Home › Engine / Hybrid System › 2ZR-FXE LUBRICATION › OIL PUMP

OIL PUMP > INSTALLATION

for Preparation Click here



1. INSTALL OIL PUMP ASSEMBLY


    A150895
  1. Install the oil pump with the 3 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }



2. INSTALL NO. 2 OIL PAN SUB-ASSEMBLY
  1. Remove any old packing material and be careful not to drop any oil on the contact surfaces of the cylinder block and oil pan.



    A150920E06
  1. Apply a continuous bead of seal packing (Diameter 4.0 mm (0.157 in.)) as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. Remove any oil from the contact surfaces.
    2. Install the oil pan within 3 minutes after applying seal packing.
    3. Do not start the engine for at least 2 hours after installing the oil pan.



    A150894
  1. Install the No. 2 oil pan with the 10 bolts and 2 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



3. INSTALL OIL PAN DRAIN PLUG


    A150893
  1. Install a new gasket and the drain plug.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



4. INSTALL CRANKSHAFT TIMING GEAR KEY


    A150910
  1. Using a plastic-faced hammer, tap in the 2 crankshaft timing gear keys.

    HINT:
    Tap in the crankshaft timing gear keys until they contact the crankshaft as shown in the illustration.



5. INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE


    A150874
  1. Install the crankshaft position sensor plate with the "F" mark facing forward.



6. INSTALL NO. 2 CHAIN SUB-ASSEMBLY
  1. Temporarily install the crankshaft pulley bolt.



    A218459
  1. Turn the crankshaft counterclockwise to position the timing gear key to the 9 o'clock position.

  1. Turn the drive shaft so that the cutout faces the 12 o'clock position.



    A165306E02
  1. Align the yellow mark links with the timing marks of each gear as shown in the illustration.
    Text in Illustration 
    *1
    Front
    *2
    Mark Plate (Yellow)
    *3
    Timing Mark
    *4
    Oil Pump Drive Gear
    *5
    Oil Pump Drive Shaft Gear

    HINT:
    Be sure to position the mark plate at the front of the engine.

  1. Install the sprockets onto the crankshaft and oil pump shaft with the chain on the gears.

  1. Temporarily tighten the oil pump drive shaft gear with the nut.



    A218086
  1. Insert the damper spring into the adjusting hole, and then install the chain tensioner plate with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Temporarily tighten the crankshaft pulley with the bolt.



    A218083E01
  1. Using SST, install the oil pump drive shaft gear nut while holding the crankshaft pulley.

    SST
    09213-58014   (91551-80840)
    09330-00021  

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

  1. Remove the crankshaft pulley and bolt.



7. INSTALL CRANKSHAFT TIMING SPROCKET


    A218082
  1. Install the crankshaft timing sprocket.



8. INSTALL NO. 1 CHAIN VIBRATION DAMPER


    A217740
  1. Install the chain vibration damper with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



9. SET NO. 1 CYLINDER TO TDC / COMPRESSION


    A221683E01
  1. Temporarily install the crankshaft pulley bolt.
    Text in Illustration 
    *1
    Timing Gear Key

  1. Turn the crankshaft to position the timing gear key to the top.



    A262288E01
  1. Check that the timing marks on the camshaft timing gear and camshaft timing sprocket are aligned as shown in the illustration.
    Text in Illustration 
    *1
    Timing Mark (Rectangle)
    *2
    Timing Mark
    *3
    Mark (Circle)

    HINT:
    There are 3 marks on the camshaft timing sprocket. Make sure that the timing mark (rectangle) is at the top.

  1. Remove the crankshaft pulley bolt.



10. INSTALL CHAIN SUB-ASSEMBLY


    A262289E01
  1. Align the mark plate (orange) with the timing mark as shown in the illustration and install the chain.
    Text in Illustration 
    *1
    Mark Plate (Orange)
    *2
    Timing Mark (Rectangle)
    *3
    Mark (Circle)
    *a
    Place the Chain on the Sprocket
    *b
    Pass the Chain through the Damper

    HINT:
    1. There are 3 marks on the camshaft timing sprocket. Make sure to align the mark plate with the timing mark (rectangle).
    2. Be sure to position the mark plate at the front of the engine.
    3. The mark plate on the camshaft side is colored orange.
    4. Do not pass the chain around the sprocket of the camshaft timing gear. Only place it on the sprocket.
    5. Pass the chain through the No. 1 vibration damper.



