Home › Engine / Hybrid System › 2ZR-FXE ENGINE MECHANICAL › ENGINE ASSEMBLY

ENGINE ASSEMBLY > INSTALLATION

for Preparation Click here


HINT:
Perform "Inspection After Repair" after replacing the engine assembly (Click here).



1. INSTALL FLYWHEEL SUB-ASSEMBLY
  1. Gently place the engine assembly onto wood blocks or equivalent.

    NOTICE:
    This step should be done while hanging the engine assembly using the engine hangers and a chain block.

  1. Install the flywheel sub-assembly .



2. INSTALL TRANSMISSION INPUT DAMPER ASSEMBLY
  1. Gently place the engine assembly onto wood blocks or equivalent.

    NOTICE:
    This step should be done while hanging the engine assembly using the engine hangers and a chain block.

  1. Install the transmission input damper assembly .



3. INSTALL HYBRID VEHICLE TRANSAXLE ASSEMBLY
  1. Install the hybrid vehicle transaxle assembly .

    NOTICE:
    Be careful not to apply excess force to the transmission input damper assembly when removing or installing the hybrid vehicle transaxle assembly. If excess force is applied, the transmission input damper assembly may be damaged, or its splines may become misaligned.



4. INSTALL ENGINE WIRE
  1. Install the engine wire to the engine.



5. INSTALL FLYWHEEL HOUSING SIDE COVER


    C209283
  1. Install the flywheel housing side cover.



6. INSTALL STARTER HOLE INSULATOR


    C209282
  1. Install the starter hole insulator with the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



7. INSTALL RADIATOR PIPE


    A213045
  1. Install the radiator pipe with the 2 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

  1. Install the No. 3 radiator hose with the clamp.



8. INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:
Perform this procedure only when replacement of the engine mounting insulator is necessary.



    A276431E01
  1. Position the engine mounting insulator sub-assembly RH as shown in the illustration.

  1. Temporarily install the engine mounting insulator sub-assembly RH with bolt A.

  1. Tighten the 3 bolts to the engine mounting insulator sub-assembly RH in the order the bolt B, bolt C and bolt A.

    Torque:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }

  1. Connect the wire harness clamp to the engine mounting insulator sub-assembly RH.

  1. Install the 2 cooler brackets with the 2 bolts.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



9. INSTALL ENGINE MOUNTING INSULATOR LH

HINT:
Perform this procedure only when replacement of the engine mounting insulator is necessary.



    A215740E01
  1. Temporarily install the engine mounting insulator LH with the bolt A.

  1. Tighten the 4 bolts to the engine mounting insulator LH in the order the bolt C, bolt B, bolt D and bolt A.

    Torque:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }



10. INSTALL REAR ENGINE MOUNTING INSULATOR


    A213044
  1. Install the rear engine mounting insulator to the engine mounting bracket with the bolt.

    Torque:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }

    HINT:
    Perform this procedure only when replacement of the engine mounting insulator is necessary.



11. INSTALL FRONT ENGINE MOUNTING INSULATOR


    A219120
  1. Temporarily install the front engine mounting insulator with the bolt and nut.



12. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE
  1. Set the engine assembly with transaxle on the engine lifter.

    NOTICE:
    1. Install a height adjustment attachment and plate lift attachment onto the engine assembly with transaxle.
    2. Do not position a height adjustment attachment or plate lift attachment onto the front frame assembly.

    HINT:
    Place the engine on wooden blocks or equivalents so that the engine is level.



    A214905
  1. Remove the 2 bolts and 2 engine hangers.



    A216482
  1. Set the engine assembly with transaxle and front suspension crossmember on the engine lifter.

  1. Operate the engine lifter and lift the engine assembly with transaxle and front suspension crossmember to the position where the engine mounting insulators RH and LH can be installed.

    CAUTION:
    Do not raise the engine more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.

    NOTICE:
    1. Make sure that the engine is clear of all wiring and hoses.
    2. While raising the engine into the vehicle, do not allow it to contact the vehicle.

    HINT:
    Perform "Inspection After Repair" after replacing the engine assembly (Click here).



    A213042
  1. Install the front crossmember with the 4 bolts.

    Torque:
    96 N*m{ 979 kgf*cm , 71 ft.*lbf }



    A219121
  1. Install the front engine mounting insulator to the front crossmember with the 2 bolts.

    Torque:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }



    A213043
  1. Install the engine mounting insulator LH with the bolt and nut.

    Torque:
    56 N*m{ 571 kgf*cm , 41 ft.*lbf }

    NOTICE:
    When installing the engine mounting insulator, tighten the nut while holding the bolt.



    A158372E01
  1. Install the engine mounting insulator sub-assembly RH with the bolt and 2 nuts.

    Torque:
    Nut A:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }
    Nut B:
    52 N*m{ 530 kgf*cm , 38 ft.*lbf }
    Bolt:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }



    A213041
  1. Tighten the front engine mounting insulator with the bolt and nut.

    Torque:
    145 N*m{ 1479 kgf*cm , 107 ft.*lbf }



13. INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY


    C205602
  1. Support the front suspension crossmember with a transmission jack.



  1. While inserting SST into the reference holes on the front suspension crossmember RH and LH alternately, tighten 2 new bolts A, 2 bolts B, C and 2 nuts D, E on the RH and LH sides to the respective specified torque in several steps.


    C206981E01

    SST
    09670-00020  

    Torque:
    Bolt A:
    137 N*m{ 1397 kgf*cm , 101 ft.*lbf }
    Bolt B, C, Nut D, E:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }

    NOTICE:
    Temporarily tighten bolt B, and then fully tighten the 2 bolts and 2 nuts in the order of C, E, D, and B.



    C205596
  1. Install the 2 wire harness clamp brackets with the 2 bolts.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }



14. INSTALL FRONT SUSPENSION MEMBER REAR BRACE LH


    C234406E01
  1. Install the front suspension member rear brace LH with the 2 bolts B, a new bolt A.

