AIR CONDITIONING SYSTEM > Blower Motor Circuit |
| w/o Solar Ventilation System |

| w/ Solar Ventilation System |

| 1.PERFORM ACTIVE TEST USING TECHSTREAM |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Enter the following menus: Body Electrical / Air Conditioner / Active Test.
Check the operation by referring to the table below.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Blower Motor | Blower motor | Min.: 0, Max.: 31 | - |
| Result | Proceed to |
| OK | A |
| NG (Blower motor does not operate) (w/o Solar ventilation system) | B |
| NG (Blower motor does not operate) (w/ Solar ventilation system) | C |
| NG (Blower motor operates but does not change speed) (w/o Solar ventilation system) | D |
| NG (Blower motor operates but does not change speed) (w/ Solar ventilation system) | E |
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | ||
| ||
| 2.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR - BODY GROUND) |
![]() |
Disconnect the blower motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L33-1 (GND) - Body ground | Always | Below 1 Ω |
| *1 | Front view of wire harness connector (to Blower Motor) |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR - BATTERY) |
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L33-3 (+B) - Body ground | Power switch off | 11 to 14 V |
| *1 | Front view of wire harness connector (to Blower Motor) |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR - A/C AMPLIFIER) |
![]() |
Disconnect the A/C amplifier connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L17-23 (BLW) - L33-2 (SI) | Always | Below 1 Ω |
| L17-23 (BLW) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to A/C Amplifier) |
| *2 | Front view of wire harness connector (to Blower Motor) |
|
| ||||
| OK | |
| 5.INSPECT BLOWER MOTOR |
Reconnect the blower motor connector.
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L17-23 (BLW) - Body ground | Power switch off | 4.5 to 5.5 V |
| *1 | Front view of wire harness connector (to A/C Amplifier) |
|
| ||||
| OK | |
| 6.INSPECT A/C AMPLIFIER |
![]() |
Remove the A/C amplifier.
Reconnect the A/C amplifier connector.
Turn the power switch on (IG).
Set the blower speed to LO.
Measure the waveform between terminal L17-23 (BLW) of the A/C amplifier and body ground.
| Item | Content |
| Tool setting | 1 V/DIV., 500 μs/DIV. |
| Vehicle condition | Power switch on (IG) Blower set to LO |
| *1 | Component with harness connected (A/C Amplifier) |
|
| ||||
| OK | ||
| ||
| 7.INSPECT SOLAR VENTILATION RELAY |
![]() |
Remove the solar ventilation relay from the relay block No. 2-1.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| 3 - 5 | 10 kΩ or higher |
| 3 - 4 | Below 1 Ω |
| 3 - 5 | Below 1 Ω (when battery voltage is applied to terminals 1 and 2) |
| 3 - 4 | 10 kΩ or higher (when battery voltage is applied to terminals 1 and 2) |
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (SOLAR VENTILATION RELAY - BATTERY) |
![]() |
Disconnect the solar ventilation relay connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L104-1 - Body ground | Power switch off | Below 1 V |
| L104-1 - Body ground | Power switch on (IG) | 11 to 14 V |
| L104-5 - Body ground | Always | 11 to 14 V |
| *1 | Front view of wire harness connector (to Solar Ventilation Relay) |
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (SOLAR VENTILATION RELAY - BODY GROUND) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L104-2 - Body ground | Always | Below 1 Ω |
| *1 | Front view of wire harness connector (to Solar Ventilation Relay) |
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR - BODY GROUND) |
![]() |
Disconnect the blower motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L33-1 (GND) - Body ground | Always | Below 1 Ω |
| *1 | Front view of wire harness connector (to Blower Motor) |
|
| ||||
| OK | |
| 11.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR - BATTERY) |
Reinstall the solar ventilation relay.
Reconnect the solar ventilation relay connector.
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L33-3 (+B) - Body ground | Power switch off Solar ventilation switch off | Below 1 V |
| L33-3 (+B) - Body ground | Power switch on (IG) | 11 to 14 V |
| *1 | Front view of wire harness connector (to Blower Motor) |
|
| ||||
| OK | |
| 12.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR - A/C AMPLIFIER, SOLAR VENTILATION ECU) |
![]() |
Disconnect the A/C amplifier connector.
![]() |
Disconnect the solar ventilation ECU connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L17-23 (BLW) - L33-2 (SI) | Always | Below 1 Ω |
| L22-5 (BLW) - L33-2 (SI) | Always | Below 1 Ω |
| L17-23 (BLW) - Body ground | Always | 10 kΩ or higher |
| L22-5 (BLW) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to A/C Amplifier) |
| *2 | Front view of wire harness connector (to Solar Ventilation ECU) |
| *3 | Front view of wire harness connector (to Blower Motor) |
|
| ||||
| OK | |
| 13.INSPECT BLOWER MOTOR |
Reconnect the blower motor connector.
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L17-23 (BLW) - Body ground | Power switch off Solar ventilation switch off | Below 1 V |
| L17-23 (BLW) - Body ground | Power switch on (IG) | 4.5 to 5.5 V |
| *1 | Front view of wire harness connector (to A/C Amplifier) |
|
| ||||
| OK | |
| 14.INSPECT A/C AMPLIFIER |
![]() |
Remove the A/C amplifier.
Reconnect the A/C amplifier connector.
Turn the power switch on (IG).
Set the blower speed to LO.
Measure the waveform between terminal L17-23 (BLW) of the A/C amplifier and body ground.
| Item | Content |
| Tool setting | 1 V/DIV., 500 μs/DIV. |
| Vehicle condition | Power switch on (IG) Blower set to LO |
| *1 | Component with harness connected (A/C Amplifier) |
|
| ||||
| OK | ||
| ||