DTC P0607 Control Module Performance |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0607 | Either of the following conditions is met (1 trip detection logic):
|
|
| Related DTCs | P0607: Control Module Performance |
| Required Sensors/Components (Main) | ECM |
| Required Sensors/Components (Related) | Heated oxygen sensor |
| Frequency of Operation | Continuous |
| Duration | 60 seconds |
| MIL Operation | Immediately |
| Sequence of Operation | None |
| Monitor runs whenever the following DTCs are not stored | None |
| Engine | Running |
| Estimated heated oxygen sensor temperature | 450 to 750°C (842 to 1382°F) |
| Heated oxygen sensor transistors | Fail |

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK ANY OTHER DTCS OUTPUT |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P0607 and P0136, P0137 or P0138 are output | A |
| DTC P0607 is output | B |
|
| ||||
| A | |
| 2.INSPECT DTC (P0136, P0137 OR P0138) |
Refer to the P0136, P0137 or P0138 flowchart.
|
| ||||
| 3.CHECK FOR EXHAUST GAS LEAK |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Turn the Techstream on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine.
Allow the engine to idle and rev the engine.
Check for exhaust gas leaks around the heated oxygen sensor.
If any exhaust gas leaks are present, repair them and proceed to "Perform Confirmation Driving Pattern". If no exhaust gas leaks are present, proceed to "Perform Confirmation Driving Pattern".
| NEXT | |
| 4.PERFORM CONFIRMATION DRIVING PATTERN |

Connect the Techstream to the DLC3.
Turn the power switch on (IG) and turn the Techstream on.
Clear the DTC (Click here).
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine.
Warm up the engine until the engine coolant temperature becomes 75°C (167°F) or more.
Perform the driving pattern.
Accelerate the vehicle to 50 mph (80 km/h) and stop the vehicle.
Drive the vehicle between 38 and 50 mph (60 and 80 km/h) for 5 minutes.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P0607 and P0136, P0137 or P0138 are output | A |
| Only P0607 is output | B |
| DTC is not output | C |
|
| ||||
|
| ||||
| A | |
| 5.INSPECT DTC (P0136, P0137 OR P0138) |
Refer to the P0136, P0137 or P0138 flowchart.
| NEXT | |
| 6.INSPECT ECM |
Clear the DTC (Click here).
Stop the engine and wait for 30 minutes.
Connect the Techstream to the DLC3.
Turn the power switch on (IG) and turn the Techstream on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine and allow it to idle for 2 minutes.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Check the DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P0607 is output | B |
|
| ||||
| A | ||
| ||