POWER WINDOW REGULATOR MOTOR (for Front Door) > REMOVAL |
| 1. REMOVE REAR NO. 2 FLOOR BOARD (for Separate Type) |
![]() |
Disengage the 2 guides <A> as shown in the illustration.
Disengage the 3 guides <B> and remove the rear No. 2 floor board.
| 2. REMOVE REAR DECK FLOOR BOX |
Remove the rear deck floor box.
| 3. REMOVE REAR NO. 3 FLOOR BOARD |
![]() |
Disengage the 2 guides and remove the rear No. 3 floor board.
| 4. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG |
![]() |
Using a moulding remover, disengage the 3 claws and remove the front door inside handle bezel plug.
| 5. REMOVE ASSIST GRIP COVER |
![]() |
Using a moulding remover, disengage the 6 claws, 2 clips and 3 guides, and remove the assist grip cover.
| 6. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side) |
![]() |
Disengage the 7 claws and 3 guides.
Disconnect the connector and remove the power window regulator master switch assembly with front door armrest base panel.
| 7. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side) |
![]() |
Disengage the 7 claws and 3 guides.
Disconnect each connector and remove the power window regulator switch assembly with front door armrest base panel.
| 8. REMOVE DOOR ARMREST COVER |
![]() |
Remove the door armrest cover.
| 9. REMOVE COURTESY LIGHT ASSEMBLY |
![]() |
Using a moulding remover, disengage the claw.
Disconnect the connector and remove the courtesy light assembly.
| 10. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY |
![]() |
Put protective tape around the front door panel.
| *1 | Protective Tape |
![]() |
Remove the 2 screws.
Using a clip remover, disengage the 9 clips.
Pull out the front door trim board sub-assembly in the direction indicated by the arrow in the illustration.
Raise the front door trim board sub-assembly and remove the front door trim board sub-assembly together with the front door inner glass weatherstrip.
![]() |
Disengage the 2 claws and disconnect the front door inside handle sub-assembly.
| 11. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY |
![]() |
Disconnect the front door lock remote control cable and front door inside locking cable, and remove the front door inside handle sub-assembly.
| 12. REMOVE FRONT DOOR TRIM BRACKET |
![]() |
Remove the 2 screws and front door trim bracket.
| 13. REMOVE FRONT DOOR SERVICE HOLE COVER |
![]() |
Remove the front door service hole cover.
| 14. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY |
![]() |
Remove the grommet.
Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.
Disconnect the cable from the negative (-) battery terminal and power window regulator master switch assembly.
![]() |
Remove the 2 bolts.
![]() |
Remove the front door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.
| 15. REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY |
![]() |
Disconnect the connector.
Loosen the temporary bolt.
| *1 | Temporary Bolt |
Remove the 5 bolts.
Remove the front door window regulator assembly.
Remove the temporary bolt from the front door window regulator assembly.
| 16. REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY |
![]() |
Using a T25 "TORX" driver, remove the 3 screws and the front power window regulator motor assembly.