    Torque:
    Bolt A:
    137 N*m{ 1397 kgf*cm , 101 ft.*lbf }
    Bolt B:
    93 N*m{ 948 kgf*cm , 69 ft.*lbf }

  1. Install the clip.



15. INSTALL FRONT SUSPENSION MEMBER REAR BRACE RH

HINT:
Perform the same procedure as for the LH side.



16. INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH


    C205598E01
  1. Install the rear side rail reinforcement sub-assembly LH with the 4 bolts.

    Torque:
    Bolt A, D:
    96 N*m{ 979 kgf*cm , 71 ft.*lbf }
    Bolt B, C:
    99 N*m{ 1010 kgf*cm , 73 ft.*lbf }

    NOTICE:
    Temporarily tighten bolts A and B, and then fully tighten the 4 bolts in the order of C, B, D and A.



17. INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH


    C205612E01
  1. Install the rear side rail reinforcement sub-assembly RH with the 4 bolts.

    Torque:
    Bolt A, D:
    96 N*m{ 979 kgf*cm , 71 ft.*lbf }
    Bolt B, C:
    99 N*m{ 1010 kgf*cm , 73 ft.*lbf }

    NOTICE:
    Temporarily tighten bolts A and B, and then fully tighten the 4 bolts in the order of C, B, D and A.



18. INSTALL FRONT ENGINE MOUNTING BRACKET LOWER REINFORCEMENT


    C249903E01
  1. Install the front engine mounting bracket lower reinforcement with the 2 bolts.

    Torque:
    Bolt A:
    96 N*m{ 979 kgf*cm , 71 ft.*lbf }
    Bolt B:
    99 N*m{ 1010 kgf*cm , 73 ft.*lbf }



19. INSTALL FRONT DRIVE SHAFT HOLE SNAP RING LH
  1. Install a new front drive shaft hole snap ring to the front drive inboard joint assembly.

    HINT:
    Face the end gap of the front drive inboard joint hole snap ring downward.



20. INSTALL FRONT DRIVE SHAFT HOLE SNAP RING RH

HINT:
Perform the same procedure as for the LH side.



21. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH


    C208486
  1. Align the inboard joint splines, and using a brass bar and a hammer, install the front drive shaft assembly.

    NOTICE:
    1. Face the end gap of the front drive shaft hole snap ring downward.
    2. Do not damage the transaxle case oil seal.
    3. Do not damage the inboard joint boot.
    4. Make sure to center the front drive shaft assembly during installation to prevent damage to the front drive shaft hole snap ring.

    HINT:
    Confirm whether the drive shaft is securely driven in by checking the reaction force and sound.



    C208473E01
  1. Align the matchmarks and install the front drive shaft assembly to the front axle hub sub-assembly.
    Text in Illustration 
    *1
    Matchmark



22. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.



23. INSTALL FRONT NO. 1 LOWER SUSPENSION ARM SUB-ASSEMBLY LH


    C205578
  1. Install the front No. 1 lower suspension arm sub-assembly to the front lower ball joint with the bolt and 2 nuts.

    Torque:
    89 N*m{ 908 kgf*cm , 66 ft.*lbf }



24. INSTALL FRONT NO. 1 LOWER SUSPENSION ARM SUB-ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.



25. INSTALL FRONT STABILIZER LINK ASSEMBLY LH


    C205585
  1. Install the front stabilizer link assembly to the front shock absorber with coil spring with the nut.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud bolt.



26. INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.



27. CONNECT TIE ROD END SUB-ASSEMBLY LH


    C151407
  1. Connect the tie rod end sub-assembly LH to the steering knuckle with the nut.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

    NOTICE:
    Further tighten the nut up to 60° if the holes for the clip are not aligned.

  1. Install a new clip.



28. CONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.



29. INSTALL FRONT SPEED SENSOR LH


    C208047
  1. Install the front speed sensor and front flexible hose to the front shock absorber with the bolt and clamp.

    Torque:
    19 N*m{ 192 kgf*cm , 14 ft.*lbf }

    NOTICE:
    Do not twist the front speed sensor when installing it.

    HINT:
    Install the font flexible hose first and then the speed sensor harness bracket.



    C130480
  1. Install the front speed sensor to the steering knuckle with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    Do not twist the front speed sensor when installing it.



30. INSTALL FRONT SPEED SENSOR RH

HINT:
Perform the same procedure as for the LH side.



31. INSTALL FRONT AXLE SHAFT NUT LH
  1. Clean the threaded parts on the drive shaft and a new axle shaft nut using a non-residue solvent.

    HINT:
    1. Be sure to perform this work even when using a new drive shaft.
    2. Keep the threaded parts free of oil and foreign matter.



    C210914
  1. Using a socket wrench (30 mm), install the axle shaft nut.

    Torque:
    216 N*m{ 2203 kgf*cm , 159 ft.*lbf }

  1. Using a chisel and hammer, stake the front axle shaft nut.



32. INSTALL FRONT AXLE SHAFT NUT RH

HINT:
Perform the same procedure as for the LH side.



33. INSTALL FRONT EXHAUST PIPE ASSEMBLY (w/ Exhaust Heat Recirculation System)

NOTICE:
When installing the water hose, ensure that the exhaust heat recirculation system is filled with coolant. Otherwise, the engine water pump assembly may be damaged.



    A077857
  1. Using a vernier caliper, measure the free length of the compression springs.
    Minimum
    41.5 mm (1.63 in.)

    HINT:
    If the free length is less than minimum, replace the compression spring.

  1. Temporarily install a new gasket to the exhaust manifold.



    A181728E38
  1. Using a plastic hammer and wooden block, tap in the gasket until its surface is flush with the exhaust manifold.
    Text in Illustration 
    *1
    Exhaust Manifold
    *2
    Gasket
    *a
    Wooden Block

    NOTICE:
    1. Be careful with the installation direction of the gasket.
    2. Do not reuse the gasket.
    3. Do not damage the gasket.
    4. Do not push in the gasket by using the exhaust pipe when connecting it.

