 11

C
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)

D
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for FRONT PASSENGER SIDE) (Click here)
A


10.CHECK DTC OUTPUT (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY))
  1. Reconnect the N2*1 or O2*2 connector.

    1. *1: for LHD
    2. *2: for RHD

  1. Disconnect the R23 connector.

  1. Clear the DTC (Click here).

  1. After 10 seconds have elapsed, check if the trouble occurs again.

  1. Check for DTCs again.

    Result:
    Result
    Proceed to
    DTC B2325 is output (w/ Double Locking System)
    A
    DTC B2325 is output (w/o Double Locking System)
    B
    DTC B2325 is not output
    C



B
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)

C
REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) (Click here)
A


11.CHECK DTC OUTPUT (DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY)
  1. Reconnect the R23*1 connector.

    1. *1: w/ Moonroof with Solar Panel

  1. Disconnect the L105 connector.

  1. Clear the DTC (Click here).

  1. After 10 seconds have elapsed, check if the trouble occurs again.

  1. Check for DTCs again.

    Result:
    Result
    Proceed to
    DTC B2325 is output
    A
    DTC B2325 is not output
    B



B
REPLACE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY (Click here)
A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)