Home › Audio / Visual / Telematics › AUDIO / VIDEO › RADIO RECEIVER

RADIO RECEIVER > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
  1. After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).
  2. w/o Daytime Running Light:
    1. A Hard Disk Drive (HDD) is built into the radio and display receiver assembly to store multi-media data, and is used for the audio and visual system. Therefore, care must be taken when handling the radio and display receiver assembly.
    1. When removing the hard disk drive, eliminate static electricity by touching the vehicle body to prevent components from being damaged.



2. REMOVE REAR NO. 2 FLOOR BOARD


    B227787E01
  1. Disengage the 2 guides <A> as shown in the illustration.

  1. Disengage the 3 guides <B> and remove the rear No. 2 floor board.



3. REMOVE REAR DECK FLOOR BOX
  1. Remove the rear deck floor box.



4. REMOVE REAR NO. 3 FLOOR BOARD


    B227791
  1. Disengage the 2 guides and remove the rear No. 3 floor board.



5. DISCONNECT CABLE FROM AUXILIARY BATTERY NEGATIVE TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



6. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY


    B223452E01
  1. Using a moulding remover, slightly lift the panel at the position shown in the illustration.
    Text in Illustration 
    *a
    Lift slightly

  1. Pull the integration control and panel assembly in the direction indicated by the arrow to disengage the 6 claws.

  1. Disconnect each connector and remove the integration control and panel assembly.



7. REMOVE LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    B223454
  1. Pull the lower center instrument cluster finish panel sub-assembly in the direction indicated by the arrow to disengage the 2 claws and 2 clips.



    B223455
  1. Pull the lower center instrument cluster finish panel sub-assembly in the direction indicated by the arrow to disengage the 5 claws and remove the lower center instrument cluster finish panel sub-assembly.



8. REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH
  1. Disengage the 14 claws.



  1. Disconnect the connector and remove the instrument cluster finish panel garnish.


    B223458



9. REMOVE UPPER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    B223459
  1. Disengage the 3 claws.

  1. Disconnect the connector and remove the upper instrument panel finish panel sub-assembly.



10. REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (w/ Daytime Running Light)


    E240852
  1. Remove the 4 bolts.



    E240853
  1. Disengage the 4 claws as shown in the illustration.

  1. Disconnect each connector and remove the radio and display receiver assembly with bracket.



11. REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (w/o Daytime Running Light)


    E188505
  1. Remove the 4 bolts.



    E188507
  1. Disengage the 4 claws as shown in the illustration.

  1. Disconnect each connector and remove the radio and display receiver assembly with bracket.



12. REMOVE NO. 1 RADIO BRACKET (w/ Daytime Running Light)


  1. w/o Navigation System:



      E237134
    1. Remove the 3 bolts and No. 1 radio bracket.



  1. w/ Navigation System:



      E237136
    1. Remove the 5 bolts and No. 1 radio bracket.



13. REMOVE NO. 2 RADIO BRACKET (w/ Daytime Running Light)


  1. w/o Navigation System:



      E237133
    1. Remove the 3 bolts and No. 2 radio bracket.



  1. w/ Navigation System:



      E237135
    1. Remove the 5 bolts and No. 2 radio bracket.



14. REMOVE NO. 1 RADIO BRACKET (w/o Daytime Running Light)


    E237123
  1. Remove the 4 screws and No. 1 radio bracket.



15. REMOVE NO. 2 RADIO BRACKET (w/o Daytime Running Light)


    E237122
  1. Remove the 4 screws and No. 2 radio bracket.



16. REMOVE EXTENSION MODULE (w/ Daytime Running Light)
w/ Navigation System:


17. REMOVE HARD DISK DRIVE (w/o Daytime Running Light)


    E237127
  1. Remove the 2 screws.

  1. Disengage the 2 guides to remove the cover.



    E237128E01
  1. Using a screwdriver with its tip taped with protective tape, slide the hard disk drive in the direction shown by the arrow to remove it.
    Text in Illustration 
    *1
    Protective Tape



18. REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY (w/ Daytime Running Light)


19. REMOVE NAVIGATION ECU SUB-ASSEMBLY (w/o Daytime Running Light)