Home › Audio / Visual / Telematics › CELLULAR COMMUNICATION › SAFETY CONNECT SYSTEM

DTC    B1571    Manual (SOS) Switch Green Indicator Malfunction

for Preparation Click here


DESCRIPTION

This DTC is set when the DCM (Telematics Transceiver) detects an open or short in the manual (SOS) switch green indicator circuit of the manual (SOS) switch. The manual (SOS) switch green indicator illuminates after the power switch is turned on (IG).
If the Safety Connect system is not active, the manual (SOS) switch green indicator will turn off.
If the Safety Connect system is active, the manual (SOS) switch green indicator will blink while communicating with call center.

DTC No.
DTC Detection Condition
Trouble Area
B1571
Current for manual (SOS) switch green indicator reaches malfunction criteria for 10 seconds when power switch is on (IG).
  1. Map light assembly
  2. Wire harness or connector
  3. DCM (Telematics Transceiver)

WIRING DIAGRAM


w/o Sliding Roof

B235169E17


w/ Sliding Roof

B235169E18


INSPECTION PROCEDURE

1.CHECK DTC
  1. Turn the power switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG) and wait for 10 seconds.

  1. Turn the Techstream on.

  1. Perform "HEALTH CHECK" and check for current DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1570 and B1571 are output
    A
    DTC B1571 is output
    (DTC B1570 is not output)
    B



B
Go to step 6
A


2.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - BODY GROUND)
  1. Remove the map light assembly but do not disconnect the connectors (Click here).



    B234642E01
  1. w/o Sliding Roof:

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      U3-1 (GND1) - Body ground
      Always
      Below 1 Ω

      Text in Illustration 
      *1
      Component with harness connected
      (Map Light Assembly)



    B234643E01
  1. w/ Sliding Roof:

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      U13-9 (GND1) - Body ground
      Always
      Below 1 Ω

      Text in Illustration 
      *1
      Component with harness connected
      (Map Light Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT MAP LIGHT ASSEMBLY (GREEN INDICATOR)
  1. Disconnect the U3*1 or U13*2 map light assembly connector.

    1. *1: w/o Sliding Roof
    2. *2: w/ Sliding Roof

  1. Connect 2 dry-cell batteries (1.5 V each) in series.



    B234642E03
  1. w/o Sliding Roof:

    1. Connect the positive (+) lead to terminal U3-13 (IND2) and the negative (-) lead to terminal U3-1 (GND1) of the map light assembly connectors.

    2. Check if the illumination for the manual (SOS) switch red indicator comes on.

      OK:
      Red indicator comes on.

      Text in Illustration 
      *1
      Component without harness connected
      (Map Light Assembly)



    B234643E03
  1. w/ Sliding Roof:

    1. Connect the positive (+) lead to terminal U13-17 (IND2) and the negative (-) lead to terminal U13-9 (GND1) of the map light assembly connectors.

    2. Check if the illumination for the manual (SOS) switch red indicator comes on.

      OK:
      Red indicator comes on.

      Text in Illustration 
      *1
      Component without harness connected
      (Map Light Assembly)



NG
REPLACE MAP LIGHT ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) - MAP LIGHT ASSEMBLY)
  1. Disconnect the L144 DCM (Telematics Transceiver) connector.



    B234644E14
  1. w/o Sliding Roof:

    1. Measure the resistance according to the value(s) in the table below .

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      L144-12 (IND2) - U3-13 (IND2)
      Always
      Below 1 Ω

      Text in Illustration 
      *1
      Front view of wire harness connector
      (to DCM (Telematics Transceiver))
      *2
      Front view of wire harness connector
      (to Map Light Assembly)



    B234645E08
  1. w/ Sliding Roof:

    1. Measure the resistance according to the value(s) in the table below .

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      L144-12 (IND2) - U13-17 (IND2)
      Always
      Below 1 Ω

      Text in Illustration 
      *1
      Front view of wire harness connector
      (to DCM (Telematics Transceiver))
      *2
      Front view of wire harness connector
      (to Map Light Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.REPLACE DCM (TELEMATICS TRANSCEIVER)
  1. Replace DCM (Telematics Transceiver) (Click here).

    NOTICE:
    1. The power switch must be off.
    2. Do not swap the DCM (Telematics Transceiver) with one from another vehicle.


NEXT

PERFORM DCM ACTIVATION (Click here)  

6.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH GREEN INDICATOR CONDITION)
  1. Confirm the green indicator status after the power switch on (IG) (Click here).

    Result:
    Result
    Proceed to
    Green indicator remains off.
    A
    Green indicator remains on.
    B



B
Go to step 10
A


7.INSPECT MAP LIGHT ASSEMBLY (GREEN INDICATOR INPUT VOLTAGE)
  1. Remove the map light assembly but do not disconnect the connectors (Click here).



    B129570E06
  1. w/o Sliding Roof:

    1. Connect the positive lead of a voltmeter to terminal U3-13 (IND2), and the negative lead to terminal U3-1 (GND1).

    2. Measure the voltage.

      Standard:
      1.0 to 8.5 V for 2 seconds after the power switch is on (IG).
      0 V when the power switch is off.

      Text in Illustration 
      *1
      Component with harness connected
      (Map Light Assembly)



    E190229E03
  1. w/ Sliding Roof:

    1. Connect the positive lead of a voltmeter to terminal U13-17 (IND2), and the negative lead to terminal U13-9 (GND1).

    2. Measure the voltage.

      Standard:
      1.0 to 8.5 V for 2 seconds after the power switch is on (IG).
      0 V when the power switch is off.

      Text in Illustration 
      *1
      Component with harness connected
      (Map Light Assembly)



NG
Go to step 8
OK

REPLACE MAP LIGHT ASSEMBLY (Click here)  

8.INSPECT DCM (TELEMATICS TRANSCEIVER) (GREEN INDICATOR OUTPUT VOLTAGE)


    B235166E80
  1. Remove the DCM (Telematics Transceiver) but do not disconnect the connectors (Click here).

  1. Connect the positive lead of a voltmeter to terminal L144-12 (IND2), and the negative lead to body ground.

  1. Measure the voltage.

    Standard:
    1.0 to 8.5 V for 2 seconds after the power switch is on (IG) and red indicator has turned off.
    0 V when the power switch is off.

    Text in Illustration 
    *1
    Component with harness connected
    (DCM (Telematics Transceiver))



NG
Go to step 9
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR 

9.CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) - BODY GROUND)


    B235166E80
  1. Remove the DCM (Telematics Transceiver) but do not disconnect the connectors (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L144-12 (IND2) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Component with harness connected
    (DCM (Telematics Transceiver))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.REPLACE DCM (TELEMATICS TRANSCEIVER)
  1. Replace the DCM (Telematics Transceiver) (Click here).

    NOTICE:
    1. The power switch must be off.
    2. Do not swap the DCM (Telematics Transceiver) with one from another vehicle.


NEXT

PERFORM DCM ACTIVATION (Click here)