Home › Engine / Hybrid System › 2ZR-FXE LUBRICATION › OIL AND OIL FILTER

OIL AND OIL FILTER > REPLACEMENT

for Preparation Click here


CAUTION:
  1. Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.
  2. Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water or waterless hand cleaner to remove any used engine oil thoroughly. Do not use gasoline, thinners, or solvents.
  3. In order to preserve the environment, used oil and used oil filters must be disposed of at designated disposal sites.



1. REMOVE OIL FILTER ELEMENT SERVICE HOLE COVER


    A228174
  1. Remove the 3 clips.



    A228175
  1. Pull the oil filter element service hole cover to open it.

    HINT:
    Fully open the service hole cover and fold it at a 180° angle.



    A228177E01
  1. Using one of the removed clips, secure the service hole cover with it folded at a 180° angle.
    Text in Illustration 
    *1
    Clip



2. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and gasket, and drain the oil into a container.

  1. Clean and install the oil pan drain plug with a new gasket.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



3. REMOVE OIL FILTER CAP ASSEMBLY


    A198241E06
  1. Using SST, loosen the oil filter cap 4 revolutions, align the cap ribs vertically, and drain the remaining engine oil in the oil filter cap.
    Text in Illustration 
    *1
    Oil Filter Bracket Clip
    *a
    Cap Rib

    SST
    09228-06501  

    NOTICE:
    Do not remove the oil filter bracket clip when removing the oil filter cap assembly.

    HINT:
    Set a container below the oil filter cap assembly before loosening the oil filter cap.

  1. Remove the oil filter cap assembly.



    A218052E01
  1. Remove the oil filter element and O-ring from the oil filter cap assembly.
    Text in Illustration 
    *1
    Oil Filter Element
    *2
    O-ring

    NOTICE:
    Do not use any tools to remove the O-ring to prevent damage to the oil filter cap assembly. Be sure to remove it by hand.



4. INSTALL OIL FILTER CAP ASSEMBLY
  1. Clean the inside of the oil filter cap assembly, the threads and O-ring groove.



    A268595E01
  1. Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap assembly.
    Text in Illustration 
    *1
    O-ring
    *a
    Correct
    *b
    Incorrect

    NOTICE:
    1. Be sure to install the O-ring in the proper location, otherwise oil may leak.
    2. Do not twist the O-ring.

  1. Set a new oil filter element in the oil filter cap assembly.

  1. Remove any dirt or foreign matter from the installation surface of the engine.



    A161887
  1. Apply a small amount of engine oil to the O-ring of the oil filter cap assembly again. Align the cutout in the oil filter cap threads 90° to the grooves in the oil filter bracket and temporarily tighten the oil filter cap assembly.

    NOTICE:
    Make sure that the O-ring does not get caught between the parts.



    A283056E01
  1. Using SST, tighten the oil filter cap assembly.
    Text in Illustration 
    *1
    Oil Filter Cap Assembly
    *2
    O-ring
    *3
    Oil Filter Bracket
    *a
    No Gap

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    SST
    09228-06501  

    NOTICE:
    1. After tightening the oil filter cap assembly, make sure that there is no gap and that the O-ring is not protruding.
    2. Do not remove the oil filter bracket clip when installing the oil filter cap assembly.
    3. Do not cross thread the oil filter cap assembly.



5. ADD ENGINE OIL
  1. Add new engine oil and install the oil filler cap.

    Standard Oil Grade 
    Oil Grade
    Oil Viscosity (SAE)
    1. ILSAC multigrade engine oil
    0W-20

    Standard Capacity 
    Item
    Standard Condition
    Drain and refill with oil filter change
    4.2 liters (4.4 US qts, 3.7 lmp. qts)
    Drain and refill without oil filter change
    3.9 liters (4.1 US qts, 3.4 lmp. qts)
    Dry fill
    4.7 liters (5.0 US qts, 4.1 lmp. qts)



6. INSPECT FOR ENGINE OIL LEAK
  1. Put the engine in inspection mode (Click here).

  1. Warm up the engine. Make sure that there are no engine oil leaks from the area that was worked on.



7. INSTALL OIL FILTER ELEMENT SERVICE HOLE COVER


    A228177E01
  1. Remove the clip.
    Text in Illustration 
    *1
    Clip



    A228176
  1. Close the service hole cover.

    HINT:
    1. Push the oil filter element service hole cover towards the vehicle to remove the crease.
    2. If the crease remains, the service hole cover may look as though it does not fit properly after the clips are installed.



    A228174
  1. Install the oil filter element service hole cover with the 3 clips.