Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART KEY SYSTEM (for Entry Function)

SMART KEY SYSTEM (for Entry Function) > Front Passenger Side Door Entry Lock Function does not Operate

for Preparation Click here


DESCRIPTION

If the front passenger door entry unlock function operates normally, but its entry lock function does not, this means that the request code from the front passenger door is being output normally. In this case, a malfunction in the lock sensor circuit (from the certification ECU (smart key ECU assembly) to the front door outside handle assembly (lock sensor)) is suspected.

WIRING DIAGRAM


B203515E16


INSPECTION PROCEDURE

NOTICE:
  1. The smart key system (for entry function) uses a LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart key system (for entry function) after confirming that the communication system is functioning properly.
  2. Confirm that another key is not in the cabin.

1.CHECK POWER DOOR LOCK OPERATION
  1. When the door control switch on the master switch assembly is operated, check that the doors unlock and lock according to switch operation (Click here).

    OK:
    Door locks operate normally.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Problem Symptoms Table) (Click here)
OK


2.READ VALUE USING TECHSTREAM (DOOR LOCK POSITION SWITCH)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. Read the Data List according to the display on the Techstream.

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Door Lock Pos
    Front passenger side door lock position switch signal/LOCK or UNLOCK
    LOCK: Front passenger side door locked
    UNLOCK: Front passenger side door unlocked
    -

    OK:
    On the Techstream screen, the display changes between LOCK and UNLOCK as shown in the chart above.



NG
GO TO LIGHTING SYSTEM (Proceed to Door Unlock Detection Switch Circuit) (Click here)
OK


3.READ VALUE USING TECHSTREAM (DOOR OUTSIDE HANDLE)
  1. Enter the following menus: Body Electrical / Smart Key / Data List.

  1. Read the Data List according to the display on the Techstream.

    Smart Key (Certification ECU (Smart Key ECU Assembly)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    P-Door Trigger SW
    Front passenger side door lock switch / ON or OFF
    ON: Entry lock switch pressed
    OFF: Entry lock switch not pressed
    -

    OK:
    On the Techstream screen, the display changes between ON and OFF as shown in the chart above.



NG
Go to step 4
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (Click here)  

4.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU)
  1. Disconnect the certification ECU (smart key ECU assembly) connector.



    B203512E32
  1. Disconnect the front door outside handle assembly (for front passenger side) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L62-19 (TSW2) - z4-1 (TRG+)
    Always
    Below 1 Ω
    L62-19 (TSW2) - Body ground
    Always
    10 kΩ or higher
    z4-1 (TRG+) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Certification ECU (Smart Key ECU Assembly))
    *2
    Front view of wire harness connector
    (to Front Door Outside Handle Assembly (for Front Passenger Side))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (LOCK SENSOR SIGNAL INPUT)
  1. Reconnect the certification ECU (smart key ECU assembly) connector.



  1. Reconnect the front door outside handle assembly (for front passenger side) connector.


    B229638E01

  1. Measure the voltage and check for pulses according to the value(s) in the table below.

    Standard:
    Tester Connection
    Condition
    Specified Condition
    L62-19 (TSW2) - L62-15 (E)
    1. Power switch off
    2. All doors closed
    3. Lock sensor (for front passenger side) not touched
    Pulse generation
    L62-19 (TSW2) - L62-15 (E)
    1. Power switch off
    2. All doors closed
    3. Lock sensor (for front passenger side) touched
    Below 2 V


    Text in Illustration 
    *1
    Component with harness connected
    (Certification ECU (Smart Key ECU Assembly))
    -
    -



NG
REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (for Front Passenger Side) (Click here)
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (Click here)