SFI SYSTEM > DATA LIST / ACTIVE TEST |
| DATA LIST |
Warm up the engine.
Turn the power switch off.
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the Techstream, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Vehicle Speed | Vehicle speed: Min.: 0 mph (0 km/h), Max.: 159 mph (255 km/h) | Actual vehicle speed | Speed indicated on speedometer |
| Engine Speed | Engine speed: Min.: 0 rpm, Max.: 16383 rpm | 950 to 1050 rpm: Idling | - |
| Calculate Load | Calculated load by ECM: Min.: 0%, Max.: 100% |
| - |
| Vehicle Load | Vehicle load: Min.: 0%, Max.: 25700% | Actual vehicle load | Load percentage in terms of maximum intake air flow amount |
| MAF | Air flow rate from mass air flow meter sub-assembly: Min.: 0 gm/sec, Max.: 655.35 gm/sec | 1 to 3 gm/sec: Idling 4.5 to 8.5 gm/sec: Running without load (2500 rpm) | If value approximately 0.0 gm/sec:
|
| Atmosphere Pressure | Atmospheric pressure: Min.: 0 kPa (0 mmHg, 0 in.Hg) , Max.: 255 kPa (1912 mmHg, 75 in.Hg) | Equivalent to atmospheric pressure | - |
| MAP | Intake manifold pressure: Min.: 0 kPa (0 mmHg, 0 in.Hg) , Max.: 255 kPa (1912 mmHg, 75 in.Hg) |
| - |
| Coolant Temp | Engine coolant temperature: Min.: -40°C (-40°F), Max.: 140°C (284°F) | 75 to 100°C (167 to 212°F): After warming up |
|
| Intake Air | Intake air temperature: Min.: -40°C (-40°F), Max.: 140°C (284°F) | Equivalent to ambient air temperature |
|
| Engine Run Time | Engine run time: Min.: 0 s (seconds), Max.: 65535 s (seconds) | Time after power switch on (READY) |
|
| Initial Engine Coolant Temp | Initial engine coolant temperature: Min.: -40°C (-40°F), Max.: 119.3°C (246.8°F) | - | - |
| Initial Intake Air Temp | Initial intake air temperature: Min.: -40°C (-40°F), Max.: 119.3°C (246.8°F) | - | - |
| Battery Voltage | Auxiliary battery voltage: Min.: 0 V, Max.: 65.535 V | 11 to 16 V: Power switch on (IG) | - |
| Throttle Sensor Volt % | Throttle valve opening percentage according to throttle position sensor: Min.: 0%, Max.: 100% | 10 to 22%: Accelerator pedal fully released | Value calculated based on the voltage at terminal VTA1 |
| Throttl Sensor #2 Volt % | Throttle valve opening percentage according to throttle position sensor No. 2: Min.: 0%, Max.: 100% | 42 to 62%: Accelerator pedal fully released | Value calculated based on the voltage at terminal VTA2 |
| System Guard | System guard: ON or OFF | ON | - |
| Throttle Idle Position | Whether or not throttle position sensor detecting idling: ON or OFF | ON: Idling (inspection mode) |
|
| Throttle Require Position | Required throttle position: Min.: 0 V, Max.: 4.98 V | 0.5 to 1.1 V: Idling | - |
| Throttle Sensor Position*1 | Throttle sensor position: Min.: 0%, Max.: 100% | - | Recognition value for throttle opening angle on ECM |
| Throttle Position No. 1 | Throttle position sensor No. 1 output voltage: Min.: 0 V, Max.: 4.98 V |
| - |
| Throttle Position No. 2 | Throttle position sensor No. 2 output voltage: Min.: 0 V, Max.: 4.98 V |
| - |
| Throttle Position Command | Throttle position command value: Min.: 0 V, Max.: 4.98 V | 0.5 to 1.1 V: Idling | - |
| Throttle Sens Open Pos #1 | Throttle sensor opener position No. 1: Min.: 0 V, Max.: 4.98 V | 0.6 to 1.4 V | - |
| Throttle Sens Open Pos #2 | Throttle sensor opener position No. 2: Min.: 0 V, Max.: 4.98 V | 1.7 to 2.5 V | - |
| Throttle Motor Current | Throttle actuator current: Min.: 0 A, Max.: 19.9 A | 0 to 3.0 A: Idling | - |
