Home › Suspension › ALIGNMENT / HANDLING DIAGNOSIS › REAR WHEEL ALIGNMENT

REAR WHEEL ALIGNMENT > INSPECTION

for Preparation Click here


NOTICE:
If the wheel alignment has been adjusted, and if suspension or underbody components have been removed/installed or replaced, be sure to perform the following initialization procedure in order for the system to function normally:
  1. Perform zero point calibration of the yaw rate and acceleration sensor and test mode inspection.



1. INSPECT TIRES
Click here.


2. MEASURE VEHICLE HEIGHT


C207236E01

NOTICE:
  1. Before inspecting the wheel alignment, adjust the vehicle height to the specified value.
  2. Be sure to perform measurement on a level surface.
  3. If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.
  4. Inspect while the vehicle is unloaded.

  1. Bounce the vehicle up and down at the corners to stabilize the suspension.

  1. Measure the vehicle height.

    Measurement points:
    1. A: Ground clearance of front No. 1 lower suspension arm bushing set bolt center
    1. B: Ground clearance of rear axle beam bushing set bolt center
    1. C: Ground clearance of front wheel center
    1. D: Ground clearance of rear wheel center

    Vehicle Height (Unloaded Vehicle):

    Tire Size
    Front C - A
    Rear D - B
    195/65R15
    108 mm (4.25 in.)
    90 mm (3.54 in.)*
    26 mm (1.02 in.)
    9 mm (0.354 in.)*
    215/45R17
    103 mm (4.06 in.)
    21 mm (0.827 in.)

    * For vehicle height for Rough Road Package.



3. INSPECT CAMBER

NOTICE:
Inspect while the vehicle is unloaded.

  1. Install a camber-caster-kingpin gauge.

  1. Inspect the camber.

    Camber (Unloaded Vehicle):

    Tire Size
    Camber Inclination
    Right-left Difference
    195/65R15
    -1°29' +/- 30' (-1.48° +/- 0.50°)
    30' (0.50°) or less
    215/45R17
    -1°28' +/- 30' (-1.47° +/- 0.50°)

    HINT:
    Camber is not adjustable. If the measurement is not within the specified range, inspect the suspension parts for damage and/or wear, and replace them if necessary.



4. INSPECT TOE-IN

NOTICE:
Inspect while the vehicle is unloaded.

  1. Bounce the vehicle up and down at the corners to stabilize the suspension.

  1. Release the parking brake and move the shift lever to N.

  1. Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)



    C188968E03
  1. Put tread center marks on the rearmost points of the rear wheels and measure the distance between the marks (dimension B).
    Text in Illustration 
    *1
    Front of the Vehicle
    *2
    Tread Center Mark
    *3
    Dimension B

  1. Slowly push the vehicle straight ahead to cause the rear wheels to rotate 180° using the rear tire valve as a reference point.

    HINT:
    Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from Step A again.



    C188969E03
  1. Measure the distance between the tread center marks on the front side of the wheels (dimension A).
    Text in Illustration 
    *1
    Front of the Vehicle
    *2
    Dimension A

    Toe-in (Unloaded Vehicle):

    Tire Size
    Specified Condition
    Right-left Difference
    195/65R15
    C + D: 0°17' +/- 18' ( 0.29° +/- 0.30°)
    C + D: 0°10' +/- 18' ( 0.17° +/- 0.30°)*
    45' (0.75°) or less
    B - A: 2.9 +/- 3 mm (0.114 +/- 0.118 in.)
    B - A: 1.7 +/- 3 mm (0.0669 +/- 0.118 in.)*
    -
    215/45R17
    C + D: 0°15' +/- 18' ( 0.25° +/- 0.30°)
    45' (0.75°) or less
    B - A: 2.5 +/- 3 mm (0.0984 +/- 0.118 in.)
    -

    * For vehicle height for Rough Road Package.

    HINT:
    Measure "B - A" only when "C + D" cannot be measured.

    If the toe-in is not within the specified range, inspect the suspension parts and replace them if necessary.