BLACK OUT TAPE (for Rear Door) > INSTALLATION |
| 1. REPAIR INSTRUCTION |
Clean the vehicle body surface.
Using a heat light, heat the vehicle body surface.
| Item | Temperature |
| Vehicle Body | 40 to 60°C (104 to 140°F) |
Wipe off any tape adhesive residue with cleaner.
Installation temperature
When the ambient temperature is below 15°C (59°F), perform the installation procedure after warming the vehicle body surface (installation surface of the door frame) and tape up to between 20 and 30°C (68 and 86°F) using a heat light. When the ambient temperature is above 35°C (95°F), cool the vehicle body surface (installation surface of the door frame) and tape down to between 20 and 30°C (68 and 86°F) prior to installation.
Before installation
Remove any coating roughness or dirt on and around the vehicle body surface where the tape will be installed (installation surface of the door frame). If any roughness or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.
Key points for handling the tape
The tape bends and rolls up easily. Store the tape between flat pieces of cardboard or other similar objects and keep it dry and level.
Key points for installation of the tape (how to use a squeegee and installation procedure for flat surfaces)
To avoid air bubbles, slightly raise the part of the tape that is going to be applied so that its adhesive surface does not touch the vehicle body while applying the tape. Tilt the squeegee at 40 to 50° (pressing forward) or 30 to 45° (pulling) to the vehicle body surface and press the tape onto the vehicle body surface with a force of 20 to 30 N (2 to 3 kgf, 4.5 to 6.7 lbf) at a constant slow speed of 3 to 7 cm (1.18 to 2.76 in.) per second.

Key points for installation of the tape (how to use a squeegee and installation procedure for hemmed surfaces)
![]() |
If it is difficult to apply the tape, install it in several steps as shown in the illustration. Use your fingers or the padded surface of a squeegee to slowly apply the tape to the hem of the vehicle, especially for a small hem.
Key points for installation of the tape (how to use a squeegee and installation procedure for corners)
Remove the release paper and apply the tape carefully with your fingers.
Before applying the tape to each corner, heat the tape using a heat light and gradually apply it, avoiding wrinkles on the tape to achieve a neat finish.
Check after installation
After completing the application, check if the tape is applied neatly. If the tape is not applied neatly, reapply using new tape.
| 2. INSTALL NO. 2 BLACK OUT TAPE |
![]() |
Remove the portion of the No. 2 black out tape at the perforation as shown in the illustration.
Refer to the illustration to position the No. 2 black out tape.

| Dimension | Measurement |
| A | 2 to 4 mm (0.0787 to 0.157 in.) |
| B | 4 to 6 mm (0.157 to 0.236 in.) |
Remove the release paper and apply the tape.
| 3. INSTALL REAR DOOR LOWER OUTSIDE STRIPE |
Refer to the illustration to position the rear door lower outside stripe.

| Dimension | Measurement |
| A | 2.0 mm (0.0787 in.) |
Remove the release paper and apply the stripe.
| 4. INSTALL REAR DOOR UPPER OUTSIDE STRIPE |
Refer to the illustration to position the rear door upper outside stripe.

| Dimension | Measurement |
| A | 2.0 mm (0.0787 in.) |
Remove the release paper and apply the stripe.
| 5. INSTALL REAR DOOR OUTSIDE STRIPE |
Refer to the illustration to position the rear door outside stripe.