| Throttle Motor DUTY | Throttle actuator: Min.: 0%, Max.: 100% | 10 to 22%: Idling after engine warmed up | - |
| Throttle Motor Duty (Open) | Throttle actuator duty ratio (open): Min.: 0%, Max.: 255% | 0 to 40%: Idling | - |
| Throttle Motor Duty (Close) | Throttle actuator duty ratio (close): Min.: 0%, Max.: 255% | 0 to 40%: Idling | - |
| Throttle Fully Close Learn | Throttle valve fully closed (learned value): Min.: 0 V, Max.: 4.98 V | 0.4 to 1.0 V: Accelerator pedal fully released | - |
| +BM Voltage | +BM voltage: Min.: 0, Max.: 79.998 V | 11 to 16 V: Power switch on (IG) and system normal | - |
| Actuator Power Supply | Actuator power supply ON or OFF | ON: Idling | - |
| Injector (Port) | Injection duration for cylinder 1: Min.: 0 μs, Max.: 65535 μs | 1000 to 3000 μs: Idling | - |
| Injection Volum (Cylinder1) | Injection volume (Cylinder 1): Min.: 0 ml, Max.: 2.047 ml | 0.03 to 0.13 ml: Idling | Quantity of fuel injection volume for 10 times |
| Fuel Pump/Speed Status | Fuel pump status: ON or OFF | - | - |
| Vacuum Pump | Key-off EVAP system leak detection pump status: ON or OFF | - | - |
| EVAP (Purge) VSV | Purge VSV control duty: Min.: 0%, Max.: 100% | 0 to 50%: Idling, under purge control | Order signal from ECM |
| Evap Purge Flow | Ratio of evaporative purge flow to intake air volume: Min.: 0%, Max.: 399.9% | 0 to 10%: Idling | - |
| Purge Density Learn Value | Learning value of purge density: Min.: -200, Max.: 199.993 | -40 to 10: Idling | - |
| Vapor Pressure Pump | Vapor pressure: Min.: 0 kPa (0 mmHg, 0 in.Hg), Max.: 1441.77 kPa (10814.168 mmHg, 426 in. Hg) | Approximately 100 kPa(abs) (750 mmHg(abs), 30 in.Hg): Power switch on (IG) | EVAP system pressure monitored by canister pressure sensor |
| Vapor Pressure (Calculated) | Vapor pressure (calculated): Min.: -720.896 kPa (-5407.166 mmHg, -212 in.Hg), Max.: 720.874 kPa (5407.002 mmHg, 213 in.Hg) | Approximately 100 kPa(abs) (750 mmHg(abs), 30 in.Hg): Power switch on (IG) | EVAP system pressure monitored by canister pressure sensor |
| EVAP System Vent Valve | Key-off EVAP system vent valve status: ON or OFF | OFF: Vent ON: Closed | - |
| EVAP Purge VSV | Purge VSV status for EVAP control: ON or OFF | - | - |
| Purge Cut VSV Duty | Purge VSV duty: Min.: 0%, Max.: 399.9% | - | - |
| Target Air-Fuel Ratio | Target air fuel ratio: Min.: 0, Max.: 1.99 | 0.8 to 1.2: Idling | - |
| AF Lambda B1S1 | Short-term fuel trim associated with bank 1 sensor 1: Min.: 0, Max.: 1.99 |
| - |
| AFS Voltage B1S1 | Air fuel ratio sensor output voltage for bank 1 sensor 1: Min.: 0 V, Max.: 7.99 V | 2.6 to 3.8 V: Idling after engine warmed up | Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensors |
| AFS Current B1S1 | Air fuel ratio sensor output current for bank 1 sensor 1: Min.: -128 mA, Max.: 127.99 mA | -0.5 to 0.5 mA: Idling after engine warmed up | Value becomes higher when fuel-cut executed under high engine speed |
| A/F Heater Duty #1 | Air fuel ratio heater duty ratio for bank 1: Min.: 0%, Max.: 399.9% | 0 to 100% | - |
| O2S B1S2 | Heated oxygen sensor output voltage for bank 1 sensor 2: Min.: 0 V, Max.: 1.275 V | 0.0 to 0.9 V: Driving at 44 mph (70 km/h) | Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensors |
| O2S Impedance B1S2 | Heated oxygen sensor impedance (bank 1 sensor 2): Min.: 0 ohm, Max.: 21247.67 ohm | 5 to 15000 ohm: After driving for 10 minutes or more in urban area | - |
| O2 Heater B1S2 | Heated oxygen sensor heater for bank 1 sensor 2: Not Act or Active | - | - |
