Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM

DTC    P0112    Intake Air Temperature Circuit Low Input

DTC    P0113    Intake Air Temperature Circuit High Input

for Preparation Click here


DESCRIPTION

Refer to DTC P0111 .

HINT:
When either DTC P0112 or P0113 is stored, the ECM enters fail-safe mode. During fail-safe mode, the intake air temperature is estimated to be 20°C (68°F) by the ECM. Fail-safe mode continues until a pass condition is detected.


DTC No.
DTC Detection Condition
Trouble Area
P0112
Short in intake air temperature sensor circuit for 0.5 seconds
(1 trip detection logic)
  1. Short in intake air temperature sensor circuit
  2. Intake air temperature sensor (built into mass air flow meter sub-assembly)
  3. ECM
P0113
Open in intake air temperature sensor circuit for 0.5 seconds
(1 trip detection logic)
  1. Open in intake air temperature sensor circuit
  2. Intake air temperature sensor (built into mass air flow meter sub-assembly)
  3. ECM

HINT:
When any of these DTCs are stored, check the intake air temperature by entering the following menus: Powertrain / Engine and ECT / Data List / Primary / Intake Air.


Temperature Displayed
Malfunction
-40°C (-40°F)
Open circuit
More than 128°C (262°F)
Short circuit

MONITOR DESCRIPTION

The ECM monitors the sensor voltage and uses this value to calculate the intake air temperature. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the intake air temperature sensor and stores a DTC.
Example:
If the sensor output voltage is more than 4.91 V for 0.5 seconds or more, the ECM determines that there is an open in the intake air temperature sensor circuit, and stores DTC P0113. Conversely, if the output voltage is less than 0.18 V for 0.5 seconds or more, the ECM determines that there is a short in the sensor circuit, and stored DTC P0112.

MONITOR STRATEGY


Related DTCs
P0112: Intake air temperature sensor range check (Low voltage)
P0113: Intake air temperature sensor range check (High voltage)
Required Sensors/Components (Main)
Intake air temperature sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
0.5 seconds
MIL Operation
Immediately
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs are not present
None
Both of the following conditions are met
-
Auxiliary battery voltage
8 V or more
Power switch
On (IG)

TYPICAL MALFUNCTION THRESHOLDS


P0112 
Intake air temperature sensor voltage [Intake air temperature]
Less than 0.18 V [Higher than 128°C (262°F)]

P0113 
Intake air temperature sensor voltage [Intake air temperature]
Higher than 4.91 V [Less than -55°C (-67°F)]

COMPONENT OPERATING RANGE


Intake air temperature sensor voltage [Intake air temperature]
0.18 to 4.91 V [-55 to 128°C (-67 to 262°F)]

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the power switch on (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the power switch off and wait for at least 30 seconds.
  5. Turn the power switch on (IG) and turn the Techstream on.
  6. Wait 0.5 seconds or more.
  7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  8. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  10. Input the DTC: P0112 or P0113.
  11. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  12. If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A220564E01


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.READ VALUE USING TECHSTREAM (INTAKE AIR TEMPERATURE)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Intake Air.

  1. Read the value displayed on the Techstream.

    OK:
    Same as actual intake air temperature.


    Result:

    Result
    Proceed to
    -40°C (-40°F)
    A
    More than 128°C (262°F)
    B
    Same as actual intake air temperature
    C

    HINT:
    1. If there is an open circuit, the Techstream indicates -40°C (-40°F).
    1. If there is a short circuit, the Techstream indicates more than 128°C (262°F).



B
Go to step 4

C
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2.READ VALUE USING TECHSTREAM (CHECK FOR OPEN IN WIRE HARNESS)


  1. Confirm good connection at the mass air flow meter sub-assembly.


    A194099E49


Text in Illustration 
*1
Mass Air Flow Meter Sub-assembly
*2
ECM
*a
Front view of wire harness connector
(to Mass Air Flow Meter Sub-assembly)
-
-
  1. Disconnect the mass air flow meter sub-assembly connector.

  1. Connect terminals 1 (THA) and 2 (E2) of the mass air flow meter sub-assembly connector on the wire harness side.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Intake Air.

  1. Read the value displayed on the Techstream.

    Standard value:
    More than 128°C (262°F)

    HINT:
    Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly (Click here).



NG
Go to step 3
OK

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY (Click here)  

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
  1. Disconnect the mass air flow meter sub-assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    D5-1 (THA) - D28-116 (THA)
    Always
    Below 1 Ω
    D5-2 (E2) - D28-93 (ETHA)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

4.READ VALUE USING TECHSTREAM (CHECK FOR SHORT IN WIRE HARNESS)


    A194323E03
  1. Disconnect the mass air flow meter sub-assembly connector.
    Text in Illustration 
    *1
    Mass Air Flow Meter Sub-assembly
    *2
    ECM

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Intake Air.

  1. Read the value displayed on the Techstream.

    Standard value:
    -40°C (-40°F)

    HINT:
    Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly (Click here).



NG
Go to step 5
OK

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY (Click here)  

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
  1. Disconnect the mass air flow meter sub-assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Short):

    Tester Connection
    Condition
    Specified Condition
    D5-1 (THA) or D28-116 (THA) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)