  1. Connect the front exhaust pipe assembly to the 3 exhaust pipe supports.



    A212645
  1. Install the front exhaust pipe assembly with the 2 bolts and 2 compression springs.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



    A212644
  1. Connect the 2 heater water hoses.



34. INSTALL FRONT EXHAUST PIPE ASSEMBLY (w/o Exhaust Heat Recirculation System)


    A077857
  1. Using a vernier caliper, measure the free length of the compression springs.
    Minimum
    41.5 mm (1.63 in.)

    HINT:
    If the free length is less than minimum, replace the compression spring.

  1. Temporarily install a new gasket to the exhaust manifold.



    A181728E38
  1. Using a plastic hammer and wooden block, tap in the gasket until its surface is flush with the exhaust manifold.
    Text in Illustration 
    *1
    Exhaust Manifold
    *2
    Gasket
    *a
    Wooden Block

    NOTICE:
    1. Be careful with the installation direction of the gasket.
    2. Do not reuse the gasket.
    3. Do not damage the gasket.
    4. Do not push in the gasket by using the exhaust pipe when connecting it.

  1. Connect the front exhaust pipe assembly to the 3 exhaust pipe supports.



    A212645
  1. Install the front exhaust pipe assembly with the 2 bolts and 2 compression springs.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



35. INSTALL FRONT CENTER FLOOR BRACE


    A264084
  1. Install the front center floor brace with the 4 bolts.

    Torque:
    51 N*m{ 520 kgf*cm , 38 ft.*lbf }



36. INSTALL FRONT NO. 3 ENGINE UNDER COVER


    A212642
  1. Install the front No. 3 engine under cover with the 4 clips.



37. INSTALL TAIL EXHAUST PIPE ASSEMBLY


    A077857
  1. Using a vernier caliper, measure the free length of the compression springs.
    Minimum
    38.5 mm (1.52 in.)

    HINT:
    If the free length is less than minimum, replace the compression spring.

  1. Temporarily install a new gasket to the front exhaust pipe assembly.



    A181728E38
  1. Using a plastic hammer and wooden block, tap in the gasket until its surface is flush with the front exhaust pipe assembly.
    Text in Illustration 
    *1
    Front Exhaust Pipe Assembly
    *2
    Gasket
    *a
    Wooden Block

    NOTICE:
    1. Be careful with the installation direction of the gasket.
    2. Do not reuse the gasket.
    3. Do not damage the gasket.
    4. Do not push in the gasket by using the exhaust pipe when connecting it.

  1. Connect the tail exhaust pipe assembly to the 2 exhaust pipe supports.



    A212641
  1. Install the tail exhaust pipe assembly with the 2 bolts and 2 compression springs.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



38. INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY


    C208472
  1. Align the round hole in the No. 1 steering column hole cover sub-assembly with the protrusion of the steering link assembly to install the cover.



39. CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY


    C206262E01
  1. Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering intermediate shaft to connect the No. 2 steering intermediate shaft assembly to the steering intermediate shaft.
    Text in Illustration 
    *1
    Matchmark

  1. Install the bolt.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }



40. INSTALL COLUMN HOLE COVER SILENCER SHEET


    C206261
  1. Install the column hole cover silencer sheet with the 2 clips.

  1. Install the floor carpet.



41. INSTALL WIRE HARNESS


    A213040
  1. Connect the wire harness with the 2 clamps.



    A213039
  1. Install the earth wire with the bolt.

    Torque:
    8.4 N*m{ 85 kgf*cm , 74 in.*lbf }



    A213038
  1. Connect the wire harness with the 3 clamps.



    A269918
  1. Connect the wire harness to the engine room junction block.

  1. Connect the 2 connectors and 2 clamps to the engine room junction block.



    A218642
  1. Connect the connector to the ECM with the lock lever.

  1. Connect the 2 clamps.



42. INSTALL COMPRESSOR WITH MOTOR ASSEMBLY


  1. for Type A:

    1. Temporarily install the compressor with motor assembly with the 3 bolts.



    2. E247340E01
    3. Install the compressor with motor assembly with the 3 bolts.

      Torque:
      25 N*m{ 250 kgf*cm , 18 ft.*lbf }

      NOTICE:
      Tighten the bolts in the order shown in the illustration to install the compressor with motor assembly.



    4. E247341E01
    5. Connect the connector <B>.
      Text in Illustration 
      *1
      Green-colored Lock

    6. Connect the connector <A> and lock the green-colored lock as shown in the illustration.

      CAUTION:
      Make sure to wear insulating gloves.

      NOTICE:
      Make sure that the connector is connected securely.



  1. for Type B:

    1. Temporarily install the compressor with motor assembly with the 3 bolts.



    2. E189090E02
    3. Install the compressor with motor assembly with the 3 bolts.

      Torque:
      25 N*m{ 250 kgf*cm , 18 ft.*lbf }

      NOTICE:
      Tighten the bolts in the order shown in the illustration to install the compressor with motor assembly.



    4. E245114E01
    5. Connect the connector <B>.
      Text in Illustration 
      *1
      Green-colored Lock

    6. Connect the connector <A> and lock the green-colored lock as shown in the illustration.

      CAUTION:
      Make sure to wear insulating gloves.

      NOTICE:
      Make sure that the connector is connected securely.



43. CONNECT FUEL TUBE SUB-ASSEMBLY
  1. Connect the fuel tube connector and fuel pipe.

    NOTICE:
    Align the fuel tube connector with the pipe, then push the fuel tube connector in until the retainer makes a "click" sound. If the connection is tight, apply a small amount of engine oil to the tip of the pipe. After connecting, pull the pipe and connector to make sure that they are securely connected.



    A213034
  1. Engage the claw and install the No. 1 fuel pipe clamp.



44. CONNECT NO. 1 FUEL VAPOR FEED HOSE


    A213033
  1. Connect the No. 1 fuel vapor feed hose with the clamp.