    A150936
  1. Place the chain on the crankshaft without passing it around the shaft.



    A214963E04
  1. Hold the hexagonal portion of the camshaft with a wrench and turn the camshaft timing gear counterclockwise to align the mark plate (orange) and timing mark, and then install the chain.
    Text in Illustration 
    *1
    Mark Plate (Orange)
    *2
    Timing Mark
    *a
    Tension the Chain

  1. Hold the hexagonal portion of the camshaft with a wrench and turn the camshaft timing gear counterclockwise to align the mark plate (orange) and timing mark, and then install the chain.

  1. Hold the hexagonal portion of the camshaft with a wrench and turn the camshaft timing gear clockwise.

    HINT:
    To tension the chain, slowly turn the camshaft timing gear clockwise to prevent the chain from being misaligned.



    A150939E06
  1. Align the mark plate (yellow) and timing mark and install the chain to the crankshaft timing gear.
    Text in Illustration 
    *1
    Mark Plate (Yellow)
    *2
    Timing Mark



11. CHECK NO. 1 CYLINDER TO TDC / COMPRESSION


  1. Check each timing mark at TDC/compression.


    A262290E01


    Text in Illustration 
    *1
    Timing Mark
    *2
    Mark Plate (Orange)
    *3
    Mark Plate (Yellow)
    *4
    Timing Mark (Rectangle)
    *5
    Mark (Circle)
    -
    -

    HINT:
    There are 3 marks on the camshaft timing sprocket. Make sure that the timing mark (rectangle) is at the top.



12. INSTALL CHAIN TENSIONER SLIPPER


    A214929
  1. Install the chain tensioner slipper to the cylinder block.



13. INSTALL NO. 2 CHAIN VIBRATION DAMPER


    A214931
  1. Install the No. 2 chain vibration damper with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



14. INSTALL TIMING CHAIN COVER OIL SEAL


    A150934E01
  1. Using SST, tap in a new oil seal until its surface is flush with the timing chain cover edge.

    SST
    09223-22010  

    NOTICE:
    1. Keep the lip free from foreign matter.
    2. Do not tap on the oil seal at an angle.
    3. Make sure that the oil seal edge does not stick out of the timing chain case.

    HINT:
    Tap in the oil seal so that it is positioned within 1.0 mm from the edge of the timing chain case.

  1. Apply MP grease to the lip of the oil seal.



15. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY


  1. Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the timing chain cover, cylinder head, and cylinder block.


    A214951E01



    A214924
  1. Install 3 new O-rings.



  1. Apply seal packing as shown in the illustration.


    A214953E01

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Seal diameter:
    5.0 mm (0.197 in.)

    NOTICE:
    1. Remove any oil from the contact surfaces.
    2. Install the chain cover within 3 minutes after applying seal packing.
    3. Do not start the engine for at least 2 hours after installing the timing chain cover sub-assembly.



  1. Apply seal packing to the timing chain cover in a line as shown in the following illustration.

    NOTICE:
    1. When the contact surfaces are wet, wipe them with oil-free cloth before applying seal packing.
    2. Install the chain cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
    3. Do not start the engine for at least 2 hours after installation.



    A214952E01


    Seal Packing:

    Item
    Seal Packing
    Dashed line
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
    Continuous line
    Alternate long and short dashed line
    Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent


    Application Specification:

