Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type)

NAVIGATION SYSTEM (for Radio and Display Type) > Speaker Circuit

for Preparation Click here


DESCRIPTION

for 6 Speakers:
  1. If there is a short in a speaker circuit, the radio and display receiver assembly detects it and stops output to the speakers.
  2. Thus sound cannot be heard from the speakers even if there is no malfunction in the radio and display receiver assembly or speakers.
  3. If a short is detected in a speaker circuit, no sound can be heard from the speakers.
for 8 Speakers:
  1. If there is a short in a speaker circuit, the stereo component amplifier assembly detects it and stops output to the speakers.
  2. Thus sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly or speakers.
  3. If a short is detected in a speaker circuit, no sound can be heard from the speakers.

WIRING DIAGRAM


for 6 Speakers

E230315E04


for 8 Speakers

E241547E01


E241548E01


INSPECTION PROCEDURE

1.CONFIRM MODEL

Result:
Result
Proceed to
for 6 Speakers
A
for 8 Speakers
B



B
Go to step 7
A


2.CHECK HARNESS AND CONNECTOR
  1. Disconnect the connectors from the radio and display receiver assembly and speakers.

  1. Measure the resistance between each of the front No. 2 speaker assemblies and the radio and display receiver assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L146-1 (FR+) - I2-2 (+)
    Always
    Below 1 Ω
    L146-5 (FR-) - I2-4 (-)
    Always
    Below 1 Ω
    L146-2 (FL+) - I3-2 (+)
    Always
    Below 1 Ω
    L146-6 (FL-) - I3-4 (-)
    Always
    Below 1 Ω

  1. Measure the resistance between each of the front No. 1 speaker assemblies and the front No. 2 speaker assemblies to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I2-1 (+) - N1-1
    Always
    Below 1 Ω
    I2-3 (-) - N1-2
    Always
    Below 1 Ω
    I3-1 (+) - O1-1
    Always
    Below 1 Ω
    I3-3 (-) - O1-2
    Always
    Below 1 Ω

  1. Measure the resistance between each of the rear speaker assemblies and the radio and display receiver assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L147-1 (RR+) - P3-1
    Always
    Below 1 Ω
    L147-3 (RR-) - P3-2
    Always
    Below 1 Ω
    L147-2 (RL+) - Q3-1
    Always
    Below 1 Ω
    L147-6 (RL-) - Q3-2
    Always
    Below 1 Ω

  1. Measure the resistance between the radio and display receiver assembly and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L146-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    L146-5 (FR-) - Body ground
    Always
    10 kΩ or higher
    L146-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    L146-6 (FL-) - Body ground
    Always
    10 kΩ or higher
    I147-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    I147-3 (RR-) - Body ground
    Always
    10 kΩ or higher
    I147-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    I147-6 (RL-) - Body ground
    Always
    10 kΩ or higher

  1. Measure the resistance between each of the front No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I2-1 (+) - Body ground
    Always
    10 kΩ or higher
    I2-3 (-) - Body ground
    Always
    10 kΩ or higher
    I3-1 (+) - Body ground
    Always
    10 kΩ or higher
    I3-3 (-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


  1. Resistance check



      E219303E61
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      N1-1 - N1-2
      Always
      3.2 to 4.8 Ω
      O1-1 - O1-2
      Always
      3.2 to 4.8 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Front No. 1 Speaker Assembly)



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


4.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


  1. Resistance check



      E226097E21
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I2-2 (+) - I2-4 (-)
      Always
      10 kΩ or higher
      I2-1 (+) - I2-2 (+)
      Always
      Below 1 Ω
      I2-3 (-) - I2-4 (-)
      Always
      Below 1 Ω
      I3-2 (+) - I3-4 (-)
      Always
      10 kΩ or higher
      I3-1 (+) - I3-2 (+)
      Always
      Below 1 Ω
      I3-3 (-) - I3-4 (-)
      Always
      Below 1 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Front No. 2 Speaker Assembly)



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK


5.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY
  1. Check that the malfunction disappears when a known good speaker is installed (Click here).

    OK:
    Malfunction disappears.

    HINT:
    1. Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
    2. When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
    3. Perform the above inspection on both LH and RH sides.



NG
Go to step 6
OK

END (FRONT NO. 2 SPEAKER ASSEMBLY WAS DEFECTIVE) 

6.INSPECT REAR SPEAKER ASSEMBLY


  1. Resistance check



      E219303E57
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      P3-1 - P3-2
      Always
      3.2 to 4.8 Ω
      Q3-1 - Q3-2
      Always
      3.2 to 4.8 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Rear Speaker Assembly)



NG
REPLACE REAR SPEAKER ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

7.CHECK HARNESS AND CONNECTOR
  1. Disconnect the connectors from the stereo component amplifier assembly and speakers.

  1. Measure the resistance between the front No. 1 speaker assembly RH and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L142-15 (WFR+) - N1-1
    Always
    Below 1 Ω
    L142-30 (WFR-) - N1-2
    Always
    Below 1 Ω

  1. Measure the resistance between the front No. 1 speaker assembly LH and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L142-8 (WFL+) - O1-1
    Always
    Below 1 Ω
    L142-23 (WFL-) - O1-2
    Always
    Below 1 Ω

  1. Measure the resistance between each of the front No. 2 speaker assemblies and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L142-9 (FR+) - I4-1
    Always
    Below 1 Ω
    L142-24 (FR-) - I4-2
    Always
    Below 1 Ω
    L142-14 (FL+) - I5-1
    Always
    Below 1 Ω
    L142-29 (FL-) - I5-2
    Always
    Below 1 Ω

  1. Measure the resistance between each of the rear speaker assemblies and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L142-12 (RR+) - P3-1
    Always
    Below 1 Ω
    L142-27 (RR-) - P3-2
    Always
    Below 1 Ω
    L142-11 (RL+) - Q3-1
    Always
    Below 1 Ω
    L142-26 (RL-) - Q3-2
    Always
    Below 1 Ω

  1. Measure the resistance between the rear No. 2 speaker assemblies and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L142-13 (TWR+) - P5-1
    Always
    Below 1 Ω
    L142-28 (TWR-) - P5-2
    Always
    Below 1 Ω
    L142-10 (TWL+) - Q5-1
    Always
    Below 1 Ω
    L142-25 (TWL-) - Q5-2
    Always
    Below 1 Ω

  1. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L142-15 (WFR+) - Body ground
    Always
    10 kΩ or higher
    L142-30 (WFR-) - Body ground
    Always
    10 kΩ or higher
    L142-8 (WFL+) - Body ground
    Always
    10 kΩ or higher
    L142-23 (WFL-) - Body ground
    Always
    10 kΩ or higher
    L142-9 (FR+) - Body ground
    Always
    10 kΩ or higher
    L142-24 (FR-) - Body ground
    Always
    10 kΩ or higher
    L142-14 (FL+) - Body ground
    Always
    10 kΩ or higher
    L142-29 (FL-) - Body ground
    Always
    10 kΩ or higher
    L142-12 (RR+) - Body ground
    Always
    10 kΩ or higher
    L142-27 (RR-) - Body ground
    Always
    10 kΩ or higher
    L142-11 (RL+) - Body ground
    Always
    10 kΩ or higher
    L142-26 (RL-) - Body ground
    Always
    10 kΩ or higher
    L142-13 (TWR+) - Body ground
    Always
    10 kΩ or higher
    L142-28 (TWR-) - Body ground
    Always
    10 kΩ or higher
    L142-10 (TWL+) - Body ground
    Always
    10 kΩ or higher
    L142-25 (TWL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    E219303E61
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      N1-1 - N1-2
      Always
      4.6 to 6.6 Ω
      O1-1 - O1-2
      Always
      4.6 to 6.6 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Front No. 1 Speaker Assembly)



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


9.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    E187205E05
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I4-1 - I4-2
      Always
      3.2 to 4.8 Ω
      I5-1 - I5-2
      Always
      3.2 to 4.8 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Front No. 2 Speaker Assembly)



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK


10.INSPECT REAR SPEAKER ASSEMBLY


    E219303E60
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      P3-1 - P3-2
      Always
      3.2 to 5.2 Ω
      Q3-1 - Q3-2
      Always
      3.2 to 5.2 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Rear Speaker Assembly)



NG
REPLACE REAR SPEAKER ASSEMBLY (Click here)
OK


11.INSPECT REAR NO. 2 SPEAKER ASSEMBLY


    E187136E07
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      P5-1 - P5-2
      Always
      3.2 to 4.8 Ω
      Q5-1 - Q5-2
      Always
      3.2 to 4.8 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Rear No. 2 Speaker Assembly)



NG
REPLACE REAR NO. 2 SPEAKER ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)