Home › Engine / Hybrid System › 2ZR-FXE EMISSION CONTROL › EGR VALVE

EGR VALVE > INSTALLATION

for Preparation Click here



1. INSTALL WIRE HARNESS CLAMP BRACKET


    A212670
  1. Install the wiring harness clamp bracket with the bolt.



2. INSTALL EGR VALVE ASSEMBLY


    A218077E01
  1. Temporarily install the EGR valve assembly with the 2 nuts (A and B).
    Text in Illustration 
    *1
    Bolt
    *2
    Stud Bolt and Nut

  1. Set a new gasket and EGR valve with cooler assembly.

  1. Using an E8 "TORX" wrench, install the 4 stud bolts.

    Torque:
    9.5 N*m{ 97 kgf*cm , 84 in.*lbf }

  1. Temporarily install the 2 nuts (C) and bolt.

  1. Tighten the nut (A).

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Tighten the 3 nuts (B and C) and bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    NOTICE:
    Make sure that all installation surfaces of the EGR valve with cooler assembly are in even contact when tightening the bolts and nuts.



    A212666
  1. Connect the connector, wire harness clamp and 4 water hoses.



3. INSTALL EGR PIPE ASSEMBLY


    A212665
  1. Install 2 new gaskets and EGR pipe assembly with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    Make sure to tighten the 4 bolts evenly until the flanges of the EGR pipe assembly contact with the installation surfaces.



    A212664
  1. Install the wire harness support with the bolt.



    A212663
  1. Connect the 2 wire harness clamps.



4. INSTALL AIR CLEANER CASE


    A212314
  1. Install the air cleaner case with the 3 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Install the hose to the 3 hose clamps.

  1. Install the air cleaner filter element.



5. INSTALL INLET AIR CLEANER ASSEMBLY


    A212313
  1. Install the inlet air cleaner assembly with the 3 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the wire harness clamp to the inlet air cleaner assembly.

  1. Install the hose to the hose clamp.



6. INSTALL AIR CLEANER CAP SUB-ASSEMBLY


    A212312E01
  1. Install the air cleaner cap sub-assembly with the 2 clamps.

  1. Tighten the hose clamp.



    A212311
  1. Connect the mass air flow meter connector.



7. INSTALL NO. 2 CYLINDER HEAD COVER


    A213020
  1. Engage the 3 clips to install the cover.

    NOTICE:
    1. Be sure to engage the clips securely.
    2. Do not apply excessive force or hit the cover to engage the clips. This may cause the cover to break.



8. ADD COOLANT (for Engine)
  1. Tighten the radiator drain cock plug.

  1. Tighten the cylinder block drain cock plug.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Remove the reservoir tank cap.

  1. Connect the hose to the air release valve.

  1. Loosen the air release valve.

  1. Add TOYOTA Super Long Life Coolant (SLLC) to the reservoir tank filler opening until coolant overflows from the air release valve. Then tighten the air release valve.

    Standard Capacity:
    Item
    Capacity
    Engine coolant
    w/ Exhaust Heat Recirculation System:
    7.2 liters (7.6 US qts, 6.3 lmp. qts)
    w/o Exhaust Heat Recirculation System:
    6.5 liters (6.8 US qts, 5.7 lmp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).
    2. Contact your TOYOTA dealer for further details.

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Disconnect the hose from the air release valve.



    A213418E01
  1. Add coolant to B line of the reservoir tank.
    Text in Illustration 
    *1
    B Line

  1. Squeeze the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level is low, add coolant.

  1. Put the engine in inspection mode (Click here).

  1. Install the reservoir tank cap and air release valve, and warm up the engine sufficiently.

  1. Bleed air from the cooling system.

    NOTICE:
    1. Before starting the engine, turn the A/C switch off.
    2. Adjust the heater control to the maximum hot setting.
    3. Adjust the blower speed to low setting.


    1. Warm up the engine until the thermostat opens. While the thermostat is open, allow the coolant to circulate for several minutes.

      HINT:
      The thermostat opening timing can be confirmed by squeezing the inlet radiator hose by hand, and sensing vibrations when the engine coolant starts to flow inside the hose.

      CAUTION:
      When squeezing the radiator hose:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the radiator fan.

    2. Squeeze the inlet and outlet radiator hoses several times by hand to bleed air from the system.

      CAUTION:
      When squeezing the radiator hose:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the radiator fan.



    A213418E02
  1. After the engine has cooled down, check that the coolant level is between full and low.
    Text in Illustration 
    *1
    Full Line
    *2
    Low Line
    If the coolant level is low, add coolant to the full line on the reservoir tank.



9. INSPECT FOR COOLANT LEAK (for Engine)

CAUTION:
Do not remove the reservoir tank cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

NOTICE:
Before performing each inspection, turn the A/C switch off.

  1. Remove the reservoir tank cap.



    A213419
  1. Fill the radiator and reservoir with coolant, and then attach a radiator cap tester.

  1. Put the engine in inspection mode (Click here).

  1. Warm up the engine.

  1. Using the reservoir cap tester, increase the pressure inside the radiator to 108 kPa (1.1 kgf/cm2, 16 psi), and check that the pressure does not drop. If the pressure drops, check the hoses, radiator, front exhaust pipe assembly and the heater hose around and engine water pump assembly for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.

  1. Remove the radiator cap tester.

  1. Install the reservoir tank cap.



10. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)


    C209144
  1. Install the outer cowl top panel sub-assembly with the 9 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



    C209145
  1. Bend the water guard plate RH and engage the claw.



    C209147
  1. Bend the No. 1 heater air duct splash shield seal and engage the claw.



    C205696
  1. Engage the clamp to install the wire harness.



11. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)


    C205557
  1. Install the outer cowl top panel with the 9 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



    C205561
  1. Bend the water guard plate RH and engage the claw.



    C205559
  1. Bend the No. 1 heater air duct splash shield seal and engage the claw.



    C205555E01
  1. Engage the clamp*2 of the wire harness.

  1. Engage the clamp*1 and connect the connector (w/ Windshield Deicer).



    C205556
  1. Engage the clamp of the wire harness.



12. INSTALL COWL BODY MOUNTING REINFORCEMENT LH (for LHD)


    C209143
  1. Install the cowl body mounting reinforcement LH with the 3 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



13. INSTALL COWL BODY MOUNTING REINFORCEMENT LH (for RHD)


    C205554
  1. Install the cowl body mounting reinforcement LH with the 3 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



14. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
  1. Install the windshield wiper motor and link assembly (Click here).