Home › Audio / Visual / Telematics › CELLULAR COMMUNICATION › TELEPHONE AND GPS ANTENNA CORDS

TELEPHONE AND GPS ANTENNA CORDS > INSTALLATION

for Preparation Click here



1. INSTALL TELEPHONE AND GPS ANTENNA CORD SUB-ASSEMBLY

HINT:
Double-sided tape and tape are not available as supply parts. If the tape still has enough adhesion to secure the roof headlining and antenna cord, reuse it. If the roof headlining has been replaced with a new one, or if the tape and/or the double-sided tape is no longer sticky, apply new tape following the procedure below.

If the double-sided tape cannot be reused:


  1. Peel off the release paper from one side of new double-sided tape and apply the new double-sided tape to the position indicated in the illustration. Be careful not to touch the adhesive surface.


    E200214E01

    Area
    Dimension
    X
    1.0 mm (0.0394 in.)
    Y
    10.0 mm (0.394 in.)

    NOTICE:
    Be sure to apply the double-sided tape carefully so that the tape will not be misaligned or come off.



    E200215E01

    Area
    Dimension
    X
    1.0 mm (0.0394 in.)
    Y
    10.0 mm (0.394 in.)

    NOTICE:
    Be sure to apply the double-sided tape carefully so that the tape will not be misaligned or come off.

  1. Peel off the release paper from the double-sided tape. Be careful not to touch the adhesive surface.



  1. Align the vehicle front side marking (pink) on the telephone and GPS antenna cord sub-assembly with the vehicle front side tab on the roof headlining, and wrap the tape over the antenna cord to install it. (1)


    E200204E01

    HINT:
    If the tape cannot be reused, packing tape can be used as a substitute.

  1. Temporarily install the front side of the telephone and GPS antenna cord sub-assembly (2) with the adhesive tape.

  1. Temporarily install the front side of the telephone and GPS antenna cord sub-assembly (3) with the adhesive tape.

  1. Temporarily install the telephone and GPS antenna cord sub-assembly by placing it on the double-sided tape from the front of the vehicle to the point just before the extra cord storage area.

  1. Align the vehicle rear marking (pink) on the telephone and GPS antenna cord sub-assembly with the tape attachment location (scribe line) of the roof headlining, and wrap the tape over the antenna cord to install it. (4)

    HINT:
    If the tape cannot be reused, packing tape can be used as a substitute.

  1. Temporarily install the rear side of the telephone and GPS antenna cord sub-assembly (5) with the adhesive tape.

  1. Temporarily install the telephone and GPS antenna cord sub-assembly by placing it on the double-sided tape from the rear of the vehicle to the point just before the extra cord storage area.



    E191252E01
  1. Using double-sided tape, place any excess telephone and GPS antenna cord sub-assembly in the extra cord storage area to finish installing the antenna cord.

    HINT:
    Attach 3 pieces of double-sided tape to the extra cord storage area as shown in the illustration.



2. INSTALL NO. 3 ROOF SILENCER PAD (w/o Sliding Roof)


  1. Align the markings on the roof headlining assembly with the No. 3 roof silencer pad and install the set plate using hot-melt glue as shown in the illustration.


    B311296E01


    Text in Illustration 
    *1
    Roof Silencer Pad Marking
    *2
    Hot-melt Glue Marking



3. INSTALL NO. 2 ROOF SILENCER PAD (w/o Sliding Roof)


  1. Align the markings on the roof headlining assembly with the No. 2 roof silencer pad and install the set plate using hot-melt glue as shown in the illustration.


    B311297E01


    Text in Illustration 
    *1
    Roof Silencer Pad Marking
    *2
    Hot-melt Glue Marking



4. INSTALL ROOF HEADLINING ASSEMBLY

HINT:
Refer to the procedure from Install Roof Headlining Assembly (Click here).