45. CONNECT HEATER HOSE


    A218276
  1. Connect the heater hose with the clamp.



46. CONNECT INLET HEATER WATER HOSE


    A213031
  1. Connect the inlet heater water hose with the clamp.



47. CONNECT OUTLET HEATER WATER HOSE


    A213030
  1. Connect the outlet heater water hose with the clamp.



48. CONNECT NO. 5 INVERTER COOLING HOSE


    A215989
  1. Connect the No. 5 inverter cooling hose with the clamp.



49. CONNECT NO. 3 INVERTER COOLING HOSE


    A215988
  1. Connect the No. 3 inverter cooling hose with the clamp.



50. CONNECT NO. 4 WATER BY-PASS HOSE


    A213028
  1. Connect the No. 4 water by-pass hose with the clamp.



51. CONNECT NO. 2 RADIATOR HOSE


    A213027
  1. Connect the No. 2 radiator hose with the clamp.



52. CONNECT NO. 1 RADIATOR HOSE


    A213026
  1. Connect the No. 1 radiator hose with the clamp.



53. INSTALL INVERTER TRAY BRACKET


    A213025E01
  1. Position the inverter tray bracket as shown in the illustration.

  1. Temporarily install the inverter tray bracket with bolt B.

  1. Tighten the 5 bolts to the inverter tray bracket in the order the bolt A, bolt C, bolt D, bolt E and bolt B.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Connect the 2 clamps to the inverter tray bracket.



54. INSTALL INVERTER RESERVE TANK ASSEMBLY


    A213024E01
  1. Temporarily install the inverter reserve tank assembly with bolt A.

  1. Tighten the 2 bolts to the inverter reserve tank assembly in the order the bolt B and bolt A.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



55. INSTALL INVERTER WITH CONVERTER ASSEMBLY

CAUTION:
Wear insulating gloves.



    A214665E02
  1. Temporarily install the inverter with converter assembly with the 3 bolts.

    NOTICE:
    1. Since the inverter with converter assembly is very heavy, 2 people are needed to install the inverter with converter assembly. When installing the inverter with converter assembly, do not damage the parts around it.
    2. To prevent damage, do not hold the inverter with converter assembly by the connectors.
    3. To prevent damage due to static electricity, do not touch the terminals of the disconnected connectors.

  1. Tighten the bolt A.

    Torque:
    12 N*m{ 122 kgf*cm , 8 ft.*lbf }

  1. Tighten the 2 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 8 ft.*lbf }



56. CONNECT WATER HOSE


    A214662
  1. Connect the water hose to the inverter with converter assembly and lock the hose with the retainer.

    NOTICE:
    1. Insert the retainer until a click sound is heard.
    2. Pull on the hose to confirm that the hose is securely connected.
    3. If there is foreign matter on the union or the O-ring, clean it with water and finger scouring.



    A214664
  1. Connect the water hose to the inverter with converter assembly and lock the hose with the retainer.

    NOTICE:
    1. Insert the retainer until a click sound is heard.
    2. Pull on the hose to confirm that the hose is securely connected.
    3. If there is foreign matter on the union or the O-ring, clean it with water and finger scouring.



57. CONNECT NO. 2 ENGINE ROOM WIRE


    A214660
  1. Disconnect the No. 2 engine room wire from the protector.



    A214659
  1. Connect the No. 2 engine room wire with the bolt and 2 claws.

    Torque:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

    NOTICE:
    Pass the No. 2 engine room wire under the two cooling hoses that pass beside the inverter.



    A214658
  1. Install the No. 1 relay block cover and 2 clamps.

  1. Install the relay block cover.



58. REMOVE INVERTER TERMINAL COVER

CAUTION:
Wear insulating gloves.



    A209686
  1. Remove the 9 bolts and inverter terminal cover.

    NOTICE:
    Make sure to pull the inverter terminal cover straight up, as a connector is connected to the bottom of the cover.



59. CONNECT NO. 2 ENGINE WIRE

CAUTION:
Wear insulating gloves.

NOTICE:
Do not allow any foreign matter or water to enter the inverter with converter assembly.



    A248444E01
  1. Temporarily install the No. 2 engine wire (high voltage cables of the air conditioning) and 4 bolts to the inverter assembly by hand.

  1. Fully tighten the 4 bolts.

    Torque:
    Bolt A:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
    Bolt B:
    9.2 N*m{ 94 kgf*cm , 81 in.*lbf }

    NOTICE:
    Be sure to use a torque wrench to tighten the bolts.



    A214657
  1. Connect the harness clamp.



60. CONNECT HIGH VOLTAGE CABLE OF FRONT TRANSAXLE

CAUTION:
Wear insulating gloves.

NOTICE:
Do not allow any foreign matter or water to enter the inverter with converter assembly.



    A248443E01
  1. Temporarily install the high voltage cable of the motor (MG2) and 5 bolts to the inverter assembly by hand.

  1. Fully tighten the 5 bolts.

    Torque:
    Bolt A:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
    Bolt B:
    9.2 N*m{ 94 kgf*cm , 81 in.*lbf }

    NOTICE:
    Be sure to use a torque wrench to tighten the bolts.



    A214656
  1. Connect the harness clamp.



    A248442E01
  1. Temporarily install the high voltage cable of the generator (MG1) and 5 bolts to the inverter assembly by hand.

  1. Fully tighten the 5 bolts.

    Torque:
    Bolt A:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
    Bolt B:
    9.2 N*m{ 94 kgf*cm , 81 in.*lbf }

    NOTICE:
    Be sure to use a torque wrench to tighten the bolts.



    A215780E01
  1. Install the cable and cover.
    Text in Illustration 
    *1
    Align Mark

    NOTICE:
    Close the cover so that the matchmarks are not visible.



61. CONNECT FRAME WIRE

CAUTION:
Wear insulating gloves.

NOTICE:
  1. Make sure that the interlock is fully engaged.
  2. Do not allow any foreign matter or water to enter the inverter with converter assembly.



