NAVIGATION SYSTEM (for HDD) > OPERATION CHECK |
| CHECK SYSTEM NORMAL CONDITION |
If the symptom is applicable to any of the following, it is intended behavior, and not a malfunction.
| Symptom | Answer |
| A longer route than expected is chosen. | Depending on the road conditions, the navigation receiver assembly may determine that a longer route is quicker. |
| Even when distance priority is high, the shortest route is not shown. | Some routes may not be advised due to safety concerns. |
| When the vehicle is put into motion immediately after the hybrid system starts, the navigation system deviates from the current position. | If the vehicle starts before the navigation system activates, the system may not react. |
| When running on certain types of roads, especially new roads, the vehicle position deviates from the current position. | When the vehicle is driving on new roads not available on the hard disk drive, the system attempts to match it to another nearby road, causing the position mark to deviate. |
![]() |
The following symptoms are not malfunctions, but are caused by errors inherent in the GPS, gyro sensor, speed sensor or navigation receiver assembly.
The current position mark may be displayed on a nearby parallel road.
![]() |
Immediately after a fork in the road, the current vehicle position mark may be displayed on the wrong road.
![]() |
When the vehicle turns right or left at an intersection, the current vehicle position mark may be displayed on a nearby parallel road.
![]() |
When the vehicle is carried, such as on a ferry, and the vehicle itself is not running, the current vehicle position mark may be displayed in the position where the vehicle was until a measurement can be performed by GPS.
![]() |
When the vehicle travels on a steep hill, the current vehicle position mark may deviate from the correct position.
![]() |
When the vehicle makes a continuous turn (e.g. 360, 720, 1080 degrees), the current vehicle position mark may deviate from the correct position.
![]() |
When the vehicle moves erratically, such as constant lane changes, the current vehicle position mark may deviate from the correct position.
![]() |
When the power switch is turned on (ACC or IG) on a turntable before parking, the current vehicle position mark may not indicate the correct direction. The same will occur when the vehicle comes out of the parking garage.
![]() |
When the vehicle travels on a snowy road or a mountain path with the chains installed or using a spare tire, the current vehicle position mark may deviate from the correct position.
![]() |
When the tires are changed, the current vehicle position mark may deviate from the correct position.
| CHECK HARD DISK DRIVE |
Enter diagnostic mode (Click here).
![]() |
Select "Failure Diagnosis" from the "Service Menu" screen.
![]() |
Hard disk drive check
Select "HDD Check" to start the HDD check.
Check that the result is displayed when the HDD check is completed.
| Result | Description |
| Checking | While the check is in progress |
| OK | Hard disk drive is normal |
| NG | Hard disk drive is malfunctioning |
| CHECK PANEL & STEERING SWITCH |
Enter diagnostic mode (Click here).
![]() |
Select "Function Check/Setting" from the "Service Menu" screen.
![]() |
Select "Panel & Steering Switch" from the "Function Check/Setting" screen.
Panel & Steering Switch Check Mode
![]() |
Operate each switch and check that the switch names and condition are correctly displayed.
| Display | Content |
| *1: Push switch name |
|
| *2: Rotary switch name | Name of the rotary switch is displayed. |
| *3: Rotary switch direction | Direction of the rotary switch is displayed. |
| CHECK TOUCH SWITCH |
Enter diagnostic mode (Click here).
![]() |
Select "Function Check/Setting" from the "Service Menu" screen.
![]() |
Select "Touch Switch" from the "Function Check/Setting" screen.
Touch Switch Check
![]() |
Touch the display anywhere in the open area to perform the check when the "Touch Switch Check" screen is displayed.
| CHECK MIC & VOICE RECOGNITION |
Enter diagnostic mode (Click here).
![]() |
Select "Function Check/Setting" from the "Service Menu" screen.
![]() |
Select "Mic & Voice Recognition" from the "Function Check/Setting" screen.
Microphone & Voice Recognition Check
![]() |
When speaking into the microphone, check that the microphone input level meter changes according to the input level.
Push the recording switch and perform voice recording.
Check that the recording indicator remains on while recording and that the recording can be played normally.
| CHECK COLOR BAR |
Enter diagnostic mode (Click here).
![]() |
Select "Function Check/Setting" from the "Service Menu" screen.
![]() |
Select "Color Bar" from the "Function Check/Setting" screen.
Color Bar Check Mode
![]() |
Select a color bar from the "Color Bar Check Mode" screen.
Check the display color.
| CHECK GPS & VEHICLE SENSORS |
Enter diagnostic mode (Click here).
![]() |
Select "Function Check/Setting" from the "Service Menu" screen.
![]() |
Select "GPS & Vehicle Sensors" from the "Function Check/Setting" screen.
GPS information
![]() |
When the "GPS Information" screen is displayed, check the GPS conditions.
Select "Sensors Check" from the "GPS information" screen.
Vehicle Sensors
![]() |
Check all the signals and sensors when vehicle signal information is displayed.
| CHECK VEHICLE SIGNAL |
Enter diagnostic mode (Click here).
![]() |
Select "Function Check/Setting" from the "Service Menu" screen.
![]() |
Select "Vehicle Signal" from the "Function Check/Setting" screen.
Vehicle Signal Check Mode
![]() |
When the "Vehicle Signal Check Mode" screen is displayed, check all the vehicle signal conditions.
| CHECK SOUND LIBRARY SETTING |
Enter diagnostic mode (Click here).
![]() |
Select "Function Check/Setting" from the "Service Menu" screen.
![]() |
Select "Sound Library Setting" from the "Function Check/Setting" screen.
![]() |
Sound Library Information
| CHECK HANDS-FREE VOLUME SETTING |
Enter diagnostic mode (Click here).
![]() |
Select "Function Check/Setting" from the "Service Menu" screen.
![]() |
Select "Hands-free Volume Setting" from the "Function Check/Setting" screen.
Hands-free Volume Setting
![]() |
Check the hands-free volume level.
| Display | Content |
| *1: Receive voice level adjustment | Setting possible for the voice level received from "Bluetooth" compatible phones. |
| CHECK CAMERA SETTING |
Enter diagnostic mode (Click here).
![]() |
Select "Function Check/Setting" from the "Service Menu" screen.
![]() |
Select "Camera Setting" from the "Function Check/Setting" screen.
![]() |
MODE SETTING