AUDIO AND VISUAL SYSTEM (w/ Daytime Running Light) > Speaker Circuit |

| 1.CHECK HARNESS AND CONNECTOR |
Disconnect the connectors from the radio and display receiver assembly and speakers.
Measure the resistance between each of the front No. 2 speaker assemblies and the radio and display receiver assembly to check for an open circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
| L146-1 (FR+) - I2-2 (+) | Always | Below 1 Ω |
| L146-5 (FR-) - I2-4 (-) | Always | Below 1 Ω |
| L146-2 (FL+) - I3-2 (+) | Always | Below 1 Ω |
| L146-6 (FL-) - I3-4 (-) | Always | Below 1 Ω |
Measure the resistance between each of the front No. 1 speaker assemblies and the front No. 2 speaker assemblies to check for an open circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
| I2-1 (+) - N1-1 | Always | Below 1 Ω |
| I2-3 (-) - N1-2 | Always | Below 1 Ω |
| I3-1 (+) - O1-1 | Always | Below 1 Ω |
| I3-3 (-) - O1-2 | Always | Below 1 Ω |
Measure the resistance between each of the rear speaker assemblies and the radio and display receiver assembly to check for an open circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
| L147-1 (RR+) - P3-1 | Always | Below 1 Ω |
| L147-3 (RR-) - P3-2 | Always | Below 1 Ω |
| L147-2 (RL+) - Q3-1 | Always | Below 1 Ω |
| L147-6 (RL-) - Q3-2 | Always | Below 1 Ω |
Measure the resistance between the radio and display receiver assembly and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
| L146-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| L146-5 (FR-) - Body ground | Always | 10 kΩ or higher |
| L146-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| L146-6 (FL-) - Body ground | Always | 10 kΩ or higher |
| L147-1 (RR+) - Body ground | Always | 10 kΩ or higher |
| L147-3 (RR-) - Body ground | Always | 10 kΩ or higher |
| L147-2 (RL+) - Body ground | Always | 10 kΩ or higher |
| L147-6 (RL-) - Body ground | Always | 10 kΩ or higher |
Measure the resistance between each of the front No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
| I2-1 (+) - Body ground | Always | 10 kΩ or higher |
| I2-3 (-) - Body ground | Always | 10 kΩ or higher |
| I3-1 (+) - Body ground | Always | 10 kΩ or higher |
| I3-3 (-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 2.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY |
Resistance check
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| N1-1 - N1-2 | Always | 3.2 to 4.8 Ω |
| O1-1 - O1-2 | Always | 3.2 to 4.8 Ω |
| *A | for RH |
| *B | for LH |
| *a | Component without harness connected (Front No. 1 Speaker Assembly) |
|
| ||||
| OK | |
| 3.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY |
Resistance check
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I2-2 (+) - I2-4 (-) | Always | 10 kΩ or higher |
| I2-1 (+) - I2-2 (+) | Always | Below 1 Ω |
| I2-3 (-) - I2-4 (-) | Always | Below 1 Ω |
| I3-2 (+) - I3-4 (-) | Always | 10 kΩ or higher |
| I3-1 (+) - I3-2 (+) | Always | Below 1 Ω |
| I3-3 (-) - I3-4 (-) | Always | Below 1 Ω |
| *A | for RH |
| *B | for LH |
| *a | Component without harness connected (Front No. 2 Speaker Assembly) |
|
| ||||
| OK | |
| 4.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY |
Check that the malfunction disappears when a known good speaker is installed (Click here).
|
| ||||
| OK | ||
| ||
| 5.INSPECT REAR SPEAKER ASSEMBLY |
Resistance check
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| P3-1 - P3-2 | Always | 3.2 to 4.8 Ω |
| Q3-1 - Q3-2 | Always | 3.2 to 4.8 Ω |
| *A | for RH |
| *B | for LH |
| *a | Component without harness connected (Rear Speaker Assembly) |
|
| ||||
| OK | ||
| ||