Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › SFI SYSTEM

DTC    P0403    Exhaust Gas Recirculation Control Circuit

for Preparation Click here


DESCRIPTION

Refer to DTC P0401 .

DTC No.
DTC Detection Condition
Trouble Area
P0403
Open or short in EGR valve assembly circuit
(1 trip detection logic)
  1. Open or short in EGR valve assembly circuit
  2. EGR valve assembly
  3. ECM

MONITOR DESCRIPTION

This DTC is designed to detect an open or short in the EGR valve assembly circuit.
Example:
  1. If the EGR1, EGR2, EGR3 or EGR4 terminal output voltage is excessively low, but the step motor is still operating, the ECM determines that there is a short in the EGR valve assembly circuit , and stores the DTC.
  2. If the EGR1, EGR2, EGR3 or EGR4 terminal output voltage is excessively low, and the step motor is not operating, the ECM determines that there is an open in the EGR valve assembly circuit, and stores the DTC.

MONITOR STRATEGY


Related DTCs
P0403: EGR valve circuit range check
Required Sensors/Components (Main)
EGR valve assembly
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
-
MIL Operation
Immediately
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs are not present
None
All of the following conditions are met
-
Engine
Running
Auxiliary battery voltage
10.5 V or more
Time after power switch off to on (IG)
More than 0.5 seconds

TYPICAL MALFUNCTION THRESHOLDS


One of the following conditions is met
Conditions A, B, C or D
A. All of the following conditions are met
Conditions 1 and 2
1. EGR1 output terminal voltage
Low voltage
2. Either of the following conditions is met
Condition (a) or (b)
(a) Step motor
Driving
(b) EGR1
Not operating
B. All of the following conditions are met
Conditions 1 and 2
1. EGR2 output terminal voltage
Low voltage
2. Either of the following conditions is met
Condition (a) or (b)
(a) Step motor
Driving
(b) EGR2
Not operating
C. All of the following conditions are met
Conditions 1 and 2
1. EGR3 output terminal voltage
Low voltage
2. Either of the following conditions is met
Condition (a) or (b)
(a) Step motor
Driving
(b) EGR3
Not operating
D. All of the following conditions are met
Conditions 1 and 2
1. EGR4 output terminal voltage
Low voltage
2. Either of the following conditions is met
Condition (a) or (b)
(a) Step motor
Driving
(b) EGR4
Not operating

CONFIRMATION DRIVING PATTERN


A215251E08

  1. Connect the Techstream to the DLC3.
  2. Turn the power switch on (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the power switch off and wait for at least 30 seconds.
  5. Turn the power switch on (IG) and turn the Techstream on [A].
  6. Put the engine in inspection mode (maintenance mode) (Click here).
  7. Start the engine and warm it up [B].
  8. Drive the vehicle at 20 km/h (12 mph) or more for 10 minutes [C].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].
  10. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P0403.
  13. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system has a normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  14. If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A220107E04


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or more.

    HINT:
    The A/C switch and all accessory switches should be off.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Throttle Idle Position and MAP.

  1. Check that the Throttle Idle Position in ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.

    HINT:
    1. Do not leave the EGR valve open for 10 seconds or more during the Active Test.
    2. Be sure to return the EGR valve to step 0 when the Active Test is completed.
    3. Do not open the EGR valve 30 steps or more during the Active Test.

    OK:
    MAP and idling condition change in response to EGR step position when Throttle Idle Position is ON in Data List.


    Standard:

    -
    EGR Step Position (Active Test)
    0 Steps
    0 to 30 Steps
    Idling condition
    (Throttle Idle Position: ON)
    Steady idling
    Idling changes from steady to rough idling or engine stalls
    MAP
    (Data List)
    MAP value is 20 to 40 kPa (150 to 300 mmHg)
    (EGR valve is fully closed)
    MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed

    HINT:
    During Active Test, if the idling condition does not change in response to EGR step position, then there is probably a malfunction in the EGR valve.


    Result:

    Result
    Proceed to
    Within standard range
    A
    Outside of standard range
    B



B
Go to step 2
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.INSPECT EGR VALVE ASSEMBLY
  1. Inspect the EGR valve assembly (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the EGR valve assembly (Click here).



NG
REPLACE EGR VALVE ASSEMBLY (Click here)
OK


3.INSPECT EGR VALVE ASSEMBLY (+B1 OR +B2 VOLTAGE)
A209148E12
  1. Disconnect the EGR valve assembly connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
D10-2 (+B1) - Body ground
Power switch on (IG)
11 to 14 V
D10-5 (+B2) - Body ground
Power switch on (IG)
11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to EGR Valve Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (EGR VALVE ASSEMBLY - EFI MAIN RELAY)
OK


4.CHECK HARNESS AND CONNECTOR (ECM - EGR VALVE ASSEMBLY)
  1. Disconnect the EGR valve assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.


Standard Resistance (Check for Open):

Tester Connection
Condition
Specified Condition
D28-45 (EGR1) - D10-4 (EGR1)
Always
Below 1 Ω
D28-44 (EGR2) - D10-3 (EGR2)
Always
Below 1 Ω
D28-43 (EGR3) - D10-6 (EGR3)
Always
Below 1 Ω
D28-42 (EGR4) - D10-1 (EGR4)
Always
Below 1 Ω


Standard Resistance (Check for Short):

Tester Connection
Condition
Specified Condition
D28-45 (EGR1) or D10-4 (EGR1) - Body ground
Always
10 kΩ or higher
D28-44 (EGR2) or D10-3 (EGR2) - Body ground
Always
10 kΩ or higher
D28-43 (EGR3) or D10-6 (EGR3) - Body ground
Always
10 kΩ or higher
D28-42 (EGR4) or D10-1 (EGR4) - Body ground
Always
10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)