    A231539E01
  1. Temporarily install the frame wire (high voltage cables of the hybrid battery) and 4 bolts to the inverter assembly by hand.
    Text in Illustration 
    *1
    Front view of frame wire connector
    *2
    Interlock
    *3
    High voltage cables of the hybrid battery

  1. Fully tighten the 4 bolts.

    Torque:
    Bolt A:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
    Bolt B:
    9.2 N*m{ 94 kgf*cm , 81 in.*lbf }

    NOTICE:
    1. Be sure to use a torque wrench to tighten the bolts.
    2. Make sure that the interlock is fully engaged.



    A214649
  1. Connect the harness clamp.



62. CHECK HIGH VOLTAGE CABLE CONNECTION

CAUTION:
Wear insulating gloves.

NOTICE:
Do not allow any foreign matter or water to enter the inverter with converter assembly.



    A248462
  1. Check that each connector and terminal is firmly installed.

    NOTICE:
    Make sure that the bolts are fully tightened.



63. INSTALL INVERTER TERMINAL COVER

CAUTION:
Wear insulating gloves.

NOTICE:
  1. Make sure that the interlock is fully engaged.
  2. Do not allow any foreign matter or water to enter the inverter with converter assembly.



    A231540E01
  1. Install the inverter terminal cover with the 9 bolts to the inverter with converter assembly.
    Text in Illustration 
    *1
    Interlock

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }



64. CONNECT ENGINE ROOM MAIN WIRE

NOTICE:
  1. Make sure that the connectors are fully engaged.
  2. Do not allow any foreign matter or water to enter the inverter with converter assembly.



    A214644
  1. Install the bolt, clamp and clip, and connect the engine room main wire.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



    A214643
  1. Install the bolt.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



    A214645
  1. Connect the engine wire to the engine room main wire.



    A214648
  1. Connect the connector to the inverter with converter assembly and lock the connector with the lock lever.



65. INSTALL NO. 1 INVERTER BRACKET


    A209685E01
  1. Temporarily install the No. 1 inverter bracket with the 3 bolts.

  1. Tighten the 3 bolts in the order shown in the illustration.

    Torque:
    14 N*m{ 140 kgf*cm , 10 ft.*lbf }



66. INSTALL AIR CLEANER HOSE ASSEMBLY


    A212315
  1. Install the air cleaner hose assembly and tighten the hose clamp.

  1. Connect the ventilation hose to the cylinder head cover sub-assembly.



67. INSTALL AIR CLEANER CASE


    A213023
  1. Install the air cleaner case with the 3 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the No. 4 water by-pass hose to the air cleaner case with the 3 clamps.

  1. Install the air cleaner filter element.



68. INSTALL INLET AIR CLEANER ASSEMBLY


    A269507
  1. Install the inlet air cleaner assembly with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



69. INSTALL AIR CLEANER CAP SUB-ASSEMBLY


    A276395
  1. Install the air cleaner cap sub-assembly with the 2 clamps and hose band.

  1. Connect the air flow meter connector.



70. INSTALL SERVICE PLUG GRIP

CAUTION:
Wear insulating gloves.

NOTICE:
Before connecting the service plug, check that no parts and tools remain and that the high voltage terminals and connectors are connected securely.



  1. Wear insulated gloves and install the service plug grip in the order shown in the illustration.


    A249878

  1. Rotate the handle of the service plug grip 90° toward the battery and slide it in the direction shown by the arrow until a click sound is heard.



71. CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL


72. INSTALL REAR NO. 3 FLOOR BOARD


    B227791
  1. Engage the 2 guides to install the rear No. 3 floor board.



73. INSTALL REAR DECK FLOOR BOX
  1. Install the rear deck floor box.



74. INSTALL REAR NO. 2 FLOOR BOARD (for Separate Type)


    B227788E01
  1. Engage the 3 guides <A>.

  1. Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.



75. ADD HYBRID TRANSAXLE FLUID


    C233704E01
  1. Add transaxle fluid until the fluid level is between 0 to 10 mm (0 to 0.394 in.) from the bottom lip of the filler plug opening.
    Text in Illustration 
    *1
    Filler Plug
    *2
    Filler Nozzle

    NOTICE:
    1. Stop the vehicle on a level surface.
    2. Use Toyota Genuine ATF WS.
    3. Be sure to fully insert the filler nozzle into the filler plug opening.
    4. Be sure to add fluid slowly. If fluid is added quickly, the fluid may hit internal parts and bounce back, resulting in fluid coming out of the filler plug opening.
    5. Be sure to directly check that the transaxle fluid level is within the specified range.
    6. Insufficient or excessive amounts of transaxle fluid may damage the hybrid transaxle.

    Reference:
    3.4 liters (3.6 US qts, 3.0 lmp.qts)

  1. After adding fluid, leave it for 30 seconds so that the fluid surface can become still again, and then check that the fluid level is between 0 to 10 mm (0 to 0.394 in.) from the bottom lip of the filler plug opening. (If the fluid is insufficient, return to the Add Hybrid Transaxle Fluid procedure.)

  1. Using a 10 mm hexagon socket wrench, install the filler plug with a new gasket.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }



76. INSPECT HYBRID TRANSAXLE FLUID


    C209290E01
  1. Using a 10 mm hexagon socket wrench, remove the filler plug and gasket.
    Text in Illustration 
    *1
    Filler Plug

  1. Check that the fluid level is between 0 to 10 mm (0 to 0.394 in.) from the bottom lip of the filler plug opening. (If the fluid is insufficient, return to the Add Hybrid Transaxle Fluid procedure.)

    NOTICE:
    1. Stop the vehicle on a level surface.
    2. Be sure to directly check that the transaxle fluid level is within the specified range.
    3. Insufficient or excessive amounts of transaxle fluid may damage the hybrid transaxle.
    4. Recheck the transaxle fluid level after driving following fluid replacement.

