Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › BLACK OUT TAPE (for Rear Door)

BLACK OUT TAPE (for Rear Door) > REMOVAL

for Preparation Click here



1. REMOVE REAR NO. 2 FLOOR BOARD (for Separate Type)


    B227787E01
  1. Disengage the 2 guides <A> as shown in the illustration.

  1. Disengage the 3 guides <B> and remove the rear No. 2 floor board.



2. REMOVE REAR DECK FLOOR BOX
  1. Remove the rear deck floor box.



3. REMOVE REAR NO. 3 FLOOR BOARD


    B227791
  1. Disengage the 2 guides and remove the rear No. 3 floor board.



4. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG


    B228784
  1. Using a moulding remover, disengage the 3 claws and remove the rear door inside handle bezel plug.



5. REMOVE DOOR ASSIST GRIP COVER


    B228789
  1. Using a moulding remover, disengage the 6 claws, 2 clips and 3 guides, and remove the door assist grip cover.



6. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    B228793
  1. Disengage the 7 claws and 2 guides.

  1. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.



7. REMOVE REAR DOOR ARMREST COVER


    B228795
  1. Remove the rear door armrest cover.



8. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    B228797E01
  1. Put protective tape around the rear door panel.
    Text in Illustration 
    *1
    Protective Tape



    B228799
  1. Remove the 2 screws.

  1. Using a clip remover, disengage the 8 clips.

  1. Pull out the rear door trim board sub-assembly in the direction indicated by the arrow in the illustration.

  1. Raise the rear door trim board sub-assembly and remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.



    B228803
  1. Disengage the 2 claws and disconnect the rear door inside handle sub-assembly.

  1. for 8 Speakers:

    1. Disconnect the connector.



9. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


    B228805
  1. Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly, and remove the rear door inside handle sub-assembly.



10. REMOVE REAR DOOR FRAME GARNISH


    B228813
  1. Disengage the clip and remove the rear door frame garnish.

    HINT:
    This garnish needs to be replaced with a new one because the clip will break when removing the rear door frame garnish.



11. REMOVE REAR DOOR TRIM BRACKET


    B228818
  1. Remove the 2 screws and rear door trim bracket.



12. REMOVE REAR DOOR SERVICE HOLE COVER


    B228820
  1. Disconnect the 2 connectors.

  1. Disengage the clamp and remove the rear door service hole cover.

    HINT:
    Remove any remaining butyl tape from the door.



13. REMOVE REAR DOOR GLASS RUN


    B228828
  1. Remove the rear door glass run.



14. REMOVE REAR DOOR WINDOW GUIDE SUB-ASSEMBLY


    B228830
  1. Remove the screw.

  1. Remove the bolt and rear door window guide sub-assembly.



15. REMOVE REAR DOOR REAR GUIDE SEAL


    B228832E01
  1. Loosen the temporary screw.
    Text in Illustration 
    *1
    Temporary Screw

  1. Remove the 2 screws and rear door rear guide seal.

  1. Remove the temporary screw from the rear door window division bar sub-assembly.



16. REMOVE REAR DOOR GLASS SUB-ASSEMBLY
  1. Connect the rear power window regulator motor connector.

  1. Connect the power window regulator switch assembly and move the rear door glass sub-assembly so that the door glass bolts can be seen.

  1. Disconnect the power window regulator switch assembly and rear power window regulator motor connector.

  1. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



    B228834
  1. Remove the 2 bolts and rear door glass sub-assembly as shown in the illustration.

    NOTICE:
    1. After the bolts are removed, do not allow the door glass to fall.
    2. Do not damage the door glass.



17. REMOVE REAR DOOR BELT MOULDING ASSEMBLY


    B229333E01
  1. Put protective tape around the rear door belt moulding assembly.
    Text in Illustration 
    *1
    Protective Tape



    B229334
  1. Using a screwdriver, disengage the 7 claws and remove the rear door belt moulding assembly.



18. REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING

HINT:
When removing the rear door front window frame moulding, heat the vehicle body and rear door front window frame moulding using a heat light.

Heating Temperature 
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
Moulding
20 to 30°C (68 to 86°F)

NOTICE:
Do not heat the vehicle body or rear door front window frame moulding moulding excessively.

  1. Using a heat light, heat the rear door front window frame moulding.



    B229342E01
  1. Using a moulding remover, remove the clip and rear door front window frame moulding.
    Text in Illustration 
    *1
    Double-sided Tape



19. DISCONNECT REAR DOOR WEATHERSTRIP


    B229398
  1. Using a clip remover, disengage the clip and remove the upper part of the rear door weatherstrip to the extent that allows removal of the rear door strip and black out tape.



20. REMOVE NO. 2 BLACK OUT TAPE
  1. Using a heat light, heat the No. 2 black out tape and vehicle body.
    Heating Temperature 
    Item
    Temperature
    Vehicle Body
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.



    B229399
  1. Pull back on one of the ends of the No. 2 black out tape to remove it.

    HINT:
    When pulling on the tape, pull it parallel to the body.



21. REMOVE REAR DOOR OUTSIDE STRIPE
  1. Using a heat light, heat the rear door outside stripe and vehicle body.
    Heating Temperature 
    Item
    Temperature
    Vehicle Body
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.



    B229402
  1. Pull back on one of the ends of the rear door outside stripe to remove it.

    HINT:
    When pulling on the stripe, pull it parallel to the body.



22. REMOVE REAR DOOR UPPER OUTSIDE STRIPE
  1. Using a heat light, heat the rear door upper outside stripe and vehicle body.
    Heating Temperature 
    Item
    Temperature
    Vehicle Body
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.



    B229406
  1. Pull back on one of the ends of the rear door upper outside stripe to remove it.

    HINT:
    When pulling on the stripe, pull it parallel to the body.



23. REMOVE REAR DOOR LOWER OUTSIDE STRIPE
  1. Using a heat light, heat the rear door lower outside stripe and vehicle body.
    Heating Temperature 
    Item
    Temperature
    Vehicle Body
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.



    B229404
  1. Pull back on one of the ends of the rear door lower outside stripe to remove it.

    HINT:
    When pulling on the stripe, pull it parallel to the body.