Home › Engine / Hybrid System › 2ZR-FXE COOLING › COOLING FAN SYSTEM

COOLING FAN SYSTEM > Cooling Fan Circuit

for Preparation Click here


DESCRIPTION

The ECM turns on or off the fan relays using signals calculated from the engine coolant temperature, air conditioning switch (on/off), air conditioning refrigerant pressure, engine speed, and vehicle speed signals.
The ECM switches the circuit of the cooling fan motors between series and parallel by turning on or off the fan relays in order to control the speed of the cooling fan motors in two steps.

WIRING DIAGRAM

Refer to System Diagram (Click here).

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE ELECTRIC COOLING FAN)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Electric Cooling Fan.

    OK:
    Tester Operation
    Specified Condition
    ON
    Fans operate
    OFF
    Fans do not operate



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT ECM (FANL AND FANH VOLTAGE)


    A194151E74
  1. Disconnect the ECM connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A57-22 (FANH) - Body ground
    Power switch on (IG)
    11 to 14 V
    A57-21 (FANL) - Body ground
    Power switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the ECM connector.



NG
Go to step 14
OK


3.INSPECT ENGINE ROOM RELAY BLOCK (FAN NO. 1 RELAY AND FAN NO. 3 RELAY VOLTAGE)


    A269779E01
  1. Remove the FAN No. 1 relay and FAN No. 3 relay from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    3 (FAN No. 1 relay) - Body ground
    Always
    11 to 14 V
    5 (FAN No. 3 relay) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *1
    Engine Room Relay Block

  1. Reinstall the FAN No. 1 relay and FAN No. 3 relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ENGINE ROOM RELAY BLOCK)
OK


4.INSPECT FAN NO. 1 RELAY


    B060778E50
  1. Remove the FAN No. 1 relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage is not applied between terminals 1 and 2
    10 kΩ or higher
    Battery voltage is applied between terminals 1 and 2
    Below 1 Ω

  1. Reinstall the FAN No. 1 relay.



NG
REPLACE FAN NO. 1 RELAY
OK


5.INSPECT FAN NO. 2 RELAY


    A159206E01
  1. Remove the FAN No. 2 relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 4
    Battery voltage is not applied between terminals 1 and 2
    Below 1 Ω
    Battery voltage is applied between terminals 1 and 2
    10 kΩ or higher
    3 - 5
    Battery voltage is not applied between terminals 1 and 2
    10 kΩ or higher
    Battery voltage is applied between terminals 1 and 2
    Below 1 Ω

  1. Reinstall the FAN No. 2 relay.



NG
REPLACE FAN NO. 2 RELAY
OK


6.INSPECT FAN NO. 3 RELAY


    B060778E50
  1. Remove the FAN No. 3 relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage is not applied between terminals 1 and 2
    10 kΩ or higher
    Battery voltage is applied between terminals 1 and 2
    Below 1 Ω

  1. Reinstall the FAN No. 3 relay.



NG
REPLACE FAN NO. 3 RELAY
OK


7.CHECK HARNESS AND CONNECTOR (FAN NO. 2 RELAY - BODY GROUND)
  1. Remove the FAN No. 2 relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    5 (FAN No. 2 relay) - Body ground
    Always
    Below 1 Ω

  1. Reinstall the FAN No. 2 relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN NO. 2 RELAY - BODY GROUND)
OK


8.INSPECT COOLING FAN MOTOR


    A215891E06
  1. Disconnect the cooling fan motor connector.

  1. Check that the cooling fan motor operates smoothly when the battery is connected to the cooing fan motor connector.

  1. Measure the current while the motor is operating.

    Standard Current:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    11.2 to 14.5 A

    Text in Illustration 
    *a
    Component without harness connected
    (Cooling Fan Motor)

  1. Reconnect the cooling fan motor connector.



NG
REPLACE COOLING FAN MOTOR (Click here)
OK


9.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - BODY GROUND)


    A217584E02
  1. Disconnect the cooling fan motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    A5-1 - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Cooling Fan Motor)

  1. Reconnect the cooling fan motor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (COOLING FAN MOTOR - BODY GROUND)
OK


10.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - ENGINE ROOM RELAY BLOCK)
  1. Disconnect the cooling fan motor connector.

