Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM

DTC    C1A4B    Stop Light Relay Circuit

for Preparation Click here


DESCRIPTION

The brake booster with master cylinder (skid control ECU) sends a stop light operation signal to the stop light control relay. When the brake booster with master cylinder (skid control ECU) detects a malfunction in the stop light circuit, the driving support ECU stores DTC C1A4B.

DTC No.
DTC Detection Condition
Trouble Area
C1A4B
Either of the following conditions is met:
  1. When the power switch is on (IG), the IG1 terminal voltage is between 11 and 14 V and the stop light illumination output signal (STPO) is output, the signal is not received at terminal STP2 for 0.3 seconds or more.
  2. When the power switch is on (IG), the IG1 terminal voltage is between 11 and 14 V and the stop light illumination output signal (STPO) is not output, the signals received at terminals STP and STP2 are different for 0.3 seconds or more.
  1. Lighting system
  2. Electronically controlled brake system
  3. Harness or connector
  4. Stop light control relay
  5. Driving support ECU

WIRING DIAGRAM


A318941E01


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. When this DTC is output, malfunction in the lighting system is suspected. Check if the lighting system is functioning normally (Click here).

1.CHECK STOP LIGHT OPERATION
  1. Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

    OK:

    Condition
    Illumination Condition
    Brake pedal depressed
    On
    Brake pedal released
    Off



NG
GO TO LIGHTING SYSTEM (Click here)
OK


2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT CONTROL RELAY)
  1. Turn the power switch off.

  1. Disconnect the A28 stop light control relay connector.



    A318942E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A28-6 (+B) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Stop Light Control Relay)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL RELAY - BODY GROUND)
  1. Turn the power switch off.

  1. Disconnect the A28 stop light control relay connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    A28-8 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK TERMINAL VOLTAGE (STP TERMINAL)
  1. Turn the power switch off.

  1. Disconnect the A58 brake booster with master cylinder (skid control ECU) connector.



    A318943E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A58-33 (STP) - Body ground
    Brake pedal depressed
    11 to 14 V
    A58-33 (STP) - Body ground
    Brake pedal released
    Below 1.5 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Brake Booster with Master Cylinder (Skid Control ECU))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK TERMINAL VOLTAGE (STP TERMINAL)
  1. Turn the power switch off.

  1. Disconnect the A28 stop light control relay connector.



    A318942E02
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A28-5 (STP) - Body ground
    Brake pedal depressed
    11 to 14 V
    A28-5 (STP) - Body ground
    Brake pedal released
    Below 1.5 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Stop Light Control Relay)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (STOP LIGHT RELAY)
  1. Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

  1. Perform "Active Test" according to the display on intelligent tester.

    Tester Display
    Measurement Item
    Control Range
    Diagnostic Note
    Stop Light Relay
    Stop light control relay (STOP LP)
    ON or OFF
    Stop lights come on

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light Relay Output
    Stop light control relay (STOP LP) output/
    ON or OFF
    ON: Relay output on (Stop light on)
    OFF: Relay output off (Stop light off)
    -

    Result:

    Result
    Result
    Data List item changes between ON and OFF, but stop lights do not turn on
    A
    Data List item changes between ON and OFF and stop lights turn on and off
    B



B
Go to step 8
A


7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - STOP LIGHT CONTROL RELAY)
  1. Turn the power switch off.

  1. Disconnect the A58 brake booster with master cylinder (skid control ECU) connector.

  1. Disconnect the A28 stop light control relay connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    A58-3 (STPO) - A28-9 (ACC)
    Always
    Below 1 Ω
    A58-3 (STPO) - A28-9 (ACC)
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - STOP LIGHT CONTROL RELAY)
  1. Turn the power switch off.

  1. Disconnect the A58 brake booster with master cylinder (skid control ECU) connector.

  1. Disconnect the A28 stop light control relay connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    A58-6 (STP2) - A28-1 (OUT)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.CHECK TERMINAL VOLTAGE (STP2 TERMINAL)
  1. Turn the power switch off.

  1. Disconnect the A58 brake booster with master cylinder (skid control ECU) connector.



    A318943E02
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A58-6 (STP2) - Body ground
    Brake pedal depressed
    11 to 14 V
    A58-6 (STP2) - Body ground
    Brake pedal released
    Below 1.5 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Brake Booster with Master Cylinder (Skid Control ECU))



NG
REPLACE STOP LIGHT CONTROL RELAY (Click here)
OK


10.CHECK FOR DTCs (PRE-CRASH 2)
  1. Turn the power switch off and wait for at least 2 minutes.

  1. Clear the DTCs (Click here).

  1. Make sure that the DTC detection conditions are met.

    HINT:
    If the detection conditions are not met, the system cannot detect the malfunction.
    1. Using the intelligent tester, perform the Active Test "Stop Light Relay" with the power switch on (IG).

  1. Check for DTCs (Click here).

    Result:

    Result
    Result
    DTC C1A4B is not output
    A
    DTC C1A4B is output
    B

    NOTICE:
    When replacing the driving support ECU, always replace it with a new one. If a driving support ECU which was installed to another vehicle is used, the information stored in the driving support ECU will not match the information from the vehicle. As a result, a DTC may be stored.



B
REPLACE DRIVING SUPPORT ECU (Click here)
A

END