Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

HYBRID CONTROL SYSTEM > Pattern Select Switch Eco Mode Circuit

for Preparation Click here


DESCRIPTION

When selecting ECO mode, the switch operation signal is sent to the air conditioning amplifier assembly. Following this, ECO mode control is activated for the heater and air conditioning system.

WIRING DIAGRAM


C190514E15


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM (CAN BUS CHECK)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: System Select / CAN Bus Check.

    Result:
    Result
    Proceed to
    All of the ECUs and sensors that are currently connected to the CAN communication system are displayed.
    A
    None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed.
    B

  1. Turn the power switch off.



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2.CHECK DTC OUTPUT (HEALTH CHECK)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: System Select / Health Check.

  1. Check DTCs.
    Result 
    Result
    Proceed to
    No DTCs are output.
    A
    DTCs are output.
    B

  1. Turn the power switch off.



B
GO TO DTC CHART
A


3.PERFORM ACTIVE TEST USING TECHSTREAM (COMBINATION METER)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Body Electrical / Combination Meter / Active Test / Indicat. ECO Mode.

  1. Perform the "Indicat. ECO Mode" Active Test.

    OK 
    Tester Display
    Description
    Inspection Condition
    Specified Condition
    Indicat. ECO Mode
    ECO mode indicator light
    ECO mode
    Comes on

    Result:
    Result
    Proceed to
    The ECO mode indicator light comes on
    A
    The ECO mode indicator light does not come on
    B



B
CHECK METER / GAUGE SYSTEM (Click here)
A


4.READ VALUE USING TECHSTREAM (ECO SWITCH)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Body Electrical / Air Conditioning / Data List / ECO Switch.

  1. Read the value displayed on the Techstream.

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ECO Switch
    ECO MODE switch condition/
    ON or OFF
    ECO MODE switch ON:
    ON
    ECO MODE switch OFF:
    OFF
    -

    Result:
    Result
    Proceed to
    The Techstream display changes according to the ECO MODE switch operation.
    A
    The Techstream display does not changes according to the ECO MODE switch operation.
    B



B
Go to step 5
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

5.INSPECT INTEGRATION CONTROL AND PANEL SUB-ASSEMBLY (ECO MODE SWITCH)
  1. Remove the integration control and panel sub-assembly (ECO MODE switch).



    C210637E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L78-2 (ECU) - L78-5 (E)
    ECO MODE Switch ON
    Below 1 Ω
    L78-2 (ECU) - L78-5 (E)
    ECO MODE Switch OFF
    10 kΩ or higher

Text in Illustration 
*1
Component without harness connected
(Integration Control and Panel Sub-assembly (ECO MODE Switch))
  1. Install the integration control and panel sub-assembly.



NG
REPLACE INTEGRATION CONTROL AND PANEL SUB-ASSEMBLY (ECO MODE SWITCH) (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (ECO MODE SWITCH - BODY GROUND)
  1. Disconnect connector L78 from the integration control and panel sub-assembly (ECO MODE switch).



    C210638E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L78-5 (E) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*1
Front view of wire harness connector
(to Integration Control and Panel Sub-assembly (ECO MODE Switch))
  1. Connect the integration control and panel sub-assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (ECO MODE SWITCH - AIR CONDITIONING AMPLIFIER ASSEMBLY)
  1. Disconnect connector L78 from the integration control and panel sub-assembly (ECO MODE switch).

  1. Disconnect connector L17 from the air conditioning amplifier assembly.



    C210640E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L78-2 (ECU) - L17-15 (ECOS)
    Always
    Below 1 Ω
    L78-2 (ECU) or L17-15 (ECOS) - Body ground
    Always
    10 kΩ or higher

Text in Illustration 
*1
Front view of wire harness connector
(to Integration Control and Panel Sub-assembly (ECO MODE Switch))
*2
Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)
  1. Connect the air conditioning amplifier assembly connector.

  1. Connect the integration control and panel sub-assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)