  1. Remove the FAN No. 1 relay and FAN No. 2 relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    A5-2 - 5 (FAN No. 1 relay)
    Always
    Below 1 Ω
    A5-2 - 4 (FAN No. 2 relay)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):

    Tester Connection
    Condition
    Specified Condition
    A5-2 or 5 (FAN No. 1 relay) - Body ground
    Always
    10 kΩ or higher
    A5-2 or 4 (FAN No. 2 relay) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the cooling fan motor connector.

  1. Reinstall the FAN No. 1 relay and FAN No. 2 relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (COOLING FAN MOTOR - ENGINE ROOM RELAY BLOCK)
OK


11.INSPECT NO. 2 COOLING FAN MOTOR


    A215891E07
  1. Disconnect the No. 2 cooling fan motor connector.

  1. Check that the No. 2 cooling fan motor operates smoothly when the battery is connected to the No. 2 cooling fan motor connector.

  1. Measure the current while the motor is operating.

    Standard Current:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    7.4 to 10.9 A

    Text in Illustration 
    *a
    Component without harness connected
    (No. 2 Cooling Fan Motor)

  1. Reconnect the No. 2 cooling fan fan motor connector.



NG
REPLACE NO. 2 COOLING FAN MOTOR (Click here)
OK


12.CHECK HARNESS AND CONNECTOR (NO. 2 COOLING FAN MOTOR - ENGINE ROOM RELAY BLOCK)
  1. Disconnect the No. 2 cooling fan motor connector.

  1. Remove the FAN No. 2 relay and FAN No. 3 relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    A6-1 - 3 (FAN No. 2 relay)
    Always
    Below 1 Ω
    A6-2 - 3 (FAN No. 3 relay)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):

    Tester Connection
    Condition
    Specified Condition
    A6-1 or 3 (FAN No. 2 relay) - Body ground
    Always
    10 kΩ or higher
    A6-2 or 3 (FAN No. 3 relay) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the No. 2 cooling fan motor connector.

  1. Reinstall the FAN No. 2 relay and FAN No. 3 relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 2 COOLING FAN MOTOR - ENGINE ROOM RELAY BLOCK)
OK


13.INSPECT ENGINE ROOM RELAY BLOCK (FAN NO. 1 RELAY - FAN NO. 2 RELAY)
  1. Remove the FAN No. 1 relay and FAN No. 2 relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    1 (FAN No. 1 relay) - 1 (FAN No. 2 relay)
    Always
    Below 1 Ω
    2 (FAN No. 1 relay) - 2 (FAN No. 2 relay)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):

    Tester Connection
    Condition
    Specified Condition
    1 (FAN No. 1 relay) or 1 (FAN No. 2 relay) - Body ground
    Always
    10 kΩ or higher
    2 (FAN No. 1 relay) or 2 (FAN No. 2 relay) - Body ground
    Always
    10 kΩ or higher

  1. Reinstall the FAN No. 1 relay and FAN No. 2 relay.



NG
REPLACE ENGINE ROOM RELAY BLOCK
OK

REPLACE ECM (Click here)  

14.CHECK FUSE (ECU-IG NO. 1 FUSE VOLTAGE)


    A217203E01
  1. Remove the ECU-IG No. 1 fuse from the instrument panel junction block assembly.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (ECU-IG No. 1 fuse) - Body ground
    Power switch on (IG)
    11 to 14 V

    Text in Illustration 
    *1
    Instrument Panel Junction Block Assembly

  1. Reinstall the ECU-IG No. 1 fuse.



NG
Go to step 20
OK


15.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


  1. Disconnect the instrument panel junction block assembly connector.


    A218060E03

  1. Remove the ECU-IG No. 1 fuse from the instrument panel junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    2C-30 - 2 (ECU-IG No. 1)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):

    Tester Connection
    Condition
    Specified Condition
    2C-30 or 2 (ECU-IG No. 1) - Body ground
    Always
    10 kΩ or higher


    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    -
    -
    *1
    Instrument Panel Junction Block Assembly
    -
    -

