Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM (for Brushless Type Motor)

DTC    C1511    Torque Sensor Circuit Malfunction

DTC    C1512    Torque Sensor Circuit Malfunction

DTC    C1513    Torque Sensor Circuit Malfunction

DTC    C1514    Torque Sensor Power Supply Abnormal

DTC    C1517    Torque Hold Abnormal

for Preparation Click here


DESCRIPTION

The torque sensor converts the steering wheel rotation torque into electric signals and sends them to the power steering ECU assembly.

DTC No.
DTC Detection Condition
Trouble Area
C1511
Torque sensor malfunction
  1. Torque sensor (built into electric power steering column sub-assembly)
  2. Power steering ECU assembly
C1512
C1513
C1514
C1517

WIRING DIAGRAM


C245322E06


INSPECTION PROCEDURE

NOTICE:
  1. If the power steering ECU assembly has been replaced with a new one, perform rotation angle sensor initialization and torque sensor zero point calibration (Click here).
  2. If the electric power steering column sub-assembly or power steering motor assembly has been replaced, perform rotation angle sensor initialization and torque sensor zero point calibration (Click here).

1.CHECK CONNECTOR CONNECTION CONDITION (TORQUE SENSOR - ECU)
  1. Check the connection condition of the torque sensor connector.

    OK:
    Torque sensor connector is securely connected to the power steering ECU assembly.



NG
CONNECT CONNECTOR
OK


2.CHECK POWER STEERING ECU ASSEMBLY (TRQV, TRQF VOLTAGE)
C113531E20
  1. Turn the power switch on (READY).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    z14-6 (TRQV) - z14-8 (TRQG)
    Power switch on (READY)
    4.5 to 5.5 V

    Text in Illustration 
    *1
    Component with harness connected
    (Power Steering ECU Assembly)



NG
REPLACE POWER STEERING ECU ASSEMBLY (Click here)
OK


3.CHECK POWER STEERING ECU ASSEMBLY (TRQ1, TRQ2 VOLTAGE)


    C113531E21
  1. Turn the power switch on (READY).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition (Steering Wheel Position)
    Specified Condition
    z14-5 (TRQ1) - z14-8 (TRQG)
    Power switch on (READY)
    Steering wheel not being turned (without load)
    2.3 to 2.7 V
    Power switch on (READY)
    Steering wheel being turned to the right with vehicle stopped
    2.5 to 3.8 V
    Power switch on (READY)
    Steering wheel being turned to the left with vehicle stopped
    1.2 to 2.5 V
    z14-7 (TRQ2) - z14-8 (TRQG)
    Power switch on (READY)
    Steering wheel not being turned (without load)
    2.3 to 2.7 V
    Power switch on (READY)
    Steering wheel being turned to the right with vehicle stopped
    1.2 to 2.5 V
    Power switch on (READY)
    Steering wheel being turned to the left with vehicle stopped
    2.5 to 3.8 V

  1. Under each condition, measure the voltage at terminals TRQ1 and TRQ2, and calculate the sum.

    Standard Voltage:
    Inspection Item
    Condition (Steering Wheel Position)
    Specified Condition
    Sum of voltage between z14-5 (TRQ1) and z14-8 (TRQG) and voltage between z14-7 (TRQ2) and z14-8 (TRQG)
    Power switch on (READY)
    Steering wheel not being turned (without load)
    Between 4.75 V and 5.25 V
    Power switch on (READY)
    Steering wheel being turned to the right with vehicle stopped
    Power switch on (READY)
    Steering wheel being turned to the left with vehicle stopped

    Text in Illustration 
    *1
    Component with harness connected
    (Power Steering ECU Assembly)



NG
REPLACE ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY (Click here)
OK

REPLACE POWER STEERING ECU ASSEMBLY (Click here)