  1. Check for leaks if the quantity of transaxle fluid is low.

  1. Using a 10 mm hexagon socket wrench, install the filler plug with a new gasket.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }



77. ADD COOLANT (for Engine)
  1. Tighten the radiator drain cock plug.

  1. Remove the reservoir tank cap.



    A213418E01
  1. Add coolant to B line of the reservoir tank.
    Text in Illustration 
    *1
    B Line

    Standard Capacity:
    Item
    Capacity
    Engine coolant
    w/ Exhaust Heat Recirculation System:
    7.2 liters (7.6 US qts, 6.3 lmp. qts)
    w/o Exhaust Heat Recirculation System:
    6.5 liters (6.8 US qts, 5.7 lmp. qts)

    HINT:
    TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Squeeze the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level is low, add coolant.

  1. Install the reservoir tank cap.

  1. Put the engine in inspection mode (Click here).

  1. Bleed air from the cooling system.

    NOTICE:
    1. Before starting the engine, turn the A/C switch off.
    2. Adjust the heater control to the maximum hot setting.
    3. Adjust the blower speed to low setting.


    1. Warm up the engine until the thermostat opens. While the thermostat is open, allow the coolant to circulate for several minutes.

      HINT:
      The thermostat opening timing can be confirmed by squeezing the inlet radiator hose by hand, and sensing vibrations when the engine coolant starts to flow inside the hose.

      CAUTION:
      When squeezing the radiator hose:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the radiator fan.

    2. Squeeze the inlet and outlet radiator hoses several times by hand to bleed air from the system.

      CAUTION:
      When squeezing the radiator hose:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the radiator fan.



    A213418E02
  1. After the engine has cooled down, check that the coolant level is between full and low.
    Text in Illustration 
    *1
    Full Line
    *2
    Low Line
    If the coolant level is low, add coolant to the full line on the reservoir tank.



78. ADD COOLANT (for Inverter)

NOTICE:
  1. Do not reuse the drained coolant because it may contain foreign matter.
  2. If the vehicle is driven with air in the inverter cooling system, damage may occur and the following DTCs may be set.

    DTC Code
    Detection Item
    P0A01-726
    Motor Electronics Coolant Temperature Sensor Circuit Range / Performance
    P0A04-725
    Motor Electronics Coolant Temperature Sensor Circuit Intermittent
    P0A08-264
    DC / DC Converter Status Circuit
    P0A78-284
    Drive Motor "A" Inverter Performance
    P0A78-286
    Drive Motor "A" Inverter Performance
    P0A7A-322
    Generator Inverter Performance
    P0A7A-324
    Generator Inverter Performance
    P0A93-346
    Inverter Cooling System Performance
    P0A94-553
    DC / DC Converter Performance
    P0A94-557
    DC / DC Converter Performance
    P0AEE-277
    Motor Inverter Temperature Sensor "A" Circuit Range / Performance
    P0AF1-276
    Drive Motor Inverter Temperature Sensor "A" Circuit Intermittent / Erratic
    P0BCD-315
    Generator Inverter Temperature Sensor Circuit Range / Performance
    P0BD0-314
    Generator Inverter Temperature Sensor Circuit Intermittent / Erratic
    P0C39-626
    DC / DC Converter Temperature Sensor "A" Range / Performance
    P0C3C-625
    DC / DC Converter Temperature Sensor "A" Intermittent / Erratic
    P0C3E-628
    DC / DC Converter Temperature Sensor "B" Range / Performance
    P0C41-627
    DC / DC Converter Temperature Sensor "B" Intermittent / Erratic
    P0C73-776
    Motor Electronics Coolant Pump "A" Control Performance



    A214673
  1. Slowly pour coolant into the reserve tank until it reaches the F line.

    Coolant quantity:
    2.1 liters (2.2 US qts, 1.8 Imp. qts.)

  1. When using the Techstream:

    1. Connect the Techstream to the DLC3.

    2. Turn the power switch on (IG).

    3. On the Techstream, enter the following menus: Powertrain / Hybrid Control / Active Test / Activate the Water Pump.

    4. Keep the coolant at the F line in the reserve tank to compensate for the drop in coolant level when the air bleeds.

      Standard:
      Air bleeding from the inverter cooling system is completed when the noise made by the water pump becomes smaller and the circulation of coolant in the reserve tank improves.

      HINT:
      Loud noise made by the water pump and poor circulation of coolant in the reserve tank indicates that there is air in the cooling system.

  1. When not using the Techstream:

    1. Turn the power switch on (READY). [*1]

    2. Turn the power switch off and add coolant to the F line because the coolant level drops as the air bleeds. [*2]

      NOTICE:
      1. Be sure to turn the power switch off before adding SLLC.
      2. Do not work on the components in the engine compartment while the vehicle is in the READY-on state because the engine is in intermittent operation.

    3. Repeat steps [*1] and [*2] until air bleeding from the cooling system is completed.

      Standard:
      Air bleeding from the inverter cooling system is completed when the noise made by the water pump becomes smaller and the circulation of coolant in the reserve tank improves.

      HINT:
      Loud noise made by the water pump and poor circulation of coolant in the reserve tank indicates that there is air in the cooling system.

  1. After the air is completely bled from the cooling system, tighten the reserve tank cap.



    A214673
  1. Add coolant to the F line of the reserve tank.



79. ADD ENGINE OIL
  1. Add new engine oil and install the oil filler cap.

    Standard Oil Grade 
    Oil Grade
    Oil Viscosity (SAE)
    1. ILSAC multigrade engine oil
    0W-20

    Standard Capacity 
    Item
    Standard Condition
    Drain and refill with oil filter change
    4.2 liters (4.4 US qts, 3.7 lmp. qts)
    Drain and refill without oil filter change
    3.9 liters (4.1 US qts, 3.4 lmp. qts)
    Dry fill
    4.7 liters (5.0 US qts, 4.1 lmp. qts)



80. INSPECT ENGINE OIL LEVEL
  1. Put the engine in inspection mode (Click here).

  1. Warm up and stop the engine, then wait for 5 minutes. The oil level should be between the low level and full level marks on the engine oil level dipstick. If the engine oil level is low, check for leakage and add oil up to the full level mark.

