Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM

DTC    P060B    Internal Control Module A/D Processing Performance

for Preparation Click here


DESCRIPTION

This DTC is stored when a communication error occurs in the ECM.

DTC No.
DTC Detection Condition
Trouble Area
P060B
ECM main CPU communication error
(1 trip detection logic)
  1. ECM
  2. Knock control sensor

MONITOR STRATEGY


Related DTCs
P060B: Internal control module A/D processing performance
Required Sensors/Components (Main)
ECM
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
2 times: Case 1
30 times: Case 2 and 3
MIL Operation
Immediately
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Case 1 and Case 2 
Monitor runs whenever the following DTCs are not stored
None

Case 3 
Monitor runs whenever the following DTCs are not stored
None
Auxiliary battery voltage
8 V or higher

TYPICAL MALFUNCTION THRESHOLDS


Case 1 
AD converter
Fail

Case 2 
Knock control sensor circuit
Fail

Case 3 
Knock control sensor serial communication
Fail

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the power switch on (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the Techstream off.
  5. Turn the power switch off.
  6. Disconnect the Techstream.
  7. Disconnect the cable from the negative (-) auxiliary battery terminal and wait for 1 minute.
  8. Connect the cable to the negative (-) auxiliary battery terminal.
  9. Connect the Techstream to the DLC3.
  10. Turn the power switch on (IG) and turn the Techstream on.
  11. Wait 16 seconds or more.
  12. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  13. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  14. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  15. Input the DTC: P060B.
  16. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  17. If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ OUTPUT DTC (DTC P060B)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the power switch off and turn the Techstream off.

  1. Disconnect the Techstream.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal and wait for 1 minute.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Wait 16 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P060B is output
    B
    DTC P060B and P0327, P0328 are output
    C



B
REPLACE ECM (Click here)

C
GO TO DTC (P0327 AND P0328) (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)