Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › BLOCKING SYSTEM

DTC    B1587    Lost Communication for Immobiliser Communication Circuit

for Preparation Click here


DESCRIPTION

When one of the following occurs: 1) the telephone transceiver assembly detects errors in its own communications with the ID code box (immobiliser code ECU); 2) the telephone transceiver assembly detects errors in the communication lines; 3) the ECU communication ID between the ID code box (immobiliser code ECU) and telephone transceiver assembly is different and an engine start is attempt, the telephone transceiver assembly stores DTC B1587.

DTC Code
DTC Detection Condition
Trouble Area
B1587
Either condition is met:
  1. Error in communication between telephone transceiver assembly and ID code box (immobiliser code ECU)
  2. Error in communication lines
  3. Communication ID is different during communication with ID code box (immobiliser code ECU)
  1. Telephone transceiver assembly
  2. ID code box (immobiliser code ECU)
  3. Wire harness or connector

WIRING DIAGRAM


B278907E10


INSPECTION PROCEDURE

NOTICE:
  1. Before troubleshooting for these DTCs, make sure no engine immobiliser system DTCs are present. If present, troubleshoot the engine immobiliser system DTCs first.
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  3. When replacing the telephone transceiver assembly or ID code box (immobiliser code ECU), refer to the Service Bulletin.
  4. When the telephone transceiver assembly is replaced, it is necessary to set the contract mode.

1.CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Turn the power switch off.

  1. Start the hybrid system.

  1. Check for DTCs.

    OK:
    DTC B1587 is not output.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.REREGISTER ECU COMMUNICATION ID
  1. Reregister the ECU communication ID.

    HINT:
    Refer to the Service Bulletin.


NEXT


3.CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Turn the power switch off.

  1. Start the hybrid system.

  1. Check for DTCs.

    OK:
    DTC B1587 is not output.



NG
Go to step 4
OK

USE SIMULATION METHOD TO CHECK 

4.CHECK CONNECTION OF CONNECTOR
  1. Turn the power switch off.

  1. Check that the connectors are properly connected to the telephone transceiver assembly and ID code box (immobiliser code ECU).

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTOR CORRECTLY
OK


5.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - ID CODE BOX (IMMOBILISER CODE ECU))
  1. Disconnect the L10 ID code box (immobiliser code ECU) connector.

  1. Disconnect the L156 telephone transceiver assembly connector.

  1. Measure the resistance and voltage according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L156-1 (BLK1) - L10-5 (EFII)
    Always
    Below 1 Ω
    L156-1 (BLK1) - Body ground
    Always
    10 kΩ or higher
    L10-5 (EFII) - Body ground
    Always
    10 kΩ or higher
    L156-2 (BLK4) - L10-6 (EFIO)
    Always
    Below 1 Ω
    L156-2 (BLK4) - Body ground
    Always
    10 kΩ or higher
    L10-6 (EFIO) - Body ground
    Always
    10 kΩ or higher

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L156-1 (BLK1) - Body ground
    Always
    Below 1 V
    L156-2 (BLK4) - Body ground
    Always
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
  1. Temporarily replace the ID code box (immobiliser code ECU) with a new one.

    HINT:
    Refer to the Service Bulletin.


NEXT


7.REGISTER ECU COMMUNICATION ID
  1. Register the ECU communication ID.

    HINT:
    Refer to the Service Bulletin.


NEXT


8.CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Turn the power switch off.

  1. Start the hybrid system.

  1. Check for DTCs.

    OK:
    DTC B1587 is not output.



NG
REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
OK

END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE)