Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Navigation ECU Communication Stop Mode

for Preparation Click here


DESCRIPTION


Detection Item
Symptom
Trouble Area
Navigation ECU Communication Stop Mode
  1. "AVN1" is not displayed on the "CAN Bus Check" screen of the Techstream
  2. Applies to Navigation ECU Communication Stop Mode in DTC Combination Table
  1. Navigation ECU sub-assembly branch wire or connector
  2. Power source circuit of navigation ECU sub-assembly
  3. Navigation ECU sub-assembly

WIRING DIAGRAM


C258668E01


INSPECTION PROCEDURE

NOTICE:
  1. Turn the power switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.
  2. Turn the power switch off before inspecting CAN bus wires for a ground short.
  3. After the power switch is turned off, check that the key reminder warning system and light reminder warning system are not operating.
  4. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the power switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
  1. Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

1.CHECK CAN BUS WIRE FOR DISCONNECTION (NAVIGATION ECU SUB-ASSEMBLY BRANCH WIRE)
  1. Turn the power switch off.



    C240580E15
  1. Disconnect the navigation ECU sub-assembly connector.
    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Navigation ECU Sub-assembly)

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    L130-9 (CANH) - L130-10 (CANL)
    Power switch off
    54 to 69 Ω



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY BRANCH WIRE)
OK


2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)


    C241290E16
  1. Measure the voltage according to the value(s) in the table below.
    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Navigation ECU Sub-assembly)

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L127-4 (+B1) - Body ground
    Always
    11 to 14 V
    L127-3 (ACC1) - Body ground
    Power switch on (ACC)
    11 to 14 V
    L130-1 (IG) - Body ground
    Power switch on (IG)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE TERMINAL)
OK


3.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)


    E168564E85
  1. Measure the resistance according to the value(s) in the table below.
    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Navigation ECU Sub-assembly)

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L127-7 (GND1) - Body ground
    Always
    Below 1 Ω

    Result:
    Result
    Proceed to
    OK (for Navigation receiver type)
    A
    OK (for Radio and display type)
    B
    NG
    C



B
REPLACE NAVIGATION ECU SUB-ASSEMBLY (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND TERMINAL)
A

REPLACE NAVIGATION ECU SUB-ASSEMBLY (Click here)