Home › General › INTRODUCTION › REPAIR INSTRUCTION

REPAIR INSTRUCTION > INITIALIZATION



PROCEDURES NECESSARY WHEN BATTERY TERMINAL IS DISCONNECTED/RECONNECTED

NOTICE:
  1. After the power switch is turned off, the navigation receiver assembly (for Navigation Receiver Type) or radio and display receiver assembly (w/o Daytime Running Light) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.
  2. When the auxiliary battery is replaced or the cable is disconnected from its negative (-) battery terminal, the ISC learning value will be initialized and symptoms as a loud rattle from the hybrid vehicle transaxle assembly may occur until ISC learning is performed. Therefore, perform ISC learning when the auxiliary battery is replaced or the cable is disconnected from the negative (-) terminal of the auxiliary battery (Click here).


PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED

Replacement Part
Necessary Procedure
Effect / Inoperative Function when Necessary Procedures are not Performed
See Page
  1. Throttle body assembly
  2. Cleaning the deposits from the throttle body assembly
  3. Engine assembly
  4. Cylinder head sub-assembly
  5. Camshaft (for intake or exhaust camshaft)
  6. Camshaft timing gear assembly
  7. Piston or piston ring
  8. Mass air flow meter sub-assembly
  9. Fuel injector assembly
  10. Fuel pump
  11. Air fuel ratio sensor
  12. Heated oxygen sensor
  13. Engine coolant temperature sensor
  14. Spark plug
  15. Ignition coil assembly
  16. EGR valve assembly
  17. Air leaks from intake system
  18. Gas leaks from exhaust system
  19. Knock control sensor
Inspection after repair
  1. Poor idle, etc.
  2. Engine start function, etc
Click here
ECM
Vehicle Identification Number (VIN) registration
MIL comes on
Click here
Millimeter wave radar sensor assembly
Adjust millimeter wave radar sensor assembly (Dynamic radar cruise control system)
  1. Dynamic radar cruise control system
  2. Pre-collision system
Click here
Lane recognition camera sensor assembly
Adjust lane recognition camera sensor assembly (Lane keeping assist system)
  1. Lane keeping assist system
  2. Pre-collision system
Click here
  1. Tire pressure warning ECU
  2. Tire pressure warning valve and transmitter
  1. Code registration (Tire pressure warning system)
  2. Initialization
  1. When DTC detection conditions of "transmitter ID not received" DTC are met, TPWS indicator blinks for 1 minute, and then illuminates.
  2. Tire pressure warning function
Click here for initialization
Click here for registration
Brake booster with master cylinder (Skid control ECU, brake actuator or pressure sensor)
  1. Initialization and calibration of the linear solenoid valve
  2. Yaw rate and acceleration sensor zero point calibration
  1. ABS warning light illumination
  2. Slip indicator light illumination
  3. Brake warning light / yellow (minor malfunction) illumination
  4. VSC disabled or malfunctioning
Click here for initialization
Click here for calibration
  1. Brake pedal stroke sensor
  2. Brake pedal
  1. Clearing stored linear solenoid valve calibration data
  2. Initialization and calibration of the linear solenoid valve
  1. ABS warning light illumination
  2. Slip indicator light illumination
  3. Brake warning light / yellow (minor malfunction) illumination
  4. VSC disabled or malfunctioning
Yaw rate and acceleration sensor
  1. Clearing zero point calibration data
  2. Yaw rate and acceleration sensor zero point calibration
  1. ABS warning light illumination
  2. Slip indicator light illumination
  3. Brake warning light / yellow (minor malfunction) illumination
  4. VSC disabled or malfunctioning
Power steering ECU assembly*1
  1. Torque sensor zero point calibration
  2. Assist map writing
  1. P/S warning light comes on
  2. EPS control
Click here
Electric power steering column sub-assembly (containing the torque sensor)*1
Torque sensor zero point calibration
Steering effort is different between turning steering wheel to left and right
Power steering ECU assembly*2
Rotation angle sensor initialization and torque sensor zero point calibration
  1. P/S warning light comes on
  2. EPS control
Click here
  1. Electric power steering column sub-assembly (containing the torque sensor)*2
  2. Power steering motor assembly*2
Rotation angle sensor initialization and torque sensor zero point calibration
Steering effort is different between turning steering wheel to left and right
Rear height control sensor sub-assembly RH
Perform headlight leveling ECU initialization
Automatic leveling function
Click here
Inner rear view mirror assembly*3
Re-registration of codes in the garage door opener system
  1. Register transmitter code
  2. Rolling code systems
Garage door opener system
Click here
DCM (Telematics Transceiver)
DCM activation
Safety connect system
Click here
  1. Certification ECU (smart key ECU assembly)
  2. ID code box (immobiliser code ECU)*4
  3. Transmission control ECU assembly
  4. Key
Code registration (Engine immobiliser system)
  1. Wireless door lock control system
  2. Smart key system
  3. Hybrid start
Click here
  1. Occupant classification ECU
  2. Front passenger seat
  1. Zero point calibration (Occupant classification system)
  2. Sensitivity check (Occupant classification system)
  1. Occupant classification system
  2. Passenger airbag ON/OFF indicator
  3. Airbag system (Front passenger side)
  4. Seat belt warning system (Front passenger side)
Click here
  1. Power window regulator motor
  2. Door window regulator
Initialize power window control system
  1. Automatic door glass open/ close function
  2. Jam protection function
  3. Operation function after power switch is turned off
Click here
  1. Sliding roof ECU (sliding roof drive gear sub-assembly)
  2. Sliding roof glass
  3. Sliding roof housing
Initialize sliding roof ECU (pulse sensor initial position setting)
  1. Automatic open function of sliding roof
  2. Jam protection function
  3. Operation function after power switch is turned off
Click here
  1. Headlight leveling ECU
  2. Suspension, tires, etc.
Perform headlight leveling ECU initialization
Automatic leveling function
Click here
  1. *1: for Brush Type Motor
  2. *2: for Brushless Type Motor
  3. *3: w/ Garage Door Opener System
  4. *4: for Canada