| O2 Heater Curr Val B1S2 | Heated oxygen sensor current for bank 1 sensor 2: Min.: 0 A, Max.: 4.999 A | - | - |
| Short FT #1 | Short-term fuel trim of bank 1: Min.: -100%, Max.: 99.2% | -20 to 20% | Short-term fuel compensation used to maintain air fuel ratio at stoichiometric air fuel ratio |
| Long FT #1 | Long-term fuel trim of bank 1: Min.: -100%, Max.: 99.2% | -20 to 20% |
|
| A/F Learn Value Idle #1 | Air fuel ratio learn value of idle area (Bank 1): Min.: -50%, Max.: 49.6% | -20 to 20% | Learning is performed when idling with the engine warmed up (engine coolant temperature is 80°C [176°F] or more) |
| A/F Learn Value Low #1 | Air fuel ratio learn value of low load area (Bank 1): Min.: -50%, Max.: 49.6% | -20 to 20% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or more) and operating in the low load range (when the range of engine loads is divided into four parts) |
| A/F Learn Value Mid1 #1 | Air fuel ratio learn value of middle 1 load area (Bank 1): Min.: -50%, Max.: 49.6% | -20 to 20% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or more) and operating in the mid-size load range closer to the low load range (when the range of engine loads is divided into four parts) |
| A/F Learn Value Mid2 #1 | Air fuel ratio learn value of middle 2 load area (Bank 1): Min.: -50%, Max.: 49.6% | -20 to 20% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or more) and operating in the mid-size load range closer to the high load range (when the range of engine loads is divided into four parts) |
| A/F Learn Value High #1 | Air fuel ratio learn value of high load area (Bank 1): Min.: -50%, Max.: 49.6% | -20 to 20% | Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or more) and operating in the high load range (when the range of engine loads is divided into four parts) |
| Total FT #1 | Average value for fuel trim system of bank 1: Min.: -0.5, Max.: 0.496 | -0.28 to 0.2: Idling | - |
| Fuel System Status #1 | Fuel system status (bank 1): OL, CL, OLDrive, OLFault, CLFault or Unused | CL: Idling after warming up |
|
| Fuel System Status #2 | Fuel system status (bank 2): OL, CL, OLDrive, OLFault, CLFault or Unused | Unused | - |
| IGN Advance | Ignition timing advance for No. 1 cylinder: Min.: -64 deg., Max.: 63.5 deg. | 0 to 16 deg.: Idling | - |
| Knock Feedback Value | Feedback value of knocking: Min.: -1024 dag(CA), Max.: 1023.9 dag(CA) | -20 to 0 dag(CA): Driving at 44 mph (70 km/h) | - |
| Knock Correct Learn Value | Correction learning value of knocking: Min.: -1024 dag(CA), Max.: 1023.9 dag(CA) | 0 to 22 dag(CA): Driving at 44 mph (70 km/h) | - |
| Target EGR Position | Target EGR position: Min.: 0%, Max.: 100% | 0%: Idling | - |
| EGR Step Position | EGR step position: Min.: 0 step, Max.: 255 step | 0 step: Idling | - |
| VVT Control Status #1 | VVT control (bank 1) status: ON or OFF | - | - |
| VVT Aim Angle #1*2 | VVT hold duty learned value (bank 1): Min.: 0%, Max.: 399.9% | - | VVT duty signal value during intrusive operation |
| VVT Change Angle #1*2 | VVT displacement angle (bank 1): Min.: 0 DegFR, Max.: 639.9 DegFR | - | Displacement angle during intrusive operation |
| VVT OCV Duty #1*2 | VVT camshaft timing oil control valve assembly operation duty: Min.: 0%, Max.: 399.9% | - | Requested duty value for intrusive operation |
| VN Turbo Type | Variable nozzle turbo type: Not Avl or Commo or Vacuum or CAN Com | Not Avl (Unused) | - |
| Catalyst Temp B1S1 | Catalyst temperature (associated with sensor 1): Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F) | - | - |
