REAR DOOR LOCK > REMOVAL |
| 1. REMOVE REAR NO. 2 FLOOR BOARD (for Separate Type) |
![]() |
Disengage the 2 guides <A> as shown in the illustration.
Disengage the 3 guides <B> and remove the rear No. 2 floor board.
| 2. REMOVE REAR DECK FLOOR BOX |
Remove the rear deck floor box.
| 3. REMOVE REAR NO. 3 FLOOR BOARD |
![]() |
Disengage the 2 guides and remove the rear No. 3 floor board.
| 4. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG |
![]() |
Using a moulding remover, disengage the 3 claws and remove the rear door inside handle bezel plug.
| 5. REMOVE DOOR ASSIST GRIP COVER |
![]() |
Using a moulding remover, disengage the 6 claws, 2 clips and 3 guides, and remove the door assist grip cover.
| 6. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL |
![]() |
Disengage the 7 claws and 2 guides.
Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.
| 7. REMOVE REAR DOOR ARMREST COVER |
![]() |
Remove the rear door armrest cover.
| 8. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY |
![]() |
Put protective tape around the rear door panel.
| *1 | Protective Tape |
![]() |
Remove the 2 screws.
Using a clip remover, disengage the 8 clips.
Pull out the rear door trim board sub-assembly in the direction indicated by the arrow in the illustration.
Raise the rear door trim board sub-assembly and remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.
![]() |
Disengage the 2 claws and disconnect the rear door inside handle sub-assembly.
for 8 Speakers:
Disconnect the connector.
| 9. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY |
![]() |
Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly, and remove the rear door inside handle sub-assembly.
| 10. REMOVE REAR DOOR TRIM BRACKET |
![]() |
Remove the 2 screws and rear door trim bracket.
| 11. REMOVE REAR DOOR SERVICE HOLE COVER |
![]() |
Disconnect the 2 connectors.
Disengage the clamp and remove the rear door service hole cover.
| 12. REMOVE REAR DOOR GLASS RUN |
![]() |
Remove the rear door glass run.
| 13. REMOVE REAR DOOR WINDOW GUIDE SUB-ASSEMBLY |
![]() |
Remove the screw.
Remove the bolt and rear door window guide sub-assembly.
| 14. REMOVE REAR DOOR REAR GUIDE SEAL |
![]() |
Loosen the temporary screw.
| *1 | Temporary Screw |
Remove the 2 screws and rear door rear guide seal.
Remove the temporary screw from the rear door window division bar sub-assembly.
| 15. REMOVE REAR DOOR GLASS SUB-ASSEMBLY |
Connect the rear power window regulator motor connector.
Connect the power window regulator switch assembly and move the rear door glass sub-assembly so that the door glass bolts can be seen.
Disconnect the power window regulator switch assembly and rear power window regulator motor connector.
Disconnect the cable from the negative (-) battery terminal.
![]() |
Remove the 2 bolts and rear door glass sub-assembly as shown in the illustration.
| 16. REMOVE REAR DOOR LOCK ASSEMBLY |
![]() |
Using a T30 "TORX" socket wrench, remove the 3 screws.
Move the rear door lock assembly downward and pull the release plate out of the rear door outside handle frame.
![]() |
Remove the door lock wiring harness seal from the rear door lock assembly.
| 17. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY |
![]() |
Using a screwdriver, disengage the 2 claws as shown in the illustration.
![]() |
Remove the rear door lock remote control cable assembly as shown in the illustration.
| 18. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY |
![]() |
Using a screwdriver, disengage the 4 claws as shown in the illustration.
![]() |
Remove the rear door inside locking cable assembly as shown in the illustration.