DTC P014C A/F Sensor Slow Response - Rich to Lean Bank 1 Sensor 1 |
DTC P014D A/F Sensor Slow Response - Lean to Rich Bank 1 Sensor 1 |
DTC P015A A/F Sensor Delayed Response - Rich to Lean Bank 1 Sensor 1 |
DTC P015B A/F Sensor Delayed Response - Lean to Rich Bank 1 Sensor 1 |
| DTC No. | DTC Detection Condition | Trouble Area |
| P014C | The "Rich to Lean response rate deterioration level*" value is standard or less (2 trip detection logic) |
|
| P014D | The "Lean to Rich response rate deterioration level*" value is standard or more (2 trip detection logic) | |
| P015A | The "Rich to Lean delay level*" value is standard or more (2 trip detection logic) | |
| P015B | The "Lean to Rich delay level*" value is standard or more (2 trip detection logic) |

| Related DTCs | P014C: Air fuel ratio sensor (sensor 1) response rate (rich to lean response rate) P014D: Air fuel ratio sensor (sensor 1) response rate (lean to rich response rate) P015A: Air fuel ratio sensor (sensor 1) response rate (rich to lean delay) P015B: Air fuel ratio sensor (sensor 1) response rate (lean to rich delay) |
| Required Sensors/Components (Main) | Air fuel ratio sensor |
| Required Sensors/Components (Related) | Vehicle speed sensor Crankshaft position sensor |
| Frequency of Operation | Once per driving cycle |
| Duration | 10 to 15 seconds |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs are not present | None |
| Active air fuel ratio control | Performing |
| Active air fuel ratio control is performed when the following conditions are met | - |
| Auxiliary battery voltage | 11 V or more |
| Engine coolant temperature | 75°C (167°F) or more |
| Idle | OFF |
| Engine speed | 1000 rpm or more, and less than 4000 rpm |
| Air fuel ratio sensor status | Activated |
| Fuel-cut | OFF |
| Engine load | 10% or more, and less than 70% |
| Catalyst monitor | Not yet |
| Mass air flow | 6 gm/sec or more, and less than 15 gm/sec |
| Rich to Lean Response rate deterioration level | 0.037 V or less |
| Lean to Rich Response rate deterioration level | -0.04 V or more |
| Rich to Lean delay level | 345 msec or more |
| Lean to Rich delay level | 345 msec or more |

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (DTC P014C, P014D, P015A OR P015B) |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P014C, P014D, P015A or P015B is output | A |
| DTC P014C, P014D, P015A or P015B and other DTCs are output | B |
|
| ||||
| A | |
| 2.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
Inspect the air fuel ratio sensor (Click here).
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM) |
Disconnect the air fuel ratio sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D24-1 (HA1A) - D28-18 (HA1A) | Always | Below 1 Ω |
| D24-3 (A1A+) - D28-103 (A1A+) | Always | Below 1 Ω |
| D24-4 (A1A-) - D28-126 (A1A-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| D24-1 (HA1A) or D28-18 (HA1A) - Body ground | Always | 10 kΩ or higher |
| D24-3 (A1A+) or D28-103 (A1A+) - Body ground | Always | 10 kΩ or higher |
| D24-4 (A1A-) or D28-126 (A1A-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.CHECK AIR FUEL RATIO SENSOR |
Check that the proper air fuel ratio sensors are installed to the vehicle.
|
| ||||
| OK | |
| 5.PERFORM CONFIRMATION DRIVING PATTERN |
Drive the vehicle according to the Confirmation Driving Pattern.
| NEXT | |
| 6.CHECK WHETHER DTC OUTPUT RECURS (DTC P014C, P014D, P015A OR P015B) |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
Read the pending DTCs.
| Result | Proceed to |
| DTC P014C, P014D, P015A and/or P015B are output | A |
| DTC is not output | B |
|
| ||||
| A | |
| 7.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 8.PERFORM CONFIRMATION DRIVING PATTERN |
Drive the vehicle according to the Confirmation Driving Pattern.
| NEXT | |
| 9.CHECK WHETHER DTC OUTPUT RECURS (DTC P014C, P014D, P015A OR P015B) |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
Read the pending DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P014C, P014D, P015A and/or P015B are output | B |
|
| ||||
| A | ||
| ||