| Catalyst Temp B1S2 | Catalyst temperature (associated with sensor 2): Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F) | - | - |
| Closed Throttle Position SW | Closed throttle position switch: ON or OFF | - | - |
| Fuel Cut Condition | Fuel cut determination: ON or OFF | ON: Fuel cut operating or engine stopped | - |
| Check Mode | Check mode: ON or OFF | ON: Check mode ON | (Click here) |
| Misfire Test Result | Check mode result for misfire monitor: Compl or Incmpl | - | - |
| OXS1 Test Result | Check mode result for heated oxygen sensor (bank 1): Compl or Incmpl | - | - |
| A/F Test Results #1 | Check mode result for air fuel ratio sensor (bank 1) Compl or Incmpl | - | - |
| Complete Parts Monitor | Comprehensive component monitor: Not Avl or Avail | - | - |
| Fuel System Monitor | Fuel system monitor: Not Avl or Avail | - | - |
| Misfire Monitor | Misfire monitor: Not Avl or Avail | - | - |
| EGR/VVT Monitor | EGR monitor: Not Avl or Avail | - | - |
| EGR/VVT Monitor | EGR monitor: Compl or Incmpl | - | - |
| O2S(A/FS) Heater Monitor | O2S (A/FS) heater monitor: Not Avl or Avail | - | - |
| O2S(A/FS) Heater Monitor | O2S (A/FS) heater monitor: Compl or Incmpl | - | - |
| O2S(A/FS) Monitor | O2S (A/FS) monitor: Not Avl or Avail | - | - |
| O2S(A/FS) Monitor | O2S (A/FS) monitor: Compl or Incmpl | - | - |
| A/C Monitor | A/C monitor: Not Avl or Avail | - | - |
| A/C Monitor | A/C monitor: Compl or Incmpl | - | - |
| 2nd Air Monitor | 2nd air monitor: Not Avl or Avail | - | - |
| 2nd Air Monitor | 2nd air monitor: Compl or Incmpl | - | - |
| EVAP Monitor | EVAP monitor: Not Avl or Avail | - | - |
| EVAP Monitor | EVAP monitor: Compl or Incmpl | - | - |
| Heated Catalyst Monitor | Heated catalyst monitor: Not Avl or Avail | - | - |
| Heated Catalyst Monitor | Heated catalyst monitor: Compl or Incmpl | - | - |
| Catalyst Monitor | Catalyst monitor: Not Avl or Avail | - | - |
| Catalyst Monitor | Catalyst monitor: Compl or Incmpl | - | - |
| Component Monitor ENA | Comprehensive component monitor: Unable or Enable | - | - |
| Component Monitor CMPL | Comprehensive component monitor: Compl or Incmpl | - | - |
| Fuel System Monitor ENA | Fuel system monitor: Unable or Enable | - | - |
| Fuel System Monitor CMPL | Fuel system monitor: Compl or Incmpl | - | - |
| Misfire Monitor ENA | Misfire monitor: Unable or Enable | - | - |
| Misfire Monitor CMPL | Misfire monitor: Compl or Incmpl | - | - |
| EGR/VVT Monitor ENA | EGR monitor: Unable or Enable | - | - |
| EGR/VVT Monitor CMPL | EGR monitor: Compl or Incmpl | - | - |
| Heater Monitor ENA | O2S (A/FS) heater monitor: Unable or Enable | - | - |
| Heater Monitor CMPL | O2S (A/FS) heater monitor: Compl or Incmpl | - | - |
| O2S(A/FS) Monitor ENA | O2S (A/FS) monitor: Unable or Enable | - | - |
| O2S(A/FS) Monitor CMPL | O2S (A/FS) monitor: Compl or Incmpl | - | - |
| A/C Monitor ENA | A/C monitor: Unable or Enable | - | - |
| A/C Monitor CMPL | A/C monitor: Compl or Incmpl | - | - |
| 2nd Air Monitor ENA | 2nd air monitor: Unable or Enable | - | - |
| 2nd Air Monitor CMPL | 2nd air monitor: Compl or Incmpl | - | - |
| EVAP Monitor ENA | EVAP monitor: Unable or Enable | - | - |
| EVAP Monitor CMPL | EVAP monitor: Compl or Incmpl | - | - |
| Heated Cat Monitor ENA | Heated catalyst monitor: Unable or Enable | - | - |
| Heated Cat Monitor CMPL | Heated catalyst monitor: Compl or Incmpl | - | - |
