Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM

DTC    P0340    Camshaft Position Sensor Circuit Malfunction

DTC    P0342    Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor)

DTC    P0343    Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor)

for Preparation Click here


DESCRIPTION

The camshaft position sensor for intake camshaft (G2 signal) consists of a magnet and MRE (Magneto Resistance Element).
The camshaft has a timing rotor for the camshaft position sensor. When the camshaft rotates, changes occur in the air gaps between the timing rotor and MRE, which affects the magnet. As a result, the resistance of the MRE material fluctuates. The camshaft position sensor converts the camshaft rotation data to pulse signals, and uses the pulse signals to determine the camshaft angle, which it sends to the ECM. Then the ECM uses this data to control fuel injection duration, injection timing and VVT system.

DTC No.
DTC Detection Condition
Trouble Area
P0340
When either of following conditions is met:
(1 trip detection logic)
  1. No camshaft position sensor signal to ECM at engine speed 600 rpm or more
  2. Missing camshaft position sensor signal despite crankshaft position sensor inputs normal at engine speed of 600 rpm or more
  1. Open or short in camshaft position sensor circuit
  2. Camshaft position sensor
  3. Intake camshaft
  4. Valve timing
  5. ECM
P0342
Output voltage of camshaft position sensor less than 0.3 V for 4 seconds
(1 trip detection logic)
  1. Open or short in camshaft position sensor circuit
  2. Camshaft position sensor
  3. ECM
P0343
Output voltage of camshaft position sensor more than 4.7 V for 4 seconds
(1 trip detection logic)
  1. Open or short in camshaft position sensor circuit
  2. Camshaft position sensor
  3. ECM
Reference: Inspection using an oscilloscope.
A254147E01
The correct waveform is as shown.
ECM Terminal Name
Between G2+ and G2-
Tester Range
5 V/DIV., 20 ms./DIV.
Condition
Idling with warm engine

MONITOR DESCRIPTION

If no signal is transmitted by the camshaft position sensor despite the engine revolving, or the rotation of the camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction of the sensor.

MONITOR STRATEGY


Related DTCs
P0340: Camshaft position sensor verify pulse input
P0342: Camshaft position sensor range check (Low voltage)
P0343: Camshaft position sensor range check (High voltage)
Required Sensors/Components (Main)
Camshaft position sensor
Required Sensors/Components (Related)
Crankshaft position sensor
Frequency of Operation
Continuous
Duration
5 seconds: Camshaft position sensor verify pulse input
4 seconds: Camshaft position sensor range check (Low voltage, high voltage)
MIL Operation
Immediately
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All 
Monitor runs whenever following DTCs are not present
None

P0340: Camshaft Position Sensor Verify Pulse Input 
All of the following conditions are met
-
Engine speed
600 rpm or more
Starter
OFF
VVT system mis-alignment
Not detected
Camshaft position sensor range check fail (P0342, P0343)
Not detected
Camshaft position sensor voltage
0.3 to 4.7 V
Hybrid control module judge
Engine running
Lost communication of power management control ECU (U0293)
Not detected

P0342 and P0343: Camshaft Position Sensor Range Check (Low Voltage, High Voltage) 
All of the following conditions are met
-
Starter
OFF
Time after power switch off to on (IG)
2 seconds or more
Camshaft position sensor verify pulse input fail (P0340)
Not detected
Auxiliary battery voltage
8 V or more

TYPICAL MALFUNCTION THRESHOLDS


P0340: Camshaft Position Sensor Verify Pulse Input 
Either of the following conditions is met
1 or 2
1. Camshaft position and crankshaft position alignment
Misalignment
2. Camshaft position sensor signal
No signal

P0342: Camshaft Position Sensor Range Check (Low Voltage) 
Camshaft position sensor voltage
Less than 0.3 V

P0343: Camshaft Position Sensor Range Check (High Voltage) 
Camshaft position sensor voltage
More than 4.7 V

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the power switch on (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the power switch off and wait for at least 30 seconds.
  5. Turn the power switch on (IG) and turn the Techstream on.
  6. Put the engine in inspection mode (maintenance mode) (Click here).
  7. Start the engine.
  8. Idle the engine for 10 seconds or more [A].
  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
  10. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P0340, P0342 or P0343.
  13. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again.

  14. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to DTC P0335 .

INSPECTION PROCEDURE

HINT:
  1. If no problem is found through this diagnostic troubleshooting procedure, troubleshoot the engine mechanical system.
  2. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.INSPECT CAMSHAFT POSITION SENSOR (POWER SOURCE)


    A194108E59
  1. Disconnect the camshaft position sensor connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D18-3 (VC) - Body ground
    Power switch on (IG)
    4.5 to 5.0 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Camshaft Position Sensor)



NG
Go to step 9
OK


2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
  1. Disconnect the camshaft position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    D18-1 (VV1+) - D28-76 (G2+)
    Always
    Below 1 Ω
    D18-2 (VV1-) - D28-122 (G2-)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):

    Tester Connection
    Condition
    Specified Condition
    D18-1 (VV1+) or D28-76 (G2+) - Body ground
    Always
    10 kΩ or higher
    D18-2 (VV1-) or D28-122 (G2-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR)


    BR03795E17
  1. Check the camshaft position sensor installation.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR (Click here)
OK


4.INSPECT INTAKE CAMSHAFT (TIMING ROTOR)
  1. Check the timing rotor of the intake camshaft.

    OK:
    Camshaft timing rotor does not have any cracks or deformation.

    HINT:
    Perform "Inspection After Repair" after replacing the intake camshaft (Click here).



NG
REPLACE INTAKE CAMSHAFT (Click here)
OK


5.REPLACE CAMSHAFT POSITION SENSOR
  1. Replace the camshaft position sensor (Click here).


NEXT


6.CHECK WHETHER DTC OUTPUT RECURS (P0340, P0342 OR P0343)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the power switch off and wait for at least 30 seconds.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    DTC P0340, P0342 or P0343 is output
    A
    DTC is not output
    B



B
END
A


7.ADJUST VALVE TIMING
A216026E01

HINT:
There are no marks on the cylinder head to match-up for the purpose of checking valve timing. Valve timing can only be inspected by lining up the colored plates on the timing chain with the marks on the pulleys. It may be necessary to remove and reinstall the chain to match-up the alignment marks (Click here).

Text in Illustration 
*1
Top
*2
Alignment Mark
*3
No. 1 Cylinder at TDC Compression

NEXT


8.CHECK WHETHER DTC OUTPUT RECURS (P0340, P0342 OR P0343)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the power switch off and wait for at least 30 seconds.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    DTC is not output
    A
    DTC P0340, P0342 or P0343 is output
    B

    HINT:
    If the engine does not start, replace the ECM.



B
REPLACE ECM (Click here)
A

END 

9.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
  1. Disconnect the camshaft position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    D18-3 (VC) - D28-99 (VCV1)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):

    Tester Connection
    Condition
    Specified Condition
    D18-3 (VC) or D28-99 (VCV1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)