Home › Vehicle Interior › SEAT BELT › FRONT PASSENGER SEAT BELT WARNING LIGHT

FRONT PASSENGER SEAT BELT WARNING LIGHT > REMOVAL

for Preparation Click here



1. REMOVE REAR NO. 2 FLOOR BOARD (for Separate Type)


    B227787E01
  1. Disengage the 2 guides <A> as shown in the illustration.

  1. Disengage the 3 guides <B> and remove the rear No. 2 floor board.



2. REMOVE REAR DECK FLOOR BOX
  1. Remove the rear deck floor box.



3. REMOVE REAR NO. 3 FLOOR BOARD


    B227791
  1. Disengage the 2 guides and remove the rear No. 3 floor board.



4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



5. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY


    B223452E01
  1. Using a moulding remover, slightly lift the panel at the position shown in the illustration.
    Text in Illustration 
    *a
    Lift slightly

  1. Pull the integration control and panel assembly in the direction indicated by the arrow to disengage the 6 claws.

  1. Disconnect each connector and remove the integration control and panel assembly.



6. REMOVE LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    B223454
  1. Pull the lower center instrument cluster finish panel sub-assembly in the direction indicated by the arrow to disengage the 2 claws and 2 clips.



    B223455
  1. Pull the lower center instrument cluster finish panel sub-assembly in the direction indicated by the arrow to disengage the 5 claws and remove the lower center instrument cluster finish panel sub-assembly.



7. REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH
  1. Disengage the 14 claws.



  1. Disconnect the connector and remove the instrument cluster finish panel garnish.


    B223458



8. REMOVE UPPER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    B223459
  1. Disengage the 3 claws.

  1. Disconnect the connector and remove the upper instrument panel finish panel sub-assembly.



9. REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (for Radio and Display Type)
w/ Daytime Running Light:
w/o Daytime Running Light:


10. REMOVE NAVIGATION RECEIVER WITH BRACKET (for Navigation Receiver Type)


    E188505
  1. Remove the 4 bolts.



    E188507
  1. Disengage the 4 claws and remove the navigation receiver with bracket as shown in the illustration.

  1. Disconnect each connector.



11. REMOVE NO. 1 SIDE DEFROSTER NOZZLE


    B223480E01
  1. Using a moulding remover, slightly lift the panel at the position shown in the illustration.
    Text in Illustration 
    *a
    Lift slightly

  1. Pull the No. 1 side defroster nozzle in the direction indicated by the arrow to disengage the 3 claws and remove the No. 1 side defroster nozzle.



12. REMOVE NO. 2 INSTRUMENT PANEL REGISTER


    B223482
  1. Pull the No. 2 instrument panel register in the direction indicated by the arrow to disengage the claw and clip.



    B223483
  1. Pull the No. 2 instrument panel register in the direction indicated by the arrow to disengage the 2 claws and remove the No. 2 instrument panel register.



13. REMOVE GLOVE COMPARTMENT DOOR
  1. Open the glove compartment door assembly.



    B223485
  1. Pull the glove compartment door in the direction indicated by the arrow to disengage the 7 claws.

  1. Pull the glove compartment door in the direction indicated by the arrow to remove the glove compartment door.



14. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL GARNISH
  1. Remove the 2 screws <C>.

  1. Disengage the 7 claws.



  1. Disconnect the connector and remove the center instrument cluster finish panel garnish.


    B223497



15. REMOVE PASSENGER SEAT BELT WARNING LIGHT ASSEMBLY


    B226678
  1. Disengage the 2 claws and remove the passenger seat belt warning light assembly as shown in the illustration.