Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER PUMP

BRAKE BOOSTER PUMP > INSTALLATION

for Preparation Click here



1. INSTALL BRAKE BOOSTER PUMP ASSEMBLY


    C208396E01
  1. Install the brake booster pump assembly, brake booster pump bushings and brake actuator case collars to the brake actuator bracket assembly with the 2 nuts.
    Text in Illustration 
    *1
    Nut
    *2
    Brake Actuator Case Collar
    *3
    Brake Booster Pump Bushing
    *4
    Brake Actuator Bracket Assembly
    *5
    Brake Booster Pump Assembly
    *6
    Cushion

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    NOTICE:
    1. Do not drop the brake booster pump assembly when carrying it.
    2. Do not carry the brake booster pump assembly by the connector.
    3. Confirm that the 2 cushions are on the brake actuator bracket, bushings and collars on the brake booster pump assembly when assembling the brake booster pump assembly.
    4. Do not remove the hole plug before installing a new brake booster pump assembly because the brake booster pump assembly is filled with brake fluid.



2. INSTALL BRAKE BOOSTER PUMP ASSEMBLY WITH BRACKET


    C210144E01
  1. Using SST, install the brake booster pump assembly with bracket with the 3 nuts.

    SST
    09961-00950  

    Torque:
    without SST:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }
    with SST:
    12 N*m{ 121 kgf*cm , 9 ft.*lbf }

    NOTICE:
    1. Use a torque wrench with a fulcrum length of 250 mm (9.84 in.).
    2. Tighten the 3 nuts in the order shown in the illustration.
    3. Do not damage the fuel line, the brake lines and wire harness.
    4. Use the formula to calculate special torque values for situations where the SST is combined with a torque wrench (Click here).



    C212065E01
  1. Install the wire harness clamp, 2 fuel lines and front No. 4 brake tube to the brake booster pump assembly.

    NOTICE:
    Do not damage the fuel line, the brake lines and wire harness.

    Text in Illustration 
    *1
    Wire Harness Clamp
    *2
    Fuel Line
    *3
    Front No. 4 Brake Tube



  1. Connect the front No. 1 brake tube.



      C208389E01
    1. Install the No. 2 brake tube clamp to the brake booster pump assembly with the bolt.

      Torque:
      7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

      Text in Illustration 
      *1
      Brake Actuator Hose
      *2
      No. 2 Brake Tube Clamp
      *3
      No. 1 Brake Tube Clamp
      *4
      Front No. 1 Brake Tube

    2. Install the front No. 1 brake tube to the brake booster pump assembly.

      Torque:
      15 N*m{ 155 kgf*cm , 11 ft.*lbf }

      NOTICE:
      1. This torque value is effective when the union nut wrench is parallel to the torque wrench.
      2. Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench (Click here).

    3. Install the No. 1 brake tube clamp to the brake booster pump assembly with the bolt.

      Torque:
      7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Install the brake actuator hose and clip.



    C208392
  1. Install the wire harness clamp.

  1. Connect the 2 connectors.



3. INSTALL NO. 5 BRAKE ACTUATOR BRACKET


    C208393E01
  1. Install the No. 5 brake actuator bracket with the 2 nuts.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    Tighten the 2 nuts in the order shown in the illustration.

  1. Install the wire harness clamp.



4. INSTALL FRONT CROSS MEMBER SUB-ASSEMBLY

HINT:
Refer to the procedure from Install Front Cross Member Sub-assembly (Click here).



5. INSTALL BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

HINT:
Refer to the procedure from Install Brake Booster with Master Cylinder Assembly (Click here).



6. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
  1. Adjust front wheel alignment (Click here).