FRONT WHEEL ALIGNMENT > ADJUSTMENT |
| 1. INSPECT TIRES |
| 2. MEASURE VEHICLE HEIGHT |
![]() |
Bounce the vehicle up and down at the corners to stabilize the suspension.
Measure the vehicle height.
| Tire Size | Front C - A | Rear D - B |
| 195/65R15 | 108 mm (4.25 in.) 90 mm (3.54 in.)* | 26 mm (1.02 in.) 9 mm (0.354 in.)* |
| 215/45R17 | 103 mm (4.06 in.) | 21 mm (0.827 in.) |
| 3. INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION |
![]() |
Install a camber-caster-kingpin gauge and place the front wheels on the center of a wheel alignment tester.
| *1 | Wheel Alignment Tester |
| *2 | Gauge |
Inspect the camber, caster and steering axis inclination.
| Tire Size | Camber Inclination | Right-left Difference |
| 195/65R15 | -0°13' +/- 45' (-0.22° +/- 0.75°) -0°07' +/- 45' (-0.12° +/- 0.75°)* | 45' (0.75°) or less |
| 215/45R17 | -0°12' +/- 45' (-0.20° +/- 0.75°) |
| Tire Size | Caster Inclination | Right-left Difference |
| 195/65R15 | 5°53' +/- 45' (5.88° +/- 0.75°) 5°40' +/- 45' (5.67° +/- 0.75°)* | 45' (0.75°) or less |
| 215/45R17 | 5°50' +/- 45' (5.83° +/- 0.75°) |
| Tire Size | Steering Axis Inclination |
| 195/65R15 | 12°16' (12.27°) 11°52' (11.87°)* |
| 215/45R17 | 12°10' (12.17°) |
| 4. ADJUST CAMBER |
Remove the front wheel.
![]() |
Loosen the 2 nuts.
Clean the installation surfaces of the front shock absorber and the steering knuckle.
Temporarily install the 2 nuts. (Step A)
![]() |
Fully push or pull the front axle hub in the direction of the required adjustment. (Step B)
![]() |
Tighten the nuts.
Install the front wheel.
![]() ![]() ![]() |
Check the camber.
If the measured value is not within the specification, calculate the required adjustment amount using the formula below.
Camber adjustment amount = center of the specified range - measured value
Check the combination of the installed bolts. Select appropriate bolts from the tables below to adjust the camber to the specified values.
| Move the axle hub toward (+) in step B | Move the axle hub toward (-) in step B |
| Refer to table (1) (Move the axle hub toward the positive side) | Refer to table (2) (Move the axle hub toward the negative side) |
Repeat the steps mentioned above. In Step A, replace 1 or 2 selected bolts.
| 5. INSPECT TOE-IN |
Bounce the vehicle up and down at the corners to stabilize the suspension.
Release the parking brake and move the shift lever to N.
Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step C)
![]() |
Put tread center marks on the rearmost points of the front wheels and measure the distance between the marks (dimension B).
| *1 | Tread Center Mark |
| *2 | Dimension B |
Slowly push the vehicle straight ahead to cause the front wheels to rotate 180° using the front tire valve as a reference point.
![]() |
Measure the distance between the tread center marks on the front side of the wheels (dimension A).
| *1 | Front of the Vehicle |
| *2 | Dimension A |
| Specified Condition |
| C + D: 0°12' +/- 0°12' (0.20° +/- 0.20°) C + D: 0°18' +/- 0°12' (0.30° +/- 0.20°)* |
| B - A: 2.0 +/- 2.0 mm (0.0787 +/- 0.0787 in.) B - A: 3.0 +/- 2.0 mm (0.118 +/- 0.0787 in.)* |
| 6. ADJUST TOE-IN |
![]() |
Make sure that the thread length of the right and left rack ends are approximately the same.
| *1 | Thread Length |
Remove the boot clips.
![]() |
Loosen the tie rod end lock nuts.
| *1 | Loosen |
| *2 | Turn |
Adjust the rack ends if the difference in thread length between the right and left rack ends is not within the specified range.
Extend the shorter rack end if the measured toe-in deviates toward the outer-side.
Shorten the longer rack end if the measured toe-in deviates toward the inner-side.
Turn the right and left rack ends by an equal amount to adjust the toe-in to the center value.
Make sure that the thread lengths of the right and left rack ends are the same.
Tighten the tie rod end lock nuts.
Place the boots on the seats and install the clips.
| 7. INSPECT WHEEL ANGLE |
![]() |
| *1 | Front of the Vehicle |
| *2 | Inside |
| *3 | Outside |
Put tread center marks on the rearmost points of a turning radius gauge.
Turn the steering wheel to the left and right full lock positions, and measure the turning angle.
| Tire Size | Inside Wheel | Outside Wheel Reference |
| 195/65R15 | 40°50' +/- 2° (40.83° +/- 2°) 37°42' +/- 2° (37.70° +/- 2°)* | 33°50' (33.83°) 32°13' (32.22°)* |
| 215/45R17 | 37°27' +/- 2° (37.45° +/- 2°) | 31°56' (31.93°) |
| 8. PLACE FRONT WHEELS FACING STRAIGHT AHEAD |
| 9. PERFORM YAW RATE AND ACCELERATION SENSOR CALIBRATION |
| 10. PERFORM INITIALIZATION (w/ Height Control Sensor) |