Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM

DTC    B1653/35    Seat Position Airbag Sensor Circuit Malfunction

for Preparation Click here


DESCRIPTION

The seat position airbag sensor circuit consists of the center airbag sensor assembly, front seat inner belt assembly LH and the seat position airbag sensor.
DTC B1653/35 is stored when a malfunction is detected in the seat position airbag sensor circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1653/35
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the seat position airbag sensor circuit.
  2. Front seat inner belt assembly LH malfunction
  3. Seat position airbag sensor malfunction
  4. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Front seat inner belt assembly LH
  3. Seat position airbag sensor
  4. Center airbag sensor assembly

WIRING DIAGRAM


C171073E07


INSPECTION PROCEDURE

1.CHECK CONNECTORS
  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the center airbag sensor assembly, front seat inner belt assembly LH and seat position airbag sensor.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the center airbag sensor assembly, front seat inner belt assembly LH and seat position airbag sensor.

  1. Check that the terminals of connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


2.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (OPEN)


    C171041E13
  1. Connect the connectors to the front seat inner belt assembly LH and floor wire.

  1. Using SST, connect terminals 14 (LSP+) and 13 (LSP-) of connector B.

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting the wire.

SST
09843-18040  
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (LSP+) - 1 (LSP-)
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly
    *3
    Front view of wire harness connector
    (to Center Airbag Sensor Assembly)
    *4
    Connector B
    *5
    Front view of wire harness connector
    (to Seat Position Airbag Sensor)
    *6
    Connector E



NG
Go to step 9
OK


3.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT)


    C171042E05
  1. Disconnect SST from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (LSP+) - 1 (LSP-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly
    *3
    Front view of wire harness connector
    (to Seat Position Airbag Sensor)
    *4
    Connector E



NG
Go to step 10
OK


4.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO B+)


    C171042E05
  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (LSP+) - Body ground
    Power switch on (IG)
    Below 1 V
    1 (LSP-) - Body ground
    Power switch on (IG)
    Below 1 V

    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly
    *3
    Front view of wire harness connector
    (to Seat Position Airbag Sensor)
    *4
    Connector E



NG
Go to step 11
OK


5.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO GROUND)


    C171042E05
  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (LSP+) - Body ground
    Always
    1 MΩ or higher
    1 (LSP-) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly
    *3
    Front view of wire harness connector
    (to Seat Position Airbag Sensor)
    *4
    Connector E



NG
Go to step 12
OK


6.CHECK SEAT POSITION AIRBAG SENSOR


    C203081E03
  1. Connect the connectors to the center airbag sensor assembly and seat position airbag sensor.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the power switch off.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly

    HINT:
    Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.



NG
Go to step 7
OK

USE SIMULATION METHOD TO CHECK (Click here)  

7.REPLACE SEAT POSITION AIRBAG SENSOR
  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

  1. Replace the seat position airbag sensor with a known good part (Click here).

    HINT:
    Perform the following inspection using known good parts from another vehicle if possible.


NEXT


8.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    C203081E03
  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the power switch off.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly

    HINT:
    Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

END 

9.CHECK FLOOR WIRE (OPEN)


  1. Disconnect the floor wire from the front seat inner belt assembly LH.


    C171043E14

    HINT:
    SST has already been inserted into connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R4-4 (LSP+) - R4-3 (LSP-)
    Always
    Below 1 Ω


    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly
    *3
    Front Seat Inner Belt Assembly LH
    *4
    Floor Wire
    *5
    Front view of wire harness connector
    (to Center Airbag Sensor Assembly)
    *6
    Front view of wire harness connector
    (to Front Seat Inner Belt Assembly LH)
    *7
    Connector B
    *8
    Connector C



NG
REPLACE FLOOR WIRE
OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH (Click here)  

10.CHECK FLOOR WIRE (SHORT)
C171044E11
  1. Disconnect the floor wire from the front seat belt inner belt assembly LH.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R4-4 (LSP+) - R4-3 (LSP-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly
    *3
    Front Seat Inner Belt Assembly LH
    *4
    Floor Wire
    *5
    Front view of wire harness connector
    (to Front Seat Inner Belt Assembly LH)
    *6
    Connector C



NG
REPLACE FLOOR WIRE
OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH (Click here)  

11.CHECK FLOOR WIRE (SHORT TO B+)


    C171044E11
  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

  1. Disconnect the floor wire from the front seat inner belt assembly LH.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    R4-4 (LSP+) - Body ground
    Power switch on (IG)
    Below 1 V
    R4-3 (LSP-) - Body ground
    Power switch on (IG)
    Below 1 V

    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly
    *3
    Front Seat Inner Belt Assembly LH
    *4
    Floor Wire
    *5
    Front view of wire harness connector
    (to Front Seat Inner Belt Assembly LH)
    *6
    Connector C



NG
REPLACE FLOOR WIRE
OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH (Click here)  

12.CHECK FLOOR WIRE (SHORT TO GROUND)


    C171044E11
  1. Disconnect the floor wire from the front seat inner belt assembly LH.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R4-4 (LSP+) - Body ground
    Always
    1 MΩ or higher
    R4-3 (LSP-) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Seat Position Airbag Sensor
    *2
    Center Airbag Sensor Assembly
    *3
    Front Seat Inner Belt Assembly LH
    *4
    Floor Wire
    *5
    Front view of wire harness connector
    (to Front Seat Inner Belt Assembly LH)
    *6
    Connector C



NG
REPLACE FLOOR WIRE
OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH (Click here)