    NOTICE:
    Do not fill with engine oil to above the full level mark.

    HINT:
    A certain amount of engine oil will be consumed while driving. In the following situations, oil consumption may increase, and engine oil may need to be refilled in between oil maintenance intervals.
    1. When the engine is new, for example directly after purchasing the vehicle or after replacing the engine.
    2. If low quality oil or oil of an inappropriate viscosity is used.
    3. When driving at high engine speed or with a heavy load, (when towing , or), when driving while accelerating or decelerating frequently.
    4. When leaving the idling for a long time, or when driving frequently through heavy traffic.
    When judging the amount of oil consumption, keep in mind that the oil may have become diluted, making it difficult to judge the true level accurately.



81. INSPECT FOR FUEL LEAK
  1. Check fuel pump operation.

    1. Connect the Techstream to the DLC3.

    2. Turn the power switch on (IG).

      NOTICE:
      Do not start the engine.

    3. Turn the Techstream on.

    4. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

    5. Check for pressure in the fuel inlet tube from the fuel line. Check that sounds of fuel flowing from the fuel tank can be heard. If no sounds can be heard, check the integration relay, fuel pump, ECM and wiring connectors.

  1. Inspect for fuel leaks.

    1. Check that there is no fuel leakage after performing maintenance anywhere on the fuel system. If there is a fuel leak, repair or replace parts as necessary.

  1. Turn the power switch off.

  1. Disconnect the Techstream from the DLC3.



82. INSPECT FOR COOLANT LEAK (for Engine)

CAUTION:
Do not remove the reservoir tank cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

NOTICE:
Before performing each inspection, turn the A/C switch off.

  1. Remove the reservoir tank cap.



    A213419
  1. Fill the radiator and reservoir with coolant, and then attach a radiator cap tester.

  1. Put the engine in inspection mode (Click here).

  1. Warm up the engine.

  1. Using the reservoir cap tester, increase the pressure inside the radiator to 108 kPa (1.1 kgf/cm2, 16 psi), and check that the pressure does not drop. If the pressure drops, check the hoses, radiator, front exhaust pipe assembly and the heater hose around and engine water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.

  1. Remove the radiator cap tester.

  1. Install the reservoir tank cap.



83. INSPECT FOR COOLANT LEAK (for Inverter)
  1. Remove the reserve tank cap.

    CAUTION:
    To avoid the danger of being burned, do not remove the reserve tank cap while the coolant for the inverter is still hot.



    A214668
  1. Install the radiator cap tester.

  1. Pump the radiator cap tester to 122 kPa (1.2 kgf/ cm2, 17.7 psi), and then check that the pressure does not drop.

    HINT:
    If the pressure drops, check the hoses, radiator, water pump, inverter with converter, and hybrid vehicle transaxle assembly for leaks.

  1. Reinstall the reserve tank cap.



84. INSPECT FOR OIL LEAK


85. INSPECT FOR EXHAUST GAS LEAK


86. INSTALL NO. 2 ENGINE UNDER COVER


87. INSTALL NO. 1 ENGINE UNDER COVER


88. INSTALL FRONT BUMPER LOWER ABSORBER (w/ Cover)


89. INSTALL FRONT SPOILER COVER (w/ Front Spoiler)


90. INSTALL REAR ENGINE UNDER COVER LH


91. INSTALL REAR ENGINE UNDER COVER RH


92. INSTALL FRONT WHEELS

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



93. INSPECT IGNITION TIMING
  1. Put the engine in inspection mode (Click here).

  1. Warm up and stop the engine.

  1. When using the Techstream:
    Check the ignition timing.

    1. Connect the Techstream to the DLC3.

    2. Put the engine in inspection mode (Click here).

    3. Turn the Techstream on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / IGN Advance.

      Standard ignition timing:
      0 to 16 degrees BTDC

      NOTICE:
      1. Check the ignition timing with the cooling fans off.
      2. Turn off all electrical systems and the A/ C.
      3. When checking the ignition timing, the shift lever should be in P.

      HINT:
      Refer to the Techstream operator's manual for further details.

    5. Check that the ignition timing advances immediately when the engine speed is increased.

    6. Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1 / ON.

    7. Monitor IGN Advance of the Data List.

      Standard ignition timing:
      8 to 12 degrees BTDC

      NOTICE:
      When checking the ignition timing, the shift lever should be in P.

      HINT:
      Refer to the Techstream operator's manual for further details.

    8. Enter the following menus: Connect the TC and TE1 / OFF.

    9. Turn the power switch off.

    10. Turn the Techstream off.

    11. Disconnect the Techstream from the DLC3.



  1. When not using the Techstream:



      A122830E14
    1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

      SST
      09843-18040  

      NOTICE:
      1. Confirm the terminals before connecting them. Connecting the wrong terminals may result in damage to electrical components.
      2. Check the ignition timing with the cooling fans off.
      3. Turn off all electrical systems and the A/ C.
      4. When checking the ignition timing, the shift lever should be in P.

    2. Remove the No. 2 cylinder head cover .



    3. A203506
    4. Pull out the wire harness shown in the illustration.

      NOTICE:
      After checking, wrap the wire harness with tape.

    5. Connect the clip of the timing light to the wire harness.

      NOTICE:
      Use a timing light that detects the primary signal.

    6. Inspect the ignition timing at idle.

      Standard ignition timing:
      8 to 12 degrees BTDC

      NOTICE:
      When checking the ignition timing, the shift lever should be in P.

      HINT:
      After running the engine at 1000 to 1300 rpm for 5 seconds, check that it returns to idle speed.

    7. Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.

