DTC P261B Engine Coolant Pump "B" Control Malfunction |
DTC P261C Engine Coolant Pump "B" Control Circuit Low |
DTC P261D Engine Coolant Pump "B" Control Circuit High |
| DTC No. | DTC Detection Condition | Trouble Area |
| P261B | Engine water pump assembly speed is less than 900 rpm while the engine water pump assembly is operating (1 trip detection logic) |
|
| P261C | Engine water pump assembly output voltage is less than specified value while the engine water pump assembly is operating (1 trip detection logic) |
|
| P261D | Engine water pump assembly output voltage is higher than specified value while the engine water pump assembly is operating (1 trip detection logic) |
|

| 1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE ELECTRIC WATER PUMP) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the Electric Water Pump.
Touch the engine water pump assembly and check that the pump is operating (vibrating).
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (ENGINE WATER PUMP ASSEMBLY - ECM) |
Disconnect the engine water pump assembly connector.

Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D13-2 (NWP) - A57-11 (WPI) | Always | Below 1 Ω |
| D13-4 (SWP) - A57-10 (WPO) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| D13-2 (NWP) or A57-11 (WPI) - Body ground | Always | 10 kΩ or higher |
| D13-4 (SWP) or A57-10 (WPO) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Engine Water Pump Assembly) | *2 | Front view of wire harness connector (to ECM) |
Reconnect the engine water pump assembly connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 3.CHECK ECM (WPI VOLTAGE) |
![]() |
Disconnect the engine water pump assembly connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D13-2 (NWP) - Body ground | Power switch on (IG) | 11 to 14 V |
| *1 | Front view of wire harness connector (to Engine Water Pump Assembly) |
Reconnect the engine water pump assembly connector.
|
| ||||
| OK | ||
| ||
| 4.CHECK ENGINE WATER PUMP ASSEMBLY (POWER SOURCE) |
![]() |
Disconnect the engine water pump assembly connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D13-1 (+B) - Body ground | Power switch on (IG) | 11 to 14 V |
| *1 | Front view of wire harness connector (to Engine Water Pump Assembly) |
Reconnect the engine water pump assembly connector.
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (ENGINE WATER PUMP ASSEMBLY - BODY GROUND) |
![]() |
Disconnect the engine water pump assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D13-5 (PGND) - Body ground | Always | Below 1 Ω |
| *1 | Front view of wire harness connector (to Engine Water Pump Assembly) |
Reconnect the engine water pump assembly connector.
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (ENGINE WATER PUMP ASSEMBLY - ECM) |
Disconnect the engine water pump assembly connector.

Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D13-2 (NWP) - A57-11 (WPI) | Always | Below 1 Ω |
| D13-4 (SWP) - A57-10 (WPO) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| D13-2 (NWP) or A57-11 (WPI) - Body ground | Always | 10 kΩ or higher |
| D13-4 (SWP) or A57-10 (WPO) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Engine Water Pump Assembly) | *2 | Front view of wire harness connector (to ECM) |
Reconnect the engine water pump assembly connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 7.REPLACE ENGINE WATER PUMP ASSEMBLY |
Replace the engine water pump assembly (Click here).
| NEXT | |
| 8.CHECK WHETHER DTC OUTPUT RECURS (DTC P261B, P261C OR P261D) |
Connect the intelligent tester to the DLC3.
Turn the power switch on.
Turn the tester on.
Put the engine in inspection mode (Click here).
Start the engine and warm it up (until the engine coolant temperature is 75°C (167°F) or higher).
Idle the engine for 20 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P261B, P261C or P261D is output | A |
| DTC is not output | B |
|
| ||||
| A | ||
| ||
| 9.INSPECT RELAY (ENG W/P RELAY) |
![]() |
Remove the ENG W/P relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 - 5 | No battery voltage applied between terminals 1 and 2 | 10 kΩ or higher |
| 3 - 5 | Battery voltage applied between terminals 1 and 2 | Below 1 Ω |
Reinstall the ENG W/P relay to the engine room relay block.
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (ENG W/P RELAY - ENGINE WATER PUMP ASSEMBLY) |
Remove the ENG W/P relay from the engine room relay block.

Disconnect the engine water pump assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| ENG W/P relay terminal 5 - D13-1 (+B) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| ENG W/P relay terminal 5 or D13-1 (+B) - Body ground | Always | 10 kΩ or higher |
| *1 | Engine Room Relay Block | *2 | Front view of wire harness connector (to Engine Water Pump Assembly) |
Reinstall the ENG W/P relay to the engine room relay block.
Reconnect the engine water pump assembly connector.
|
| ||||
| OK | |
| 11.CHECK RELAY (ENG W/P RELAY POWER SOURCE) |
![]() |
Remove the ENG W/P relay from the engine room relay block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| ENG W/P relay terminal 3 - Body ground | Always | 11 to 14 V |
| *1 | Engine Room Relay Block |
Reinstall the ENG W/P relay to the engine room relay block.
|
| ||||
| OK | |
| 12.CHECK HARNESS AND CONNECTOR (ENG W/P RELAY - BODY GROUND) |
![]() |
Remove the ENG W/P relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| ENG W/P relay terminal 1 - Body ground | Always | Below 1 Ω |
| *1 | Engine Room Relay Block |
Reinstall the ENG W/P relay to the engine room relay block.
|
| ||||
| OK | ||
| ||