Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

HYBRID CONTROL SYSTEM > Pattern Select Switch EV Mode Circuit

for Preparation Click here


DESCRIPTION

The EV mode signal is sent to the power management control ECU. This signal is then transmitted from the power management control ECU via CAN to the combination meter assembly to illuminate the EV indicator lamp.

WIRING DIAGRAM


C190530E11


INSPECTION PROCEDURE

If any of the following conditions are not met, EV mode may not be turned on or the mode may be canceled. (A buzzer sounds to indicate that the transition to EV mode is canceled and a message is displayed on multi-information display.)

EV Mode Entry Condition
Tester Display
Specified Condition
HV battery charge level
State of Charge
Approximately 50% or higher
Accelerator pedal position
Accelerator Degree
Below approximately 30%
Engine coolant temperature
Engine Coolant Temp
68°F (20°C) or higher
HV battery temperature
Temp of Batt TB1 to TB3
Between 50°F to 104°F (10°C to 40°C)
Vehicle speed
(Varies depending on engine warm-up condition)
-
Cold: 10 mph (16km/h)
Warmed-up: 25 mph (40km/h)
Defroster
-
OFF
Cruise control
-
OFF
Win
Charge Control Value
Below -20000W
Wout
Discharge Control Value
20000W or higher
1.ASK ABOUT VEHICLE CONDITION
  1. Check if a buzzer sounded and a message was displayed on the multi-information display when attempting to enter EV mode.

    Result:
    Result
    Proceed to
    No buzzer sounded and no message was displayed on multi-information display.
    A
    A buzzer sounded and a message was displayed on multi-information display.
    B

HINT:
If a buzzer sounds and a message is displayed on multi-information display, one or more of the EV mode entry conditions have not been met. Check that all of the EV mode entry conditions have been met before pressing the EV drive mode switch.



B
COMPLETED
A


2.READ VALUE USING TECHSTREAM (CAN BUS CHECK)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: System Select / CAN Bus Check.

    Result:
    Result
    Proceed to
    All of the ECUs and sensors that are currently connected to the CAN communication system are displayed.
    A
    None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed.
    B

  1. Turn the power switch off.



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


3.CHECK DTC OUTPUT (HEALTH CHECK)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: System Select / Health Check.

  1. Check DTCs.
    Result 
    Result
    Proceed to
    No DTCs are output.
    A
    DTCs are output.
    B

  1. Turn the power switch off.



B
GO TO DTC CHART
A


4.PERFORM ACTIVE TEST USING TECHSTREAM (INDICAT. EV MODE)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (READY).

  1. Enter the following menus: Body Electrical / Combination Meter / Active Test / Indicat. EV Mode.

  1. Perform the "Indicat. EV Mode" Active Test.

    OK:
    The EV mode indicator light comes on or blinks.

  1. Turn the power switch off.



NG
CHECK METER / GAUGE SYSTEM (Click here)
OK


5.READ VALUE USING TECHSTREAM (EV REQUEST, EV SWITCH)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / EV request, EV Switch.

  1. Read the value displayed on the Techstream.

    Tester Display
    Measurement Item/Range
    Normal Condition
    EV request
    EV mode transition availability/ ON or OFF
    In EV mode: ON
    EV Switch
    EV drive mode switch (Integration control and panel sub-assembly) condition/ ON or OFF
    EV drive mode switch (Integration control and panel sub-assembly) being pushed and held: ON

    Result:

    Result
    Proceed to
    The Techstream display changes according to the EV drive mode switch (Integration control and panel sub-assembly) operation.
    A
    The Techstream display does not change according to the EV drive mode switch (Integration control and panel sub-assembly) operation.
    B

  1. Turn the power switch off.



B
Go to step 6
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

6.INSPECT INTEGRATION CONTROL AND PANEL SUB-ASSEMBLY (EV DRIVE MODE SWITCH)


    C210637E01
  1. Remove the integration control and panel sub-assembly (EV drive mode switch).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L78-3 (S) - L78-5 (E)
    EV drive mode switch (Integration control and panel sub-assembly) being pushed and held
    Below 1 Ω
    EV drive mode switch (Integration control and panel sub-assembly) not pushed
    10 kΩ or higher

Text in Illustration 
*1
Component without harness connected
(EV Drive Mode Switch (Integration Control and Panel Sub-assembly))
  1. Install the integration control and panel sub-assembly.



NG
REPLACE INTEGRATION CONTROL AND PANEL SUB-ASSEMBLY (EV DRIVE MODE SWITCH) (Click here)
OK


7.CHECK HARNESS AND CONNECTOR (EV DRIVE MODE SWITCH - BODY GROUND)
  1. Disconnect connector L78 from the integration control and panel sub-assembly (EV drive mode switch).



    C210638E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L78-5 (E) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*1
Front view of wire harness connector
(to EV Drive Mode Switch (Integration Control and Panel Sub-assembly))
  1. Connect the integration control and panel sub-assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)  

8.CHECK HARNESS AND CONNECTOR (EV DRIVE MODE SWITCH - POWER MANAGEMENT CONTROL ECU)
  1. Disconnect connector L78 from the integration control and panel sub-assembly (EV drive mode switch).

  1. Disconnect connector L5 from the power management control ECU.



    C210648E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L78-3 (S) - L5-13 (EVSW)
    Always
    Below 1 Ω
    L78-3 (S) or L5-13 (EVSW) - Body ground
    Always
    10 kΩ or higher

Text in Illustration 
*1
Front view of wire harness connector
(to EV Drive Mode Switch (Integration Control and Panel Sub-assembly))
*2
Rear view of wire harness connector
(to Power Management Control ECU)
  1. Connect the integration control and panel sub-assembly connector.

  1. Connect the power management control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)