| Dimension | Measurement |
| A | 2.0 mm (0.0787 in.) |
Remove the release paper and apply the stripe.
| 6. INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING |
| Item | Temperature |
| Vehicle Body | 40 to 60°C (104 to 140°F) |
| Moulding | 20 to 30°C (68 to 86°F) |
Clean the vehicle body surface.
Using a heat light, heat the vehicle body surface.
Remove the double-sided tape from the vehicle body.
Wipe off any tape adhesive residue with cleaner.
Clean the rear door front window frame moulding (if reusing the rear door front window frame moulding).
Using a heat light, heat the rear door front window frame moulding.
Remove the double-sided tape from the rear door front window frame moulding.
Wipe off any tape adhesive residue with cleaner.
![]() |
Apply new double-sided tape to the rear door front window frame moulding.
| *1 | Double-sided Tape (A) |
| *2 | Double-sided Tape (B) |
| *3 | Double-sided Tape (C) |
| Item | Dimension |
| A | 0.8 mm (0.0315 in.) |
| B | 1.2 mm (0.0472 in.) |
| C | 5.0 mm (0.197 in.) |
| D | 13.0 mm (0.512 in.) |
| E | 35.0 mm (1.37 in.) |
| F | 365.0 mm (1.20 ft.) |
| G | 410.0 mm (1.35 ft.) |
![]() |
Install the rear door front window frame moulding.
| *1 | Double-sided Tape |
Using a heat light, heat the vehicle body and rear door front window frame moulding.
Remove the release paper from the face of the rear door front window frame moulding.
Install the rear door front window frame moulding with the clip.
| 7. INSTALL REAR DOOR BELT MOULDING ASSEMBLY |
![]() |
Engage the 7 claws to install the rear door belt moulding assembly.
| 8. CONNECT REAR DOOR WEATHERSTRIP |
![]() |
Engage the clip and connect the rear door weatherstrip.
| 9. INSTALL REAR DOOR GLASS SUB-ASSEMBLY |
Connect the cable to the negative (-) battery terminal and the rear power window regulator motor connector.
Connect the power window regulator switch assembly and move the rear door glass sub-assembly so that the door glass bolts can be seen.
Disconnect the power window regulator switch assembly and rear power window regulator motor connector.
Disconnect the cable from the negative (-) battery terminal.
![]() |
Insert the rear door glass sub-assembly into the rear door panel along the rear door glass run as shown in the illustration.
Install the rear door glass sub-assembly with the 2 bolts.
Connect the cable to the negative (-) battery terminal.
| 10. INSTALL REAR DOOR REAR GUIDE SEAL |
Install the temporary screw to the rear door rear guide seal.
![]() |
Temporarily install the rear door rear guide seal.
| *1 | Temporary Screw |
Install the 2 screws.
Tighten the temporary screw to install the rear door rear guide seal.
| 11. INSTALL REAR DOOR WINDOW GUIDE SUB-ASSEMBLY |
![]() |
Install the screw.
Install the rear door window guide sub-assembly with the bolt.
| 12. INSTALL REAR DOOR GLASS RUN |
![]() |
Install the rear door glass run.
| 13. INSTALL REAR DOOR SERVICE HOLE COVER |
Apply butyl tape to the rear door panel.
![]() |
Pass the rear door lock remote control cable, rear door inside locking cable and each connector through a new rear door service hole cover.
Attach the rear door service hole cover according to the reference points on the rear door panel.
| *1 | Reference Point |
Connect the 2 connectors.
Engage the clamp.
| 14. INSTALL REAR DOOR TRIM BRACKET |
![]() |
Install the rear door trim bracket with the 2 screws.
| 15. INSTALL REAR DOOR FRAME GARNISH |
![]() |
Engage the clip to install a new rear door frame garnish.
| 16. INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY |
![]() |
Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly to the rear door inside handle.
![]() |
Engage the 2 claws and install the rear door inside handle sub-assembly to the rear door trim board sub-assembly.
| 17. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY |
for 8 Speakers:
Connect the connector.
![]() |
Engage the 8 clips and install the rear door trim board sub-assembly.
Install the 2 screws.
Remove the protective tape.
| 18. INSTALL REAR DOOR ARMREST COVER |
![]() |
Install the rear door armrest cover.
| 19. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL |
Connect the connector.
![]() |
Engage the 7 claws and 2 guides, and install the rear power window regulator switch assembly with rear door armrest base panel.
| 20. INSTALL DOOR ASSIST GRIP COVER |
![]() |
Engage the 6 claws, 2 clips and 3 guides, and install the assist grip cover.
| 21. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG |
![]() |
Engage the 3 claws and install the rear door inside handle bezel plug.
| 22. INSTALL REAR NO. 3 FLOOR BOARD |
![]() |
Engage the 2 guides to install the rear No. 3 floor board.
| 23. INSTALL REAR DECK FLOOR BOX |
Install the rear deck floor box.
| 24. INSTALL REAR NO. 2 FLOOR BOARD (for Separate Type) |
![]() |
Engage the 3 guides <A>.
Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.
| 25. INITIALIZE POWER WINDOW CONTROL SYSTEM |