Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Audio Receiver Assembly Communication Stop Mode

for Preparation Click here


DESCRIPTION


Detection Item
Symptom
Trouble Area
Audio Receiver Assembly Communication Stop Mode
  1. "AVN1" is not displayed on the "CAN Bus Check" screen of the Techstream
  2. Applies to Audio Receiver Assembly Communication Stop Mode in DTC Combination Table
  1. Radio and display receiver assembly branch wire or connector
  2. Power source circuit of radio and display receiver assembly
  3. Radio and display receiver assembly

WIRING DIAGRAM


C258668E04


C258668E03


INSPECTION PROCEDURE

NOTICE:
  1. Turn the power switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.
  2. Turn the power switch off before inspecting CAN bus wires for a ground short.
  3. After the power switch is turned off, check that the key reminder warning system and light reminder warning system are not operating.
  4. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the power switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
  1. Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

1.CHECK CAN BUS WIRE FOR DISCONNECTION (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH WIRE)
  1. Turn the power switch off.



    C240580E16
  1. Disconnect the radio and display receiver assembly connector.
    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Radio and Display Receiver Assembly)

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    L149-9 (CANH) - L149-10 (CANL)
    Power switch off
    54 to 69 Ω



NG
REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY)
OK


2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)


  1. Measure the voltage according to the value(s) in the table below.


    C277256E01


    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Radio and Display Receiver Assembly)
    *2
    for 6 Speakers
    *3
    for 8 Speakers
    -
    -

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L148-4 (+B1) - Body ground*1
    L138-1 (+B1) - Body ground*2
    Always
    11 to 14 V
    L148-3 (ACC1) - Body ground*1
    L138-11 (ACC1) - Body ground*2
    Power switch on (ACC)
    11 to 14 V
    L149-1 (IG) - Body ground
    Power switch on (IG)
    11 to 14 V

    *1: for 6 Speakers
    *2: for 8 Speakers



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK


3.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)


    C252917E04
  1. Measure the resistance according to the value(s) in the table below.
    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Radio and Display Receiver Assembly)
    *2
    for 6 Speakers
    *3
    for 8 Speakers

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L146-7 (GND1) - Body ground*1
    L138-20 (GND1) - Body ground*2
    Always
    Below 1 Ω

    *1: for 6 Speakers
    *2: for 8 Speakers



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND TERMINAL)
OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)