| Catalyst Monitor ENA | Catalyst monitor: Unable or Enable | - | - |
| Catalyst Monitor CMPL | Catalyst monitor: Compl or Incmpl | - | - |
| TC Terminal | TC terminal status: ON or OFF | - | - |
| # Codes (Include History) | Number of codes: Min.: 0 Max.: 255 | 0: No emission related DTC detected | - |
| MIL | MIL status: ON or OFF | ON: MIL ON | - |
| MIL ON Run Distance | Distance traveled since MIL turned ON: Min.: 0 mile (0 km), Max.: 40724 mile (65535 km) | Distance since DTC detected | - |
| Running Time from MIL ON | Running time since MIL turned ON: Min.: 0 min, Max.: 65535 min | Equivalent to running time since MIL turned on | - |
| Time after DTC Cleared | Time since DTCs cleared: Min.: 0 min, Max.: 65535 min | Equivalent to time since DTCs cleared | - |
| Distance from DTC Cleared | Distance traveled since DTCs cleared: Min.: 0 mile (0 km), Max.: 40724 mile (65535 km) | Equivalent to distance driven since DTCs cleared | - |
| Warmup Cycle Cleared DTC | Warm-up cycles since DTCs cleared: Min.: 0, Max.: 255 | - | Number of warm-up cycles since DTCs cleared |
| Dist Batt Cable Disconnect | Distance from auxiliary battery cable disconnected: Min.: 0 mile (0 km), Max.: 40724 mile (65535 km) | - | - |
| IG OFF Elapsed Time | Time after power switch off: Min.: 0 min, Max.: 655350 min | - | - |
| OBD Requirements | OBD requirement | OBD2 (California ARB) | - |
| Number of Emission DTC | Emission related DTCs Min.: 0 Max.: 127 | - | Number of emission related DTCs |
| TC and TE1 | TC and CG (TE1) terminals of DLC3: ON or OFF | - | - |
| Ignition Trig. Count | Ignition counter: Min.: 0, Max.: 65535 | 0 to 400 | - |
| Cylinder #1 Misfire Count | Misfire count of cylinder 1: Min.: 0, Max.: 255 | 0 | - |
| Cylinder #2 Misfire Count | Misfire count of cylinder 2: Min.: 0, Max.: 255 | 0 | - |
| Cylinder #3 Misfire Count | Misfire count of cylinder 3: Min.: 0, Max.: 255 | 0 | - |
| Cylinder #4 Misfire Count | Misfire count of cylinder 4: Min.: 0, Max.: 255 | 0 | - |
| All Cylinders Misfire Count | All cylinders misfire count: Min.: 0, Max.: 255 | 0 | - |
| Misfire RPM | Average engine speed for first misfire range: Min.: 0 rpm, Max.: 6375 rpm | 0 rpm: 0 Misfire | - |
| Misfire Load | Average engine load for first misfire range: Min.: 0 g/rev, Max.: 3.98 g/rev | 0 g/rev: 0 Misfire | - |
| Misfire Margin | Misfire monitoring: Min.: -128%, Max.: 127% | 0 to 127%: Idling | Misfire detecting margin |
| Electric Fan Motor | Electric cooling fan motor: ON or OFF | - | - |
| Idle Fuel Cut | Fuel cut idle: ON or OFF | ON: Fuel cut operating | - |
| FC TAU | Fuel cut TAU (Fuel cut with very light load): ON or OFF | ON: Fuel cut operating | Fuel cut being performed during very light load to prevent incomplete engine combustion |
| Communication with HV | Status of communication with the power management control ECU: Comm or No Comm | Comm: Power switch on (IG) | - |
| Communication with Brake | Status of communication with the skid control ECU: Comm or No Comm | Comm: Power switch on (IG) | - |
| Comm with Air Conditioner | Status of communication with the air conditioning amplifier assembly: Comm or No Comm | Comm: Power switch on (IG) | - |
| Model Code | Model code | - | Identifies model code: ZVW3## |
| Engine Type | Engine type | - | Identifies engine type: 2ZRFXE |
| Cylinder Number | Cylinder number: Min.: 0, Max.: 255 | - | Identifies number of cylinders: 4 |
| Destination | Destination | - | Identifies destination: A (America) |