    Area
    Seal Packing Diameter
    Distance from Edge of Cover to:
    Seal Packing Application Length
    Distance from Top of Cover to Top of Seal Packing
    Dashed line
    2.5 to 3.0 mm (0.0984 to 0.118 in.)
    Center of seal packing
    2.5 mm (0.0984 in.)
    -
    -
    Continuous line
    4.5 to 5.5 mm (0.177 to 0.217 in.) or 7.0 to 8.0 mm (0.276 to 0.315 in.)
    -
    -
    -
    Alternate long and short dashed line
    4.0 mm (0.157 in.)
    Center of seal packing
    3.0 mm (0.118 in.)
    -
    -
    A - A
    2.5 to 3.0 mm (0.0984 to 0.118 in.)
    Center of seal packing
    2.5 mm (0.0984 in.)
    -
    -
    B - B
    4.5 to 5.5 mm (0.177 to 0.217 in.)
    Opposite edge of seal packing
    5.0 mm (0.197 in.)
    -
    -
    C - C
    7.0 to 8.0 mm (0.276 to 0.315 in.)
    Opposite edge of seal packing
    7.5 mm (0.295 in.)
    -
    -
    F
    4.5 to 5.5 mm (0.177 to 0.217 in.)
    -
    15.5 mm (0.610 in.)
    50.4 mm (1.98 in.)
    G
    4.5 to 5.5 mm (0.177 to 0.217 in.)
    -
    10.3 mm (0.406 in.)
    143.1 mm (5.63 in.)
    H
    7.0 to 8.0 mm (0.276 to 0.315 in.)
    -
    19.5 mm (0.768 in.)
    153.4 mm (6.04 in.)
    I
    4.5 to 5.5 mm (0.177 to 0.217 in.)
    -
    16.0 mm (0.630 in.)
    385.8 mm (1.27 ft.)
    J
    4.5 to 5.5 mm (0.177 to 0.217 in.)
    -
    18.6 mm (0.732 in.)
    51.4 mm (2.02 in.)
    K
    4.5 to 5.5 mm (0.177 to 0.217 in.)
    -
    25.3 mm (0.996 in.)
    121.9 mm (4.80 in.)
    L
    7.0 to 8.0 mm (0.276 to 0.315 in.)
    -
    25.8 mm (1.02 in.)
    147.2 mm (5.80 in.)
    M
    4.5 to 5.5 mm (0.177 to 0.217 in.)
    -
    5.1 mm (0.201 in.)
    173.0 mm (6.81 in.)
    N
    4.5 to 5.5 mm (0.177 to 0.217 in.)
    -
    14.6 mm (0.575 in.)
    385.8 mm (1.27 ft.)
    O
    4.0 mm (0.157 in.)
    Center of seal packing
    3.0 mm (0.118 in.)
    -
    -

    NOTICE:
    1. When the contact surfaces are wet, wipe them with oil-free cloth before applying seal packing.
    2. Install the timing chain cover within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.
    3. After applying seal packing to the timing chain cover, install the engine mounting bracket and oil filter bracket within 10 minutes.
    4. Do not add engine oil for at least 2 hours after installation.

  1. Clean the bolt and fitting hole.

  1. Install the timing chain cover.



    A214919
  1. Temporarily tighten the engine mounting bracket RH with the 3 bolts.

    NOTICE:
    1. Install the mounting bracket within 10 minutes after installing the chain cover.
    2. Do not start the engine for at least 2 hours after installation.

    Bolt Length:
    Item
    Length
    Bolt
    80 mm (3.15 in.)



    A214921
  1. Install 2 new O-rings.



    A214920
  1. Temporarily tighten the oil filter bracket with the 4 bolts.

    NOTICE:
    1. Install the oil filter bracket within 10 minutes after installing the chain cover.
    2. Do not start the engine for at least 2 hours after installation.

    Bolt Length:
    Item
    Length
    Bolt
    35 mm (1.38 in.)



  1. Install the timing chain cover with the 25 bolts and seal washer as shown in the illustration.


    A214954E02


    Text in Illustration 
    *1
    Seal Washer
    -
    -

    Torque:
    Bolt A, E, F:
    26 N*m{ 260 kgf*cm , 19 ft.*lbf }
    Bolt B, C:
    51 N*m{ 520 kgf*cm , 38 ft.*lbf }
    Bolt D:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    1. Apply adhesive 1324 to screw part of the bolt F.
    2. When the contact surfaces are wet, wipe them with oil-free cloth before applying seal packing.
    3. Install the chain cover within 3 minutes and tighten the bolts within 15 minutes after applying the seal packing.
    4. Do not add engine oil for at least 2 hours after installing the chain cover.
    5. Do not start the engine for at least 2 hours after installing the chain cover.

    Bolt Length:
    Item
    Length
    Bolt A, F
    35 mm (1.38 in.)
    Bolt B
    55 mm (2.16 in.)
    Bolt C
    80 mm (3.15 in.)
    Bolt D
    40 mm (1.57 in.)
    Bolt E
    55 mm (2.16 in.)



16. INSTALL CRANKSHAFT PULLEY
  1. Align the pulley set key with the key groove of the pulley.



    A213054E02
  1. Using SST, hold the pulley in place and tighten the bolt.
    Text in Illustration 
    *a
    Hold
    *b
    Turn

    SST
    09213-58014   (91551-80840)
    09330-00021  

    Torque:
    190 N*m{ 1937 kgf*cm , 140 ft.*lbf }



17. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY


    A162975E02
  1. Release the cam, and then fully push in the plunger and engage the hook to the pin so that the plunger is in the position shown in the illustration.
    Text in Illustration 
    *1
    Cam
    *2
    Pin
    *3
    Hook
    *a
    Push
    *b
    Raise
    *c
    CORRECT
    *d
    INCORRECT

    NOTICE:
    Make sure that the cam engages the first tooth of the plunger to allow the hook to pass over the pin.



