Home › Engine / Hybrid System › 2ZR-FXE FUEL › FUEL TANK

FUEL TANK > REMOVAL

for Preparation Click here



1. REMOVE FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE
  1. Remove the fuel suction tube assembly with pump and gauge (Click here).



2. DRAIN FUEL


3. REMOVE REAR FLOOR SIDE MEMBER COVER LH (w/ Floor Under Cover)


    C207250
  1. Remove the nut, 2 bolts and rear floor side member cover LH.



4. REMOVE REAR FLOOR SIDE MEMBER COVER RH (w/ Floor Under Cover)


    C207251
  1. Remove the 3 bolts.

  1. Disengage the clip and remove the rear floor side member cover RH.



5. REMOVE REAR SUSPENSION BRACE SUB-ASSEMBLY


  1. Remove the 4 bolts.


    C207257

  1. Disengage the clip and remove the rear suspension brace sub-assembly.



6. REMOVE REAR FLOOR STEP UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)


    A212659E01
  1. Remove the 5 clips (A) and nut.

  1. Disconnect the 3 clips (B) and remove the rear floor step under cover sub-assembly.



7. REMOVE NO. 1 FUEL TANK PROTECTOR


    A216429
  1. Remove the 3 bolts and the No. 1 fuel tank protector.



8. DISCONNECT FUEL CUT-OFF TUBE


    A216433E01
  1. Disconnect the fuel cut-off tube from the charcoal canister assembly.
    Text in Illustration 
    *1
    Retainer

    HINT:
    Do not remove the retainer.

    NOTICE:
    1. Remove any dirt or foreign matter on the fuel cut-off tube connector before performing this work.
    2. Do not allow any scratches or foreign matter on the parts when disconnecting them as the fuel cut-off tube connector has an O-ring that seals the pipe.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the fuel cut-off tube.
    5. Protect the disconnected part by covering it with a plastic bag after disconnecting the fuel cut-off tube.
    6. If the vent hose connector and pipe are stuck, push and pull on them to release.



9. DISCONNECT FUEL TANK BREATHER TUBE


    A216434E01
  1. Pinch the tabs of the retainer to remove the lock claws and pull it down as shown in the illustration.
    Text in Illustration 
    *1
    Retainer
    *2
    Quick Connector
    *3
    Pipe
    *4
    O-ring

  1. Pull out the fuel tank breather tube.

    NOTICE:
    1. Check that there is no dirt or foreign matter around the connector before this operation and clean the connector as necessary.
    2. It is necessary to prevent dirt or foreign matter from entering the connector. If mud or dirt gets in the connector, the O-rings may not seal properly.
    3. Do not use any tools in this operation.
    4. Do not bend, kink or twist the nylon tube. Protect the connector by covering it with a plastic bag.
    5. When the pipe and connector are stuck, push and pull the connector to release and pull the connector out carefully.



10. DISCONNECT FUEL TANK TO FILLER PIPE HOSE


    A216436E01
  1. Pull the tabs of the retainer to disengage the lock claws and pull it down as shown in the illustration
    Text in Illustration 
    *1
    Retainer

  1. Pull out the fuel tank to filler pipe hose.

    NOTICE:
    1. Check that there is no dirt or foreign matter around the connector before this operation and clean the connector as necessary.
    2. It is necessary to prevent dirt or foreign matter from entering the connector. If dirt or foreign matter gets in the connector, the O-rings may not seal properly.
    3. Do not use any tools in this operation.
    4. Do not bend, kink or twist the nylon tube. Protect the connector by covering it with a plastic bag.
    5. When the pipe and connector are stuck, push and pull the connector to release and pull the connector out carefully.



11. REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY


A216435E01
Text in Illustration 
*1
Retainer
*2
Quick Connector
*3
Pipe
*4
O-ring
  1. Pinch the tabs of the retainer to remove the lock claws and pull it down as shown in the illustration.

  1. Pull out and remove the fuel tank main tube sub-assembly.

    NOTICE:
    1. Check that there is no dirt or foreign matter around the connector before this operation and clean the connector as necessary.
    2. It is necessary to prevent dirt or foreign matter from entering the connector. If dirt or foreign matter gets in the connector, the O-rings may not seal properly.
    3. Do not use any tools in this operation.
    4. Do not bend, kink or twist the nylon tube. Protect the connector by covering it with a plastic bag.
    5. When the pipe and connector are stuck, push and pull the connector to release and pull the connector out carefully.



12. REMOVE FUEL TANK ASSEMBLY


    A216430
  1. Remove the 2 bolts and disconnect the parking brake cable assembly.



    A216431
  1. Support the fuel tank using an engine lifter.



    A216432
  1. Remove the 4 set bolts of the 2 fuel tank bands.

  1. Lower the engine lifter to remove the fuel tank.

    NOTICE:
    1. Slowly operate the engine lifter to lower the fuel tank.
    2. Do not drop the fuel tank.
    3. When removing the fuel tank, tilt it slightly to prevent it from interfering with the suspension arm or other surrounding parts.



13. REMOVE NO. 1 FUEL TANK CUSHION


    A245571E01
  1. Remove the 3 No. 1 fuel tank cushions.
    Text in Illustration 
    *1
    No. 1 Fuel Tank Cushion



14. REMOVE FUEL TANK COVER VENT CASE SUB-ASSEMBLY


    A245572
  1. Remove the 2 fuel tank cover vent case sub-assemblies.