    8. Inspect the ignition timing at idle.

      Standard ignition timing:
      0 to 16 degrees BTDC

    9. Confirm that the ignition timing advances when the engine rpm is increased.

    10. Remove the timing light.

    11. Install the No. 2 cylinder head cover .



94. INSPECT ENGINE IDLE SPEED
  1. Put the engine in inspection mode (Click here).

  1. Warm up and stop the engine.

  1. Connect the Techstream to the DLC3.

  1. Put the engine in inspection mode (Click here).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

    HINT:
    Refer to the Techstream operator's manual for further details.

  1. Inspect the engine idle speed.

    Standard idle speed:
    950 to 1050 rpm

    NOTICE:
    1. Turn all electrical systems and the A/C off.
    2. Inspect the idle speed with the cooling fans off.
    3. When checking the ignition timing, the shift lever should be in P.

  1. Turn the power switch off.

  1. Turn the Techstream off.

  1. Disconnect the Techstream from the DLC3.



95. INSPECT CO/HC

HINT:
This check determines whether or not the idle CO / HC complies with regulations.

  1. Put the engine in inspection mode (Click here).

  1. Warm up the engine.

  1. Run the engine at 2500 rpm for approximately 180 seconds.

  1. Insert a CO/HC meter testing probe at least 40 cm (1.3 ft.) into the tailpipe while idling.

  1. Check the CO/HC concentration while idling and when the engine is running at 2500 rpm.

    HINT:
    When doing a 2 mode (with the engine idling/ running at 2500 rpm) test, the measurement procedures are determined by applicable local regulations.
    If the CO/HC concentration does not comply with the regulations, troubleshoot in the order given below.


    1. Check the DTCs (Click here).

    2. See the table below for possible causes, then inspect the applicable parts and repair them if necessary.

      CO
      HC
      Problem
      Possible Cause
      Normal
      High
      Rough idle
      1. Faulty ignition:
        1. Incorrect timing
        2. Fouled, shorted or improperly gapped plugs
      2. Incorrect valve clearance
      3. Leaks from intake and exhaust valves
      4. Leaks from cylinders
      5. Faulty EGR
      Low
      High
      Rough idle (Fluctuating HC reading)
      1. Vacuum leaks:
        1. PCV hoses
        2. Intake manifold
        3. Throttle body
        4. Brake booster line
      2. Lean mixture causing misfire
      3. Faulty EGR
      High
      High
      Rough idle (Black smoke from exhaust)
      1. Restricted air cleaner filter element
      2. Plugged PCV valve
      3. Faulty EFI systems:
        1. Faulty pressure regulator
        2. Faulty engine coolant temperature sensor
        3. Faulty mass air flow meter
        4. Faulty ECM
        5. Faulty injectors
        6. Throttle body
      4. Faulty EGR



96. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

HINT:
Click here.



97. INSTALL NO. 2 CYLINDER HEAD COVER


    A213020
  1. Engage the 3 clips to install the cover.

    NOTICE:
    1. Be sure to engage the clips securely.
    2. Do not apply excessive force or hit the cover to engage the clips. This may cause the cover to break.



98. INSTALL RADIATOR SUPPORT OPENING COVER
  1. Engage the 2 claws and install the radiator support opening cover.

  1. Install the 3 clips.



99. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY


    C205669
  1. Install the outer cowl top panel sub-assembly with the 9 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



    C205673
  1. Bend the water guard plate RH and engage the claw.



    C205671
  1. Bend the No. 1 heater air duct splash shield seal and engage the claw.



    C205668E01
  1. Engage the 2 clamps and guide to install the wire harness.
    Text in Illustration 
    *1
    Clamp
    *2
    Guide



100. INSTALL COWL BODY MOUNTING REINFORCEMENT LH


    C205667
  1. Install the cowl body mounting reinforcement LH with the 3 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



101. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


    E190084E01
  1. Engage the grommet as shown in the illustration.
    Text in Illustration 
    *1
    Grommet

  1. Install the windshield wiper motor and link assembly with the 4 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    NOTICE:
    Be careful not to damage the windshield when installing the windshield wiper motor and link assembly.



    E187024
  1. Engage the 2 clamps.

  1. Connect the connector.



102. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


  1. Engage the 8 guides <B>.


    E187023E01

  1. Engage the 5 claws and 3 guides <A> to install the cowl top ventilator louver sub-assembly as shown in the illustration.



    E187021
  1. Install the 2 clips.



103. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY LH


    E193125E01
  1. Engage the guide <B> as shown in the illustration.

  1. Engage the claw and guide <A> to install the cowl side ventilator sub-assembly LH as shown in the illustration.



104. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and LH side.



105. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.



    E112237E06
  1. When reusing the front wiper arm and blade assembly RH:

    1. Clean the wiper arm serrations.
      Text in Illustration 
      *1
      Wiper Arm Serration
      *2
      Wire Brush
      *3
      Wiper Pivot Serration

  1. When reusing the windshield wiper link assembly:

    1. Clean the wiper pivot serrations with a wire brush.



    E189305E01
  1. Install the front wiper arm and blade assembly RH with the 2 nuts to the position shown in the illustration.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }

    Text in Illustration 
    *1
    Ceramic Dot

    HINT:
    Hold the wiper arm by hand while tightening the nut.



106. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E112237E05
  1. When reusing the front wiper arm and blade assembly LH:

    1. Clean the wiper arm serrations.
      Text in Illustration 
      *1
      Wiper Arm Serration
      *2
      Wire Brush
      *3
      Wiper Pivot Serration

  1. When reusing the windshield wiper link assembly:

    1. Clean the wiper pivot serrations with a wire brush.



    E189304E01
  1. Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }

    Text in Illustration 
    *1
    Ceramic Dot

    HINT:
    Hold the wiper arm by hand while tightening the nut.

  1. Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.



107. INSTALL FRONT WIPER ARM HEAD CAP


    E187018
  1. Engage the 3 claws to install the front wiper arm head cap.

    HINT:
    Use the same procedure for the RH side and LH side.



108. CHECK ABS SPEED SENSOR SIGNAL

HINT:
Click here.