| Model Year | Model year: Min.: 1900, Max.: 2155 | - | Identifies model year: 2014 |
| System Identification | System identification | - | Identifies engine system: HV (Hybrid) |
| Engine Speed of Cyl #1 | Engine speed for cylinder 1: Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression performed using Active Test 51199 rpm: Active Test not performed |
| Engine Speed of Cyl #2 | Engine speed for cylinder 2: Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression performed using Active Test 51199 rpm: Active Test not performed |
| Engine Speed of Cyl #3 | Engine speed for cylinder 3: Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression performed using Active Test 51199 rpm: Active Test not performed |
| Engine Speed of Cyl #4 | Engine speed for cylinder 4: Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression performed using Active Test 51199 rpm: Active Test not performed |
| Av Engine Speed of All Cyl | Engine speed for all cylinders: Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression performed using Active Test 51199 rpm: Active Test not performed |
| A/F Sensor Determination (worst value) #1 | Worst judgment value of air fuel ratio sensor output (Bank 1): Min.: -1, Max.: 0.99 | 0 to 0.04 | - |
| Engine Speed Fluctuation Avg (worst value) #1 | Worst value of average engine speed fluctuation (Cylinder 1): Min.: 0, Max.: 2.55 | 0 to 1.0 | - |
| Engine Speed Fluctuation Avg (worst value) #2 | Worst value of average engine speed fluctuation (Cylinder 2): Min.: 0, Max.: 2.55 | 0 to 1.0 | - |
| Engine Speed Fluctuation Avg (worst value) #3 | Worst value of average engine speed fluctuation (Cylinder 3): Min.: 0, Max.: 2.55 | 0 to 1.0 | - |
| Engine Speed Fluctuation Avg (worst value) #4 | Worst value of average engine speed fluctuation (Cylinder 4): Min.: 0, Max.: 2.55 | 0 to 1.0 | - |
| Sports Mode Switch | Pattern select switch status: ON or OFF | ON: Pattern select switch on | - |
| Requested Engine Torque | Requested engine torque: Min.: 0 kW, Max.: 16383.75 kW | 0 to 73 kW | Flag information for hybrid vehicle |
| HV Target Engine Speed | Hybrid target engine speed: Min.: 0 rpm, Max.: 6375 rpm | 0 to 5200 rpm | Flag information for hybrid vehicle |
| Actual Engine Torque | Actual engine torque: Min.: -32768 Nm, Max.: 32767 Nm | Actual engine torque | Flag information for hybrid vehicle |
| Engine Run Time | Engine run time: Min.: 0 s (seconds), Max.: 255 s (seconds) | 0 to 255 s | Flag information for hybrid vehicle |
| Request Engine Run Time | Request engine run time: Min.: 0 s (seconds), Max.: 25.5 s (seconds) | 0 to 25.5 s | Flag information for hybrid vehicle |
| Judge Time Engine Ignition | Judgment time for complete explosion of ignition: Min.: 0 s (seconds), Max.: 25.5 s (seconds) | 0 to 25.5 s | Flag information for hybrid vehicle |
| Judge Time Engine Output | Judgment time for time until engine output: Min.: 0 s (seconds), Max.: 25.5 s (seconds) | 0 to 25.5 s | Flag information for hybrid vehicle |
| Fuel Level | Fuel level: Empty or Not Emp | - | Flag information for hybrid vehicle |
| ISC Learning | Idle speed control learning: Compl or Incmpl | - | Flag information for hybrid vehicle |
| F/C for Engine Stop Req | Fuel cut for engine stop request: ON or OFF | - | Flag information for hybrid vehicle |
| Engine Independent | Engine independent operation: Not Opr or Operate | - | Flag information for hybrid vehicle |
| Racing Operation | Racing operation: Not Opr or Operate | - | Flag information for hybrid vehicle |
