Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › INTELLIGENT PARKING ASSIST SYSTEM

DTC    C1621    Back Camera Power Supply Failure

DTC    C1622    Open or Short Circuit in Back Camera Signal

for Preparation Click here


DESCRIPTION

These DTCs are stored if the parking assist ECU judges as a result of its self check that the signals or signal lines between the parking assist ECU and rear television camera assembly are not normal.

DTC No.
DTC Detection Condition
Trouble Area
C1621
Rear television camera power supply failure
  1. Harness or connector
  2. Rear television camera assembly
  3. Parking assist ECU
C1622
An open or short in the rear television camera signal circuit
  1. Harness or connector
  2. Rear television camera assembly
  3. Parking assist ECU

WIRING DIAGRAM


E226210E05


INSPECTION PROCEDURE

NOTICE:
  1. When the "System initializing" message is displayed on the navigation ECU sub-assembly after the auxiliary battery cable has been disconnected, correct the steering angle neutral point (Click here).
  2. Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the intelligent parking assist system may be needed (Click here).

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - REAR TELEVISION CAMERA ASSEMBLY)
  1. Disconnect the L151 connector from the parking assist ECU.

  1. Disconnect the V6 connector from the rear television camera assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L151-14 (CB+) - V6-4 (CB+)
    Always
    Below 1 Ω
    L151-15 (CV+) - V6-2 (CV+)
    Always
    Below 1 Ω
    L151-37 (CGND) - V6-3 (CGND)
    Always
    Below 1 Ω
    L151-38 (CV-) - V6-1 (CV-)
    Always
    Below 1 Ω
    L151-14 (CB+) - Body ground
    Always
    10 kΩ or higher
    L151-15 (CV+) - Body ground
    Always
    10 kΩ or higher
    L151-37 (CGND) - Body ground
    Always
    10 kΩ or higher
    L151-38 (CV-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK PARKING ASSIST ECU (CV-, CGND)


    E224375E02
  1. Reconnect the L151 connector to the parking assist ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L151-37 (CGND) - Body ground
    Always
    Below 1 Ω
    L151-38 (CV-) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component with harness connected
    (Parking Assist ECU)



NG
REPLACE PARKING ASSIST ECU (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY - POWER SOURCE)
  1. Disconnect the V6 connector from the rear television camera assembly.



    E228124E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    V6-3 (CGND) - V6-4 (CB+)
    Power switch on (READY)
    Reverse (R) selected
    5.8 to 7.0 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Rear Television Camera Assembly)



NG
REPLACE PARKING ASSIST ECU (Click here)
OK


4.CHECK PARKING ASSIST ECU (CV+, GND1)
  1. Reconnect the V6 connector to the rear television camera assembly.



    E226205E02
  1. Reconnect the L151 connectors to the parking assist ECU.

  1. Check the waveform of the rear television camera assembly using an oscilloscope.

    HINT:
    A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.

    OK:
    Waveform is as shown in the illustration.

    Item
    Content
    Terminal No. (Symbol)
    L151-15 (CV+) - L152-4 (GND1)
    Tool Setting
    200 mV/DIV., 50 μsec./DIV.
    Condition
    Power switch on (READY), reverse (R) selected

    HINT:
    The video waveform changes according to the image sent by the rear television camera assembly.

    Text in Illustration 
    *a
    Component with harness connected
    (Parking Assist ECU)
    *b
    Waveform 1 (camera lens not covered, displaying an image)
    *c
    Waveform 2 (camera lens covered, blacking out the screen)
    *d
    Synchronization Signal
    *e
    Video Waveform



NG
REPLACE REAR TELEVISION CAMERA ASSEMBLY (Click here)
OK

REPLACE PARKING ASSIST ECU (Click here)