  1. Reconnect the ECU-IG No. 1 fuse.

  1. Reconnect the instrument panel junction block assembly connector.



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
OK


16.INSPECT FAN NO. 1 RELAY


    B060778E50
  1. Remove the FAN No. 1 relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage is not applied between terminals 1 and 2
    10 kΩ or higher
    Battery voltage is applied between terminals 1 and 2
    Below 1 Ω

  1. Reinstall the FAN No. 1 relay.



NG
REPLACE FAN NO. 1 RELAY
OK


17.INSPECT FAN NO. 2 RELAY


    A159206E01
  1. Remove the FAN No. 2 relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 4
    Battery voltage is not applied between terminals 1 and 2
    Below 1 Ω
    Battery voltage is applied between terminals 1 and 2
    10 kΩ or higher
    3 - 5
    Battery voltage is not applied between terminals 1 and 2
    10 kΩ or higher
    Battery voltage is applied between terminals 1 and 2
    Below 1 Ω

  1. Reinstall the FAN No. 2 relay.



NG
REPLACE FAN NO. 2 RELAY
OK


18.INSPECT FAN NO. 3 RELAY


    B060778E50
  1. Remove the FAN No. 3 relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage is not applied between terminals 1 and 2
    10 kΩ or higher
    Battery voltage is applied between terminals 1 and 2
    Below 1 Ω

  1. Reinstall the FAN No. 3 relay.



NG
REPLACE FAN NO. 3 RELAY
OK


19.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK - ECM)
  1. Remove the FAN No. 1 relay, FAN No. 2 relay and FAN No. 3 relay from the engine room relay block.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    2 (FAN No. 1 relay) - A57-22 (FANH)
    Always
    Below 1 Ω
    2 (FAN No. 2 relay) - A57-22 (FANH)
    Always
    Below 1 Ω
    2 (FAN No. 3 relay) - A57-21 (FANL)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):

    Tester Connection
    Condition
    Specified Condition
    2 (FAN No. 1 relay) or A57-22 (FANH) - Body ground
    Always
    10 kΩ or higher
    2 (FAN No. 2 relay) or A57-22 (FANH) - Body ground
    Always
    10 kΩ or higher
    2 (FAN No. 3 relay) or A57-21 (FANL) - Body ground
    Always
    10 kΩ or higher

  1. Reinstall the FAN No. 1 relay, FAN No. 2 relay and FAN No. 3 relay.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE ROOM RELAY BLOCK - ECM)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECU-IG NO. 1 FUSE - ENGINE ROOM RELAY BLOCK) 

20.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 1 RELAY)


  1. Disconnect the instrument panel junction block assembly connector.


    A215946E09

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2E-1 - 2C-30
    Battery voltage is not applied between terminals 2B-25 - 2B-6
    10 kΩ or higher
    Battery voltage is applied between terminals 2B-25 - 2B-6
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (to Instrument Panel Junction Block Assembly)

  1. Reconnect the instrument panel junction block assembly connector.



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 1 RELAY)
OK


21.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 1 RELAY VOLTAGE)


    A217589E06
  1. Disconnect the instrument panel junction block assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    2E-1 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *1
    Instrument Panel Junction Block Assembly
    *a
    Front view of wire harness connector
    (to Instrument Panel Junction Block Assembly)

  1. Reconnect the instrument panel junction block assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
OK


22.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)
  1. Disconnect the instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    2B-6 - Body ground
    Always
    Below 1 Ω

  1. Reconnect the instrument panel junction block assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 NO. 1 RELAY - BODY GROUND)
OK


23.CHECK HARNESS AND CONNECTOR (IG1 NO. 1 RELAY - POWER MANAGEMENT CONTROL ECU)
  1. Disconnect the instrument panel junction block assembly connector.

  1. Disconnect the power management control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    L6-2 (IG1D) - 2B-25
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):

    Tester Connection
    Condition
    Specified Condition
    L6-2 (IG1D) or 2B-25 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the instrument panel junction block assembly connector.

  1. Reconnect the power management control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 NO. 1 RELAY - POWER MANAGEMENT CONTROL ECU)
OK

CHECK SMART KEY SYSTEM (Click here)