| Request Warm-up | Request engine warm up: Not Req or Request | - | Flag information for hybrid vehicle |
| Engine Independent Control | Engine independent control operation: Not Opr or Operate | - | Flag information for hybrid vehicle |
| Elec Water Pump Target Spd | Engine water pump assembly target speed Min.: 0 rpm, Max.: 6375 rpm | - | - |
| Elec Water Pump Spd | Engine water pump assembly speed Min.: 0 rpm, Max.: 6375 rpm | - | - |
| ISC Learning Value | Idle speed control learning value: Min.: 0 L/s, Max.: 79.998 L/s | 0.5 to 6.1 L/s | Flag information for hybrid vehicle |
| ACTIVE TEST |
Warm up the engine.
Turn the power switch off.
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the Techstream, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Control the Injection Volume | Change injection volume | Between -12.5% and 24.8% |
|
| Control the Injection Volume for A/F Sensor | Change injection volume | -12.5%/0%/12.5% |
|
| Control the EGR Step Position | Open or close EGR valve | 0 to 110 steps |
|
| Activate the VSV for Evap Control | Activate purge VSV control | ON/OFF |
|
| Control the Fuel Pump / Speed | Activate fuel pump | ON/OFF | Perform this test when the following conditions are met:
|
| Connect the TC and TE1 | Turn on and off TC and TE1 connection | ON/OFF |
|
| Control the Idle Fuel Cut Prohibit | Prohibit idling fuel cut control | ON/OFF |
|
| Control the Electric Cooling Fan | Control electric cooling fan motor | ON/OFF | Perform this test when the following conditions are met:
|
| Control the ETCS Open/Close Slow Speed | Throttle actuator | Close/Open Open: Throttle valve opens slowly | This test is possible when the following conditions are met:
|
| Control the ETCS Open/Close Fast Speed | Throttle actuator | Close/Open Open: Throttle valve opens quickly | Same as above. |
| Control the VVT Linear (Bank 1) | Control camshaft timing oil control valve assembly (bank 1) | -128 to 127% (This value added to present camshaft timing oil control valve control duty) 100%: Maximum advance -100%: Maximum retard |
|
| Control the VVT System (Bank 1) | Turn camshaft timing oil control valve on and off | ON/OFF |
|
| Activate the Vacuum Pump | Activate leak detection pump (built into canister pump module) | ON/OFF | Refer to EVAP system (Click here). |
| Activate the VSV for Vent Valve | Activate vent valve (built into canister pump module) | ON/OFF | Refer to EVAP system (Click here). |
| Control the Select Cylinder Fuel Cut | Selected cylinder (cylinder #1 to #4) injector fuel cut | #1/#2/#3/#4 ON/OFF |
|
| Control the All Cylinders Fuel Cut | Fuel cut for all cylinders | ON/OFF |
|
| Check the Cylinder Compression | Check the cylinder compression pressure | ON/OFF | This active test should be performed in inspection mode (maintenance mode). *1 |
| Activate the Electric Water Pump | Engine water pump assembly speed control | 0/3000 rpm | Test possible when either of the following condition is met:
|
| SYSTEM CHECK |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility.
Perform the System Check by referring to the table below.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Evaporative System Check (Automatic Mode) | Perform 6 steps in order to operate EVAP key-off monitor automatically | 35°C (95°F) or less |
|
| Evaporative System Check (Manual Mode) | Perform 6 steps in order to operate EVAP key-off monitor manually | 35°C (95°F) or less |
|