Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM

DTC    P0106    Manifold Absolute Pressure / Barometric Pressure Circuit Range / Performance Problem

for Preparation Click here


DESCRIPTION

The manifold absolute pressure sensor detects the intake manifold pressure as a voltage using a built-in sensor. The ECM calculates intake manifold pressure based on this voltage and also calculates the EGR valve and purge VSV opening amount according to changes in the intake manifold pressure.
A263608E01

DTC No.
DTC Detection Condition
Trouble Area
P0106
Intake manifold pressure measured after engine start drops by less than 3 kPa (22.5 mmHg) compared to the intake manifold pressure (atmospheric pressure) measured before engine start (2 trip detection logic).
  1. Intake system
  2. Manifold absolute pressure sensor

MONITOR DESCRIPTION

When the intake manifold pressure measured after engine start drops by less than 3 kPa (22.5 mmHg) compared to the intake manifold pressure (atmospheric pressure) measured before engine start, the ECM interprets this as a malfunction in the manifold absolute pressure sensor and stores the DTC.

MONITOR STRATEGY


Related DTCs
P0106: Manifold absolute pressure sensor stuck
Required Sensor/Components (Main)
Manifold absolute pressure sensor
Required Sensor/Components (Related)
-
Frequency of Operation
Continuous
Duration
6 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs are not present
P0010 (Camshaft timing oil control valve assembly bank 1)
P0011 (VVT system bank 1 - advance)
P0012 (VVT system bank 1 - retard)
P0016 (VVT system bank 1 - misalignment)
P0107, P0108 (Manifold absolute pressure)
P0112, P0113 (Intake air temperature sensor)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0335 (Crankshaft position sensor)
P0401 (EGR system (closed))
P106A (Evaporative emission control system pressure sensor - manifold pressure sensor correlation)
Auxiliary battery voltage
10.5 V or more
Engine coolant temperature
30°C (86°F) or more
Intake air temperature
-10°C (14°F) or more
Engine speed
1000 rpm or more
Throttle valve
Close
EGR valve
Close
Atmospheric pressure
76 kPa(abs) [570 mmHg(abs)] or more

TYPICAL MALFUNCTION THRESHOLDS


Difference between manifold absolute pressure sensor and atmospheric pressure
More than -3 kPa (-22.5 mmHg)

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the power switch on (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the power switch off and wait for at least 30 seconds.
  5. Turn the power switch on (IG) and turn the Techstream on.
  6. Put the engine in inspection mode (maintenance mode) (Click here).
  7. Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.
  8. Move the shift lever to N.
  9. Idle the engine for 10 seconds or more [A].
  10. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
  11. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  12. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  13. Input the DTC: P0106.
  14. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again.

  15. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTC OUTPUT (IN ADDITION TO DTC P0106)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG) and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0106 is output
    A
    DTC P0106 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0106 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.READ VALUE USING TECHSTREAM (MANIFOLD ABSOLUTE PRESSURE SENSOR)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG) and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / MAP.

  1. Read the MAP value at power switch on (IG).

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Start the engine and warm it up.

  1. Read the MAP value at idling.

    Standard:

    Engine condition
    Techstream Display
    Power switch on (IG)
    80 to 110 kPa(abs) [600 or 825 mmHg(abs)]
    Idling
    28 to 48 kPa(abs) [210 to 360 mmHg(abs)]



NG
Go to step 3
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

3.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leaks (Click here).

    OK:
    No leaks in the intake system.

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the intake system (Click here).



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK

REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR (Click here)