Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM

POWER MIRROR CONTROL SYSTEM > Mirror Heater does not Operate with Rear Defogger Switch

for Preparation Click here


DESCRIPTION

When the rear window defogger switch on the air conditioning control panel assembly is pressed, the operation signal is transmitted to the air conditioning amplifier assembly through a LIN communication line. When the air conditioning amplifier assembly receives the signal, it turns on the integration relay to operate the mirror heater.

WIRING DIAGRAM


B267922E03


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical /Air Conditioner / Active Test.

  1. Perform an Active Test according to the display on the Techstream.

    Air Conditioner 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Mirror Heater Relay
    Mirror heater
    ON / OFF
    -

    Result:
    Result
    Proceed to
    Mirror heater operation on both mirrors is not normal
    A
    Mirror heater operation on RH side mirror is not normal
    B
    Mirror heater operation on LH side mirror is not normal
    C



B
Go to step 8

C
Go to step 9
A


2.CHECK DEFOGGER SYSTEM
  1. Check the rear window defogger operation.

    OK:
    The rear window defogger operated normally.



NG
GO TO WINDOW DEFOGGER SYSTEM (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - BODY GROUND)


    B232319E01
  1. Disconnect the integration relay connector.

  1. Measure the resistance according to the value(s) in the table below

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1H-3 (GND2) - Body ground
    Always
    Below 1 Ω
    1G-22 (GND1) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Integration Relay)
    *2
    Front view of wire harness connector
    (to Integration Relay)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - INTEGRATION RELAY)


    B232341E02
  1. Disconnect the integration relay connector.

  1. Disconnect the outer rear view mirror assembly RH connector.

  1. Measure the resistance according to the value(s) in the table below

    Tester Connection
    Condition
    Specified Condition
    1I-2 (MHTR) - N3-1 (HR+)
    Always
    Below 1 Ω
    1I-2 (MHTR) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Outer Rear View Mirror Assembly RH)
    *2
    Front view of wire harness connector
    (to Integration Relay)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH - INTEGRATION RELAY)


    B232341E05
  1. Disconnect the integration relay connector.

  1. Disconnect the outer rear view mirror assembly LH connector.

  1. Measure the resistance according to the value(s) in the table below

    Tester Connection
    Condition
    Specified Condition
    1I-2 (MHTR) - O3-1 (HL+)
    Always
    Below 1 Ω
    1I-2 (MHTR) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Outer Rear View Mirror Assembly LH)
    *2
    Front view of wire harness connector
    (to Integration Relay)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.REPLACE INTEGRATION NO.1 RELAY
  1. Replace the integration relay (Click here).


OK


7.CHECK REAR WINDOW DEFOGGER AND MIRROR HEATER
  1. Check the mirror heater system.

    OK:
    Mirror heater system is normal.



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK

END (INTEGRATION RELAY WAS DEFECTIVE) 

8.CHECK OUTER REAR VIEW MIRROR ASSEMBLY RH


    B231927E06
  1. Remove the outer rear view mirror assembly RH (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N3-1 (HR+) - N3-2 (HR-)
    25°C (77°F)
    7.6 to 11.4 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Outer Rear View Mirror Assembly RH)



NG
REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH (FRONT PASSENGER SIDE) (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY - OUTER REAR VIEW MIRROR ASSEMBLY RH) 

9.CHECK OUTER REAR VIEW MIRROR ASSEMBLY LH


    B231927E01
  1. Remove the outer rear view mirror assembly LH (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O3-1 (HL+) - O3-2 (HL-)
    25°C (77°F)
    7.6 to 11.4 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Outer Rear View Mirror Assembly LH)



NG
REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH (DRIVER SIDE) (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY - OUTER REAR VIEW MIRROR ASSEMBLY LH)