    A214955
  1. Install a new gasket, the bracket and chain tensioner with the 2 nuts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

    NOTICE:
    If the hook releases the plunger while the chain tensioner is being installed, set the hook again.



    A214956E02
  1. Rotate the crankshaft counterclockwise slightly and check that the hook becomes released.
    Text in Illustration 
    *1
    Pin
    *2
    Hook
    *a
    Push
    *b
    Turn
    *c
    Disconnect



    A214957E02
  1. Turn the crankshaft clockwise and check that the plunger is extended.
    Text in Illustration 
    *1
    Plunger
    *a
    Turn
    *b
    Plunger Extended



18. INSTALL SPARK PLUG TUBE GASKET


    A153838E04
  1. Using a cutter knife, cut off the seal part of the removed gasket.
    Text in Illustration 
    V100155
    Part to Cut Off



    A214958E02
  1. Using a hammer and the plug tube gasket which has had the sealing part cut off, uniformly tap in a new plug tube gasket all the way.
    Text in Illustration 
    *1
    Plug Tube Gasket without Sealing Part
    *2
    New Plug Tube Gasket

    NOTICE:
    1. Keep the lip free of foreign matter.
    2. Do not tap in the plug tube gasket.

    HINT:
    If a plug tube gasket that will be used to install a new gasket is deformed, and cannot be positioned on a new gasket, correct the deformation using pliers.

  1. Return the claws of the ventilation baffle plate to their original positions.



19. INSTALL CYLINDER HEAD COVER GASKET


    A215254E05
  1. Apply seal packing (Diameter 4.0 mm (0.157 in.)) to the cylinder block as shown in the illustration.
    Text in Illustration 
    *1
    Cylinder Block
    V100135
    Engine Front

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    Remove any oil from the cylinder block.



    A150921E03
  1. Place a new cylinder head gasket on the cylinder block with the Lot No. stamp facing upward.
    Text in Illustration 
    *a
    Lot No.
    V100135
    Engine Front

    NOTICE:
    Install the cylinder head gasket within 3 minutes after applying seal packing.



    A214975E04
  1. Apply seal packing (Diameter 4.0 mm (0.157 in.)) to the new cylinder head gasket as shown in the illustration.
    Text in Illustration 
    *1
    Cylinder Head Gasket
    V100135
    Engine Front

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. Remove any oil from the cylinder head gasket and cylinder head.
    2. Install the cylinder head gasket within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.



    A214976E02
  1. After tightening the cylinder head bolts, wipe off the seal packing material seeped out from the contact surfaces between the cylinder head and cylinder block.
    Text in Illustration 
    *a
    Before wiping off:
    *b
    After wiping off:



20. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

HINT:
  1. Perform "Inspection After Repair" after replacing the cylinder head sub-assembly (Click here).
  2. The cylinder head bolts are tightened in 3 progressive steps.

  1. Place the cylinder head on the cylinder block.

    NOTICE:
    1. Make sure that no oil is on the mounting surface of the cylinder head.
    2. Place the cylinder head on the cylinder block gently in order not to damage the gasket with the bottom part of the head.

  1. Install the plate washers to the cylinder head bolts.

  1. Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.



    A150891E02
  1. Step 1:

    1. Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 10 cylinder head bolts in several steps, in the sequence shown in the illustration.

      Torque:
      49 N*m{ 500 kgf*cm , 36 ft.*lbf }

      NOTICE:
      Do not drop the plate washers into the cylinder head.



    A156439E06
  1. Step 2:
    Text in Illustration 
    *a
    Paint Mark
    V100136
    Engine Front

    1. Mark each cylinder head bolt head with paint as shown in the illustration.

    2. Tighten the cylinder head bolts 90° in the sequence shown in step 1.

  1. Step 3:

    1. Tighten the cylinder head bolts another 45° in the sequence shown in step 1.

  1. Check that the paint mark is now at a 135° angle to the front.



21. INSTALL WATER INLET WITH THERMOSTAT SUB-ASSEMBLY


    A216666
  1. Install a new gasket on the water inlet with thermostat sub-assembly.



