Home › Suspension › FRONT SUSPENSION › FRONT SHOCK ABSORBER

FRONT SHOCK ABSORBER > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for the LH side and RH side.
  2. The procedure listed below is for the LH side.



1. SECURE FRONT SHOCK ABSORBER ASSEMBLY


    C205592E01
  1. Install a bolt and nut to the front shock absorber as shown in the illustration and secure the front shock absorber in a vise.

    Standard length A:
    40 mm (1.575 in.)



2. INSTALL FRONT COIL SPRING LOWER INSULATOR


    C188480E02
  1. Install the front coil spring lower insulator to the front shock absorber assembly.
    Text in Illustration 
    *1
    Positioning Pin
    *2
    Depression

    NOTICE:
    When installing the insulator, fit the insulator to the depression of the spring seat and align the positioning pin into the hole.



3. INSTALL FRONT SPRING BUMPER


    C232826
  1. Install the front spring bumper to the front shock absorber assembly.

    NOTICE:
    Face the smaller diameter end of the front spring bumper downward.



4. INSTALL FRONT COIL SPRING


    C153584E01
  1. Using SST, compress the front coil spring.

    SST
    09727-30021   (09727-00010, 09727-00021, 09727-00031)

    NOTICE:
    Do not use an impact wrench. It will damage the SST.

    HINT:
    If the front coil spring is compressed at an angle, using 2 SST will make the work easier.



    C159194E04
  1. Install the front coil spring.
    Text in Illustration 
    *1
    Paint Mark

    NOTICE:
    1. Make sure that the end of the front coil spring is positioned in the depression of the lower spring seat.
    2. Make sure to install the coil spring with the paint mark facing downward.



5. INSTALL FRONT COIL SPRING UPPER INSULATOR


6. INSTALL FRONT COIL SPRING UPPER SEAT


7. INSTALL STRUT MOUNTING BEARING


    C207004E01
  1. Install the strut mounting bearing.
    Text in Illustration 
    *1
    Upper Side
    *2
    Lower Side

    NOTICE:
    Do not install the bearing upside down.



8. INSTALL FRONT SUSPENSION SUPPORT SUB-ASSEMBLY
  1. Install the front suspension support sub-assembly to the front shock absorber assembly.

    NOTICE:
    When installing, align the cutout on the front suspension support sub-assembly and the shock absorber piston rod end.



9. TEMPORARILY TIGHTEN FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT


    C188975E05
  1. Install the collar to the front shock absorber assembly.



    C188476
  1. Temporarily tighten a new front support to front shock absorber nut.

  1. Remove SST from the front coil spring.

    NOTICE:
    Do not use an impact wrench. It will damage SST.



10. INSTALL FRONT SHOCK ABSORBER WITH COIL SPRING


    C205591
  1. Install the front shock absorber with coil spring (upper side) with the 3 nuts.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



    C205584
  1. Install the front shock absorber with coil spring (lower side) to the steering knuckle with the 2 bolts and 2 nuts.

    Torque:
    240 N*m{ 2447 kgf*cm , 177 ft.*lbf }

    NOTICE:
    While keeping the bolts from rotating, tighten the nuts.



11. FULLY TIGHTEN FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT


    C205589
  1. Fully tighten the front support to front shock absorber nut.

    Torque:
    47 N*m{ 479 kgf*cm , 35 ft.*lbf }



12. INSTALL FRONT SUSPENSION SUPPORT DUST COVER


    C208846
  1. Install the front suspension support dust cover.



13. INSTALL FRONT SPEED SENSOR


    C208843
  1. Install the front speed sensor and front flexible hose to the front shock absorber with the bolt and clamp.

    Torque:
    19 N*m{ 192 kgf*cm , 14 ft.*lbf }

    NOTICE:
    Do not twist the front speed sensor when installing it.

    HINT:
    Install the front flexible hose first and then the speed sensor harness bracket.



14. INSTALL FRONT STABILIZER LINK ASSEMBLY


    C205585
  1. Install the front stabilizer link assembly to the front shock absorber with coil spring with the nut.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud bolt.



15. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY


    C205669
  1. Install the outer cowl top panel sub-assembly with the 9 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



    C205673
  1. Bend the water guard plate RH and engage the claw.



    C205671
  1. Bend the No. 1 heater air duct splash shield seal and engage the claw.



    C205668E01
  1. Engage the 2 clamps and guide to install the wire harness.
    Text in Illustration 
    *1
    Clamp
    *2
    Guide



16. INSTALL COWL BODY MOUNTING REINFORCEMENT LH


    C205667
  1. Install the cowl body mounting reinforcement LH with the 3 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



17. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

HINT:
Refer to the procedure from Install Windshield Wiper Motor and Link Assembly .



18. INSTALL FRONT WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



19. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

HINT:
Inspect and adjust the front wheel alignment (Click here).