Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR

FRONT DOOR > DISASSEMBLY

for Preparation Click here



1. REMOVE REAR NO. 2 FLOOR BOARD (for Separate Type)


    B227787E01
  1. Disengage the 2 guides <A> as shown in the illustration.

  1. Disengage the 3 guides <B> and remove the rear No. 2 floor board.



2. REMOVE REAR DECK FLOOR BOX
  1. Remove the rear deck floor box.



3. REMOVE REAR NO. 3 FLOOR BOARD


    B227791
  1. Disengage the 2 guides and remove the rear No. 3 floor board.



4. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG


    B228655
  1. Using a moulding remover, disengage the 3 claws and remove the front door inside handle bezel plug.



5. REMOVE ASSIST GRIP COVER


    B228659
  1. Using a moulding remover, disengage the 6 claws, 2 clips and 3 guides, and remove the assist grip cover.



6. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    B228663
  1. Disengage the 7 claws and 3 guides.

  1. Disconnect the connector and remove the power window regulator master switch assembly with front door armrest base panel.



7. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    B232008
  1. Disengage the 7 claws and 3 guides.

  1. Disconnect each connector and remove the power window regulator switch assembly with front door armrest base panel.



8. REMOVE DOOR ARMREST COVER


    B228665
  1. Remove the door armrest cover.



9. REMOVE COURTESY LIGHT ASSEMBLY


    E189695E01
  1. Using a moulding remover, disengage the claw.

  1. Disconnect the connector and remove the courtesy light assembly.



10. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    B228667E01
  1. Put protective tape around the front door panel.
    Text in Illustration 
    *1
    Protective Tape



    B228669
  1. Remove the 2 screws.

  1. Using a clip remover, disengage the 9 clips.

  1. Pull out the front door trim board sub-assembly in the direction indicated by the arrow in the illustration.

  1. Raise the front door trim board sub-assembly and remove the front door trim board sub-assembly together with the front door inner glass weatherstrip.



    B228673
  1. Disengage the 2 claws and disconnect the front door inside handle sub-assembly.



11. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY


    B228675
  1. Disconnect the front door lock remote control cable and front door inside locking cable, and remove the front door inside handle sub-assembly.



12. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP


    B228679
  1. Disengage the 7 claws and remove the front door inner glass weatherstrip from the front door trim board sub-assembly as shown in the illustration.



13. REMOVE OUTER MIRROR PROTECTOR


    B221534
  1. Remove the screw.

  1. Disengage the 2 claws and remove the outer mirror protector.



14. REMOVE OUTER MIRROR INSTALL HOLE COVER


    B221537
  1. Disengage the 2 claws and guide, remove the outer mirror install hole cover.



15. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY


    B221538
  1. Disconnect the connector.

  1. Remove the 3 bolts.

  1. Disengage the clip and remove the outer rear view mirror assembly.



16. REMOVE DOOR FRAME GARNISH


    B228683
  1. Disengage the clip and remove the door frame garnish.

    HINT:
    This garnish needs to be replaced with a new one because the clip will break when removing the door frame garnish.



17. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY


    E188466
  1. Disconnect the connector.

  1. Using a drill bit with a diameter of less than 4 mm (0.158 in.), drill out the 4 rivet heads and remove the front No. 1 speaker assembly.

    NOTICE:
    1. Do not touch the cone part of the speaker.
    2. Do not drill the rivet at an angle as this will cause damage to the drill and drill hole. Line up the drill and rivet, and carefully drill out the rivet head.
    3. Be careful as the cut rivet will be very hot.

  1. Continue drilling and push out the remaining rivet fragments.

  1. Using a vacuum cleaner, remove the rivet fragments and shavings from the inside of the door.



18. REMOVE FRONT DOOR TRIM BRACKET


    B228685
  1. Remove the 2 screws and front door trim bracket.



19. REMOVE FRONT DOOR SERVICE HOLE COVER


    B228687
  1. Remove the front door service hole cover.

    HINT:
    Remove any remaining butyl tape from the door.



20. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY


    B228691
  1. Remove the grommet.

  1. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

  1. Disconnect the cable from the negative (-) battery terminal and power window regulator master switch assembly.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



    B228693
  1. Remove the 2 bolts.

    NOTICE:
    After the bolts are removed, do not allow the door glass to fall.



    B228697E01
  1. Remove the front door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.

    NOTICE:
    Do not damage the door glass.



21. REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY


    B228699E01
  1. Disconnect the connector.

  1. Loosen the temporary bolt.
    Text in Illustration 
    *1
    Temporary Bolt

    NOTICE:
    Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator may fall and cause damage.

  1. Remove the 5 bolts.

  1. Remove the front door window regulator assembly.

  1. Remove the temporary bolt from the front door window regulator assembly.



22. REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY


    B228701
  1. Using a T25 "TORX" socket wrench, remove the 3 screws and front power window regulator motor assembly.



23. REMOVE FRONT DOOR STIFFENER CUSHION


    B228705E01
  1. Remove the 2 bolts and front door stiffener cushion.
    Text in Illustration 
    *1
    Double-sided Tape



24. REMOVE FRONT DOOR GLASS RUN


    B228703
  1. Remove the front door glass run.



25. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY


    B228710
  1. Remove the bolt and front door rear lower frame sub-assembly as shown in the illustration.



26. REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)


    B228714
  1. Remove the hole plug.



    B228716
  1. Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover with lock cylinder assembly.

    HINT:
    The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.



27. REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)


    B228718
  1. Using a screwdriver, disengage the claw and 2 guides, and remove the front door outside handle cover as shown in the illustration.



28. REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)


    B228715
  1. Remove the hole plug.



    B228723
  1. Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover.

    HINT:
    The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.



29. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY


  1. w/ smart key system



      B228728
    1. Disengage the 2 claws.

    2. Disconnect the connector.



    B228726
  1. Move the lever in the direction indicated by the arrow in the illustration.



    B228730
  1. Remove the front door outside handle assembly as shown in the illustration.



30. REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD


    B228734
  1. Disengage the 3 claws and remove the front door front outside handle pad.



31. REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD


    B228736
  1. Disengage the 2 claws and remove the front door rear outside handle pad.



32. REMOVE FRONT DOOR LOCK ASSEMBLY


    B228738
  1. Disconnect the connector.

  1. Using a T30 "TORX" socket wrench, remove the 3 screws.

  1. Slide the front door lock assembly downward, and remove the front door lock assembly and cables as a unit.



    B228744
  1. Remove the door lock wiring harness seal from the front door lock assembly.



33. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    B228747
  1. Using a screwdriver, disengage the 7 claws as shown in the illustration.

    HINT:
    Tape the screwdriver tip before use.



    B228754
  1. Remove the front door lock remote control cable assembly as shown in the illustration.



34. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY


    B228760
  1. Remove the front door inside locking cable assembly as shown in the illustration.



35. REMOVE ELECTRICAL KEY WIRE HARNESS (w/ Smart Key System)


    B228766
  1. Disconnect the connector.

  1. Disengage the 4 clamps and remove the electrical key wire harness.



36. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY


    B228768
  1. Using a T30 "TORX" socket wrench, loosen the screw.

  1. Slide the front door outside handle frame sub-assembly to disengage the door handle nut and claw of the front door outside handle frame sub-assembly, and then remove it.



37. REMOVE FRONT DOOR LOCK OPEN ROD


    B228772E01
  1. Remove the front door lock open rod as indicated by the arrows, in the order shown in the illustration.



38. REMOVE FRONT DOOR CHECK ASSEMBLY


    B228776
  1. Remove the 3 bolts and front door check assembly.



39. REMOVE FRONT DOOR WEATHERSTRIP


    B228778
  1. Using a clip remover, disengage the 18 clips and remove the front door weatherstrip.



40. REMOVE FRONT DOOR PANEL CUSHION


    B228780
  1. Disengage the 2 claws and remove the 2 front door panel cushions.



41. REMOVE FRONT DOOR BELT MOULDING ASSEMBLY


    B230550E01
  1. Put protective tape around the front door belt moulding assembly.
    Text in Illustration 
    *1
    Protective Tape



    B229330
  1. Using a screwdriver, disengage the 7 claws and remove the front door belt moulding assembly.



42. REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING

HINT:
When removing the front door rear window frame moulding, heat the vehicle body and front door rear window frame moulding using a heat light.

Heating Temperature 
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
Moulding
20 to 30°C (68 to 86°F)

NOTICE:
Do not heat the vehicle body or front door rear window frame moulding moulding excessively.

  1. Using a heat light, heat the front door rear window frame moulding.



    B229337E01
  1. Using a moulding remover, remove the clip and front door rear window frame moulding.
    Text in Illustration 
    *1
    Double-sided Tape



43. REMOVE NO. 1 BLACK OUT TAPE
  1. Using a heat light, heat the No. 1 black out tape and vehicle body.
    Heating Temperature 
    Item
    Temperature
    Vehicle Body
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.



    B229388
  1. Pull back on one of the ends of the No. 1 black out tape to remove it.

    HINT:
    When pulling on the tape, pull it parallel to the body.



44. REMOVE FRONT DOOR OUTSIDE STRIPE
  1. Using a heat light, heat the front door outside stripe and vehicle body.
    Heating Temperature 
    Item
    Temperature
    Vehicle Body
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.



    B229391
  1. Pull back on one of the ends of the front door outside stripe to remove it.

    HINT:
    When pulling on the stripe, pull it parallel to the body.



45. REMOVE FRONT DOOR LOWER OUTSIDE STRIPE
  1. Using a heat light, heat the front door lower outside stripe and vehicle body.
    Heating Temperature 
    Item
    Temperature
    Vehicle Body
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.



    B229393
  1. Pull back on one of the ends of the front door lower outside stripe to remove it.

    HINT:
    When pulling on the stripe, pull it parallel to the body.



46. REMOVE FRONT DOOR REAR OUTSIDE STRIPE
  1. Using a heat light, heat the front door rear outside stripe and vehicle body.
    Heating Temperature 
    Item
    Temperature
    Vehicle Body
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.



    B229395
  1. Pull back on one of the ends of the front door rear outside stripe to remove it.

    HINT:
    When pulling on the stripe, pull it parallel to the body.