    A216071
  1. Install the water inlet with thermostat sub-assembly with the 2 nuts and bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



    A216072E01
  1. Connect the No. 2 radiator hose and No. 3 water by-pass hose.
    Text in Illustration 
    *1
    No. 2 Radiator Hose
    *2
    No. 3 Water By-pass Hose



22. INSTALL FUEL INJECTOR ASSEMBLY

HINT:
Perform "Inspection After Repair" after replacing a fuel injector assembly (Click here).



    A153011E06
  1. Install a new insulator and O-ring to each fuel injector assembly.
    Text in Illustration 
    *1
    O-ring
    *2
    Insulator

  1. Apply a light coat of gasoline or spindle oil to the contact surfaces of the new O-ring on each fuel injector assembly.



    A173350
  1. While turning the fuel injector assembly left and right, install it onto the fuel delivery pipe sub-assembly.

    NOTICE:
    1. Do not damage the fuel injector assembly or O-ring.
    2. Do not twist the O-ring.
    3. After installing each fuel injector, check that it turns smoothly. If not, replace the O-ring with a new one.



23. INSTALL NO. 1 DELIVERY PIPE SPACER


    A245591E01
  1. Install the 2 No. 1 delivery pipe spacers onto the cylinder head.
    Text in Illustration 
    *a
    Delivery Pipe Side
    *b
    Cylinder Head Side

    NOTICE:
    Install the No. 1 delivery pipe spacers in the correct direction.



24. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY


    A216400
  1. Install the fuel delivery pipe sub-assembly with the 4 fuel injector assemblies and install the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    NOTICE:
    1. Do not drop the fuel injectors when installing the fuel delivery pipe sub-assembly.
    2. Check that the fuel injector assemblies rotate smoothly after installing the fuel delivery pipe sub-assembly.



    A216399
  1. Install the bolt to secure the fuel delivery pipe sub-assembly.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



25. INSTALL FUEL VAPOR FEED PIPE


    A218073
  1. Install the fuel vapor feed pipe with the bolt.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



26. INSTALL INTAKE MANIFOLD
  1. w/ Stud Bolt:

    1. Using an E6 "TORX" socket wrench, install the 2 stud bolts to the intake manifold.

      Torque:
      5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

      HINT:
      If a stud bolt is deformed or the threads are damaged, replace the stud bolt.

  1. Install a new No. 1 intake manifold to head gasket to the intake manifold.



    A212684
  1. Install the intake manifold with the 2 bolts and 2 nuts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }



    A212683
  1. Connect the fuel vapor feed hose and ventilation hose to the intake manifold.

  1. Apply a light coat of engine oil to a new O-ring.

  1. Install the O-ring to the engine oil level dipstick guide sub-assembly.



    A212681E02
  1. Install the engine oil level dipstick guide sub-assembly with the 2 bolts and connect the wire harness clamp.

    Torque:
    Bolt (A):
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }
    Bolt (B):
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Install the engine oil level dipstick.



    A212682
  1. Connect the 2 wire harness clamps and 3 connectors.



27. INSTALL EGR COOLER SUB-ASSEMBLY


    A297470
  1. Temporarily install a new gasket and the EGR valve assembly to the EGR with cooler pipe sub-assembly with the 2 nuts.

  1. Install a new gasket and set the EGR valve with cooler assembly in place.



  1. Using an E8 "TORX" socket wrench, install the 4 stud bolts.


    A297489E04


    Text in Illustration 
    *a
    Stud Bolt A
    *b
    Stud Bolt B
    *c
    Stud Bolt C
    -
    -

    Torque:
    Stud Bolt A and Stud Bolt B:
    9.5 N*m{ 97 kgf*cm , 84 in.*lbf }
    Stud Bolt C:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

    If a stud bolt is deformed or the threads are damaged, replace it.



  1. Temporarily install the 2 nuts (B), 2 nuts (C) and bolt.

    HINT:
    The type B and type C of the nut (C) is non-reusable.



    A307474E02


    Text in Illustration 
    *A
    Type A
    *B
    Type B
    *C
    Type C
    -
    -
    *a
    Nut A
    *b
    Nut B
    *c
    Nut C
    *d
    Bolt

  1. Tighten the 2 nuts (A).

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Tighten the 2 nuts (B) and bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    NOTICE:
    Make sure that all installation surfaces of the EGR valve with cooler assembly are in even contact when tightening the bolt and nuts.

