Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART KEY SYSTEM (for Entry Function)

DTC    B27A8    Open in Outside Luggage Compartment Electrical Key Antenna Circuit

for Preparation Click here


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and sends it to the outside electrical key oscillator (for rear side). To detect the key near the driver door, the outside electrical key oscillator (for rear side) creates a detection area towards the area approximately 1.0 m (3.28 ft.) from the back door.
DTC B27A8 is detected by the certification ECU (smart key ECU assembly) when an open circuit occurs between the certification ECU (smart key ECU assembly) and outside electrical key oscillator (for rear side) terminals (between CLG8 and CLG5, or CG8B and CLGB).

DTC No.
DTC Detection Condition
Trouble Area
B27A8
Open circuit detected between the certification ECU (smart key ECU assembly and outside electrical key oscillator (for rear side) terminals (between CLG8 and CLG5, or CG8B and CLGB).
  1. Outside electrical key oscillator (for rear side)
  2. Certification ECU (smart key ECU assembly)
  3. Wire harness or connector

WIRING DIAGRAM


B203528E06


INSPECTION PROCEDURE

NOTICE:
The smart key system (for entry function) uses a LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart key system (for entry function) after confirming that the communication system is functioning properly.

1.CHECK CONNECTOR CONNECTION CONDITION
  1. Turn the power switch off.

  1. Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and the outside electrical key oscillator (for rear side).

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - OUTSIDE ELECTRICAL KEY OSCILLATOR)
  1. Disconnect the certification ECU (smart key ECU assembly) connector.



    B203523E04
  1. Disconnect the outside electrical key oscillator (for rear side) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L63-19 (CLG8) - R19-1 (CLG5)
    Always
    Below 1 Ω
    L63-20 (CG8B) - R19-2 (CLGB)
    Always
    Below 1 Ω
    L63-19 (CLG8) - Body ground
    Always
    10 kΩ or higher
    L63-20 (CG8B) - Body ground
    Always
    10 kΩ or higher
    R19-1 (CLG5) - Body ground
    Always
    10 kΩ or higher
    R19-2 (CLGB) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Certification ECU (Smart Key ECU Assembly))
    *2
    Front view of wire harness connector
    (to Outside Electrical Key Oscillator (for Rear Side))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT OUTSIDE ELECTRICAL KEY OSCILLATOR


    B203529E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R19-1 (CLG5) - R19-2 (CLGB)
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Outside Electrical Key Oscillator (for Rear Side))



NG
REPLACE OUTSIDE ELECTRICAL KEY OSCILLATOR (Click here)
OK


4.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Replace the certification ECU (smart key ECU assembly) (Click here).


NEXT


5.CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs.

    OK:
    DTC B27A8 is not output.



NG
REPLACE OUTSIDE ELECTRICAL KEY OSCILLATOR (Click here)
OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)