Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK

FRONT DOOR LOCK > INSTALLATION

for Preparation Click here



1. INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY


    B228761
  1. Install the front door inside locking cable assembly as shown in the illustration.



2. INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    B228756
  1. Install the front door lock remote control cable assembly as shown in the illustration.



    B228749
  1. Engage the 7 claws as shown in the illustration.



3. INSTALL FRONT DOOR LOCK ASSEMBLY

NOTICE:
  1. When reusing the removed front door lock assembly, replace the door lock wiring harness seal on the connector with a new one.
  2. Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.
  3. Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water intrusion. This may result in a malfunction of the front door lock assembly.

  1. Apply MP grease to the sliding parts of the front door lock assembly.



    B228744
  1. Install a new door lock wiring harness seal to the front door lock assembly.



    B228739
  1. Insert the front door lock open rod to the front door lock assembly.

  1. Make sure that the front door lock open rod is securely connected to the front door lock assembly.

  1. Using a T30 "TORX" socket wrench, install the front door lock assembly with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



4. INSTALL FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)


    B228724
  1. Install the front door outside handle cover with lock cylinder assembly.

    HINT:
    Make sure that the front door lock cylinder rod is inserted into the front door lock assembly.



    B228716
  1. Using a T30 "TORX" socket wrench, install the front door lock cylinder with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



    B228714
  1. Install the hole plug.



5. INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY


    B228712
  1. Install the front door rear lower frame sub-assembly with the bolt as shown in the illustration.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



6. INSTALL FRONT DOOR GLASS RUN


    B228703
  1. Install the front door glass run.



7. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY
  1. Connect the cable to the negative (-) battery terminal.

  1. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

  1. Disconnect the cable from the negative (-) battery terminal and power window regulator master switch assembly.



    B228695E01
  1. Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated by the arrows, in the order shown in the illustration.



    B228693
  1. Install the front door glass sub-assembly with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    B228691
  1. Install the grommet.

  1. Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



8. INSTALL FRONT DOOR SERVICE HOLE COVER
  1. Apply butyl tape to the front door panel.



    B228689E01
  1. Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.

  1. Attach the front door service hole cover according to the reference points on the front door panel.
    Text in Illustration 
    *1
    Reference Point

    NOTICE:
    Securely install the front door service hole cover preventing wrinkles and air bubbles.



9. INSTALL FRONT DOOR TRIM BRACKET


    B228685
  1. Install the front door trim bracket with the 2 screws.



10. INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY


    B228676
  1. Connect the front door lock remote control cable assembly and front door inside locking cable assembly to the front door inside handle.



    B228673
  1. Engage the 2 claws and install the front door inside handle sub-assembly to the front door trim board sub-assembly.



11. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    B228671
  1. Engage the 9 clips and install the front door trim board sub-assembly.

  1. Install the 2 screws.

  1. Remove the 2 pieces of protective tape.



12. INSTALL COURTESY LIGHT ASSEMBLY
  1. Connect the connector.



    E189696E01
  1. Engage the claw to install the courtesy light assembly.



13. INSTALL DOOR ARMREST COVER


    B228665
  1. Install the door armrest cover.



14. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    B228663
  1. Connect the connector.

  1. Engage the 7 claws and 3 guides, and install the power window regulator master switch assembly with front door armrest base panel.



15. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)
  1. Connect each connector.



    B232008
  1. Engage the 7 claws and 3 guides, and install the power window regulator switch assembly with front door armrest base panel.



16. INSTALL ASSIST GRIP COVER


    B228660
  1. Engage the 6 claws, 2 clips and 3 guides, and install the assist grip cover.



17. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG


    B228657
  1. Engage the 3 claws and install the front door inside handle bezel plug.



18. INSTALL REAR NO. 3 FLOOR BOARD


    B227791
  1. Engage the 2 guides to install the rear No. 3 floor board.



19. INSTALL REAR DECK FLOOR BOX
  1. Install the rear deck floor box.



20. INSTALL REAR NO. 2 FLOOR BOARD (for Separate Type)


    B227788E01
  1. Engage the 3 guides <A>.

  1. Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.



21. INITIALIZE POWER WINDOW CONTROL SYSTEM
(Click here)


22. CHECK POWER WINDOW CONTROL SYSTEM
(Click here)