Home › Audio / Visual / Telematics › CELLULAR COMMUNICATION › SAFETY CONNECT SYSTEM

DTC    B15C4    Airbag Signal Malfunction/Not Input

for Preparation Click here


DESCRIPTION

If the DCM (Telematics Transceiver) detects an error in communication between the DCM (Telematics Transceiver) and the center airbag sensor assembly as a result of the DCM (Telematics Transceiver) self check, this DTC will be set.

DTC No.
DTC Detection Condition
Trouble Area
B15C4
DCM (Telematics Transceiver) detects an error in signals from center airbag sensor assembly when power switch is on (IG).
  1. Airbag system
  2. Wire harness or connector
  3. Center airbag sensor assembly
  4. DCM (Telematics Transceiver)

WIRING DIAGRAM


E196665E30


INSPECTION PROCEDURE

1.CHECK DTC (AIRBAG SYSTEM)
  1. Turn the power switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG) and wait for 10 seconds.

  1. Turn the Techstream on.

  1. Check the DTC of "AIRBAG SYSTEM" (Click here).

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
GO TO AIRBAG SYSTEM (Click here)
A


2.INSPECT DCM (TELEMATICS TRANSCEIVER) (GSW SIGNAL)


    B240640E17
  1. Remove the DCM (Telematics Transceiver) but do not disconnect the connectors (Click here).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L144-24 (GSW) - Body ground
    Power switch on (IG)
    6.5 to 8.5 V

    Text in Illustration 
    *1
    Component with harness connected
    (DCM (Telematics Transceiver))

    Result:
    Result
    Proceed to
    8.5 V or higher
    A
    Below 6.5 V
    B
    6.5 to 8.5 V
    C

    Reference Waveform 
    Item
    Condition
    Tester connection
    L144-24 (GSW) - Body ground
    Tool setting
    5.0 V/DIV., 20 ms/DIV.
    Vehicle condition
    Power switch on (IG)



B
Go to step 4

C
Go to step 5
A


3.CHECK HARNESS AND CONNECTOR (FOR OPEN CIRCUIT)


    B242282E04
  1. Remove the center airbag sensor assembly but do not disconnect the connectors (Click here)

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L16-24 (GSW3) - Body ground
    Power switch on (IG)
    8.5 V or higher

    Text in Illustration 
    *1
    Component with harness connected
    (Center Airbag Sensor Assembly)
    Reference Waveform 
    Item
    Condition
    Tester connection
    L16-24 (GSW3) - Body ground
    Tool setting
    5.0 V/DIV., 20 ms/DIV.
    Vehicle condition
    Power switch on (IG)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)  

4.CHECK HARNESS AND CONNECTOR (FOR SHORT CIRCUIT)


    E192516E53
  1. Disconnect the L144 DCM (Telematics Transceiver) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L144-24 (GSW) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connected
    (DCM (Telematics Transceiver))



NG
Go to step 6
OK


5.REPLACE DCM (TELEMATICS TRANSCEIVER)
  1. Replace the DCM (Telematics Transceiver) (Click here).

    NOTICE:
    1. The power switch must be off.
    2. Do not swap the DCM (Telematics Transceiver) with one from another vehicle.


NEXT

PERFORM DCM ACTIVATION (Click here)  

6.CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) - CENTER AIRBAG SENSOR ASSEMBLY)


    E196667E26
  1. Disconnect the L144 DCM (Telematics Transceiver) connector.

  1. Disconnect the L16 center airbag sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L144-24 (GSW) - L16-24 (GSW3)
    Always
    Below 1 Ω
    L144-24 (GSW) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to DCM (Telematics Transceiver))
    *2
    Front view of wire harness connector
    (to Center Airbag Sensor Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)