  1. Tighten the 2 nuts (C).

    Torque:
    Type A:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }
    Type B:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }
    Type C:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



    A212666
  1. Connect the 4 water hoses to the EGR valve with cooler assembly and slide the 4 clips to secure them.

  1. Engage the wire harness clamp.

  1. Connect the EGR valve assembly connector.



28. INSTALL EGR VALVE ASSEMBLY

HINT:
Perform the "Inspection After Repair" after replacing the EGR valve assembly (Click here).



    A297470
  1. Temporarily install a new gasket and the EGR valve assembly to the EGR with cooler pipe sub-assembly with the 2 nuts.

  1. Install a new gasket and set the EGR valve with cooler assembly in place.



  1. Using an E8 "TORX" socket wrench, install the 4 stud bolts.


    A297489E04


    Text in Illustration 
    *a
    Stud Bolt A
    *b
    Stud Bolt B
    *c
    Stud Bolt C
    -
    -

    Torque:
    Stud Bolt A and Stud Bolt B:
    9.5 N*m{ 97 kgf*cm , 84 in.*lbf }
    Stud Bolt C:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

    If a stud bolt is deformed or the threads are damaged, replace it.



  1. Temporarily install the 2 nuts (B), 2 nuts (C) and bolt.

    HINT:
    The type B and type C of the nut (C) is non-reusable.



    A307474E02


    Text in Illustration 
    *A
    Type A
    *B
    Type B
    *C
    Type C
    -
    -
    *a
    Nut A
    *b
    Nut B
    *c
    Nut C
    *d
    Bolt

  1. Tighten the 2 nuts (A).

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Tighten the 2 nuts (B) and bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    NOTICE:
    Make sure that all installation surfaces of the EGR valve with cooler assembly are in even contact when tightening the bolt and nuts.

  1. Tighten the 2 nuts (C).

    Torque:
    Type A:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }
    Type B:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }
    Type C:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



    A212666
  1. Connect the 4 water hoses to the EGR valve with cooler assembly and slide the 4 clips to secure them.

  1. Engage the wire harness clamp.

  1. Connect the EGR valve assembly connector.



29. INSTALL EGR PIPE ASSEMBLY


    A212665
  1. Install 2 new gaskets and EGR pipe assembly with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    Make sure to tighten the 4 bolts evenly until the flanges of the EGR pipe assembly contact with the installation surfaces.



    A212664
  1. Install the wire harness support with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



    A212663
  1. Engage the 2 wire harness clamps.



30. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
  1. Apply a light coat of engine oil to a new O-ring.

  1. Install the O-ring to the engine oil level dipstick guide.



    A213046E01
  1. Install the engine oil level dipstick guide with the 2 bolts.

    Torque:
    Bolt A:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }
    Bolt B:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the clamp to the engine oil level dipstick guide.

  1. Install the engine oil level dipstick.



31. INSTALL THROTTLE BODY ASSEMBLY

HINT:
Perform "Inspection After Repair" after replacing the throttle body assembly (Click here).



  1. Type A:



      A212317E01
    1. Install a new gasket onto the intake manifold.

      HINT:
      Orient the protrusion of the gasket as shown in the illustration.

      Text in Illustration 
      *a
      Protrusion



    2. A212316
    3. Install the throttle body assembly with the 2 bolts and 2 nuts.

      Torque:
      10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    4. Connect the No. 1 water by-pass hose and No. 2 water by-pass hose.

    5. Connect the connector.



  1. Type B:



      A288948E01
    1. Install a new gasket onto the intake manifold.

      HINT:
      Orient the protrusion of the gasket as shown in the illustration.
      Text in Illustration 
      *a
      Protrusion

    2. Install the throttle body assembly with the 4 bolts.

    3. Connect the No. 1 water by-pass hose and No. 2 water by-pass hose.

    4. Connect the connector.



32. INSTALL ENGINE HANGERS


    A214905
  1. Install the No. 1 and No. 2 engine hangers with the 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

    Part Name
    Part No.
    No. 1 engine hanger
    12281-37021
    No. 2 engine hanger
    12282-37011
    Bolt
    91552-81050



33. REMOVE ENGINE ON ENGINE STAND
  1. Remove the engine from the engine stand.

    HINT:
    Perform "Inspection After Repair" after replacing the engine assembly (Click here).



34. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE