Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM (for Brush Type Motor)

DTC    C1511    Torque Sensor Circuit Malfunction

DTC    C1512    Torque Sensor Circuit Malfunction

DTC    C1513    Torque Sensor Circuit Malfunction

DTC    C1514    Torque Sensor Power Supply Abnormal

DTC    C1517    Torque Hold Abnormal

for Preparation Click here


DESCRIPTION

The power steering ECU calculates assisting power based on steering torque signals from the torque sensor. If these DTCs are stored in the power steering ECU assembly, the ECU stops steering power assist as a fail-safe function.

DTC No.
DTC Detection Condition
Trouble Area
C1511
Torque sensor (TRQ1) signal error or stop
  1. Torque sensor (built into electric power steering column sub-assembly)
  1. Power steering ECU assembly
C1512
Torque sensor (TRQ2) signal error or stop
C1513
Deviation between torque sensor TRQ1 and TRQ2 exceeds specified value
C1514
Torque sensor power source voltage error
C1517
Temporary control due to malfunction related to torque sensor continues for long time

WIRING DIAGRAM


C245322E07


INSPECTION PROCEDURE

NOTICE:
  1. If the power steering ECU assembly has been replaced with a new one, perform assist map writing and torque sensor zero point calibration (Click here).
  2. If the electric power steering column sub-assembly has been replaced with a new one, perform torque sensor zero point calibration after performing the initialization of the torque sensor zero point value (Click here).

1.CHECK CONNECTOR CONNECTION CONDITION (TORQUE SENSOR - ECU)
  1. Check the installation condition of the torque sensor connector.

    OK:
    Torque sensor connector is securely connected to the power steering ECU assembly.



NG
CONNECT CONNECTOR
OK


2.CHECK POWER STEERING ECU ASSEMBLY (TOQUE SENSOR OUTPUT)


    C164819E26
  1. Turn the power switch on (READY).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    z13-6 (TRQV) - z13-8 (TRQG)
    Power switch on (READY)
    4.5 to 5.5 V

    Text in Illustration 
    *1
    Component with harness connected
    (Power Steering ECU Assembly)



NG
REPLACE POWER STEERING ECU ASSEMBLY (Click here)
OK


3.CHECK ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY (TORQUE SENSOR)


    C164819E27
  1. Turn the power switch on (READY).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition (Steering Wheel Position)
    Specified Condition
    z13-5 (TRQ1) - z13-8 (TRQG)
    Power switch on (READY)
    Center position
    2.3 to 2.7 V
    z13-7 (TRQ2) - z13-8 (TRQG)
    Power switch on (READY)
    Center position
    2.3 to 2.7 V
    z13-5 (TRQ1) - z13-8 (TRQG)
    Power switch on (READY)
    Turned to right
    2.5 to 3.8 V
    z13-7 (TRQ2) - z13-8 (TRQG)
    Power switch on (READY)
    Turned to right
    1.2 to 2.5 V
    z13-5 (TRQ1) - z13-8 (TRQG)
    Power switch on (READY)
    Turned to left
    1.2 to 2.5 V
    z13-7 (TRQ2) - z13-8 (TRQG)
    Power switch on (READY)
    Turned to left
    2.5 to 3.8 V

  1. Under each condition, measure the voltage at terminals TRQ1 and TRQ2, and calculate the sum.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Sum of voltage between z13-5 (TRQ1) and z13-8 (TRQG) and voltage between z13-7 (TRQ2) and z13-8 (TRQG)
    Power switch on (READY)
    Steering wheel not being turned (without load)
    Between 4.75 V and 5.25 V
    Power switch on (READY)
    Steering wheel being turned to the right with vehicle stopped
    Power switch on (READY)
    Steering wheel being turned to the left with vehicle stopped

    Text in Illustration 
    *1
    Component with harness connected
    (Power Steering ECU Assembly)



NG
REPLACE ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY (Click here)
OK

REPLACE POWER STEERING ECU ASSEMBLY (Click here)