Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM

SEAT BELT WARNING SYSTEM > Front Passenger Side Seat Belt Warning Light Malfunction

for Preparation Click here


DESCRIPTION

The occupant classification ECU detects the state of the front seat inner belt assembly RH and occupant classification sensor when the front passenger side seat is occupied with the power switch on (IG). If the front passenger side seat belt is not fastened, the front passenger side seat belt warning light blinks. If the seat belt is fastened, the warning light goes off.

WIRING DIAGRAM


B230279E01


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. The seat belt warning system uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure (Click here).

1.CHECK DTC OUTPUT (OCCUPANT CLASSIFICATION SYSTEM)
  1. Clear the DTC (Click here).

  1. Recheck for DTCs.

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
GO TO OCCUPANT CLASSIFICATION SYSTEM (Click here)
A


2.CHECK DTC OUTPUT (AIRBAG SYSTEM)
  1. Clear the DTC (Click here).

  1. Recheck for DTCs.

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
GO TO AIRBAG SYSTEM (Click here)
A


3.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Combination Meter / Active Test.

  1. Perform the Active Test according to the display on the Techstream.

    Combination Meter (Combination Meter Assembly) 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Front Passenger Side Seat Belt
    Front passenger side seat belt warning light
    OFF or ON
    Confirm that the vehicle stopped with the engine idling

    OK:
    The front passenger side seat belt warning light operates normally.



NG
Go to step 4
OK

REPLACE NO. 3 METER CIRCUIT PLATE (Click here)  

4.CHECK HARNESS AND CONNECTOR (PASSENGER SEAT BELT WARNING LIGHT - BATTERY)


    B230277E01
  1. Disconnect the M2 connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    M2-6 (IG+) - Body ground
    Power switch on (IG)
    11 to 14 V
    M2-6 (IG+) - Body ground
    Power switch off
    Below 1 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Passenger Seat Belt Warning Light Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (COMBINATION METER - PASSENGER SEAT BELT WARNING LIGHT)


    B230292E01
  1. Disconnect the L27 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L27-21 (PBLT) - M2-3 (PBEW)
    Always
    Below 1 Ω
    L27-21 (PBLT)- Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Combination Meter Assembly)
    *2
    Front view of wire harness connector
    (to Passenger Seat Belt Warning Light Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BATTERY)
  1. Reconnect the M2 connector.



    B203742E03
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L27-21 (PBLT) - Body ground
    Power switch on (IG)
    11 to 14 V
    L27-21 (PBLT) - Body ground
    Power switch off
    Below 1 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Combination Meter Assembly)



NG
REPLACE PASSENGER SEAT BELT WARNING LIGHT ASSEMBLY (Click here)
OK

REPLACE NO. 3 